Monday, November 17, 2014
How to Install a Driving Light on a Harley Davidson Softail
Harley-Davidson driving lights mount on the front forks of Softails. The driving lights may add slightly to your view of the road at night. They add significantly to the recognition by oncoming drivers that you are there. The pattern formed by a headlight and two driving lights is conspicuous, and driving lightbulbs are often yellow, so even drunks are inclined to slow down when they see you coming. The popular Heritage Softail Classic, styled to look like a mid-60s hog, comes equipped with three lights as standard equipment. If that is the effect you are trying to achieve, numerous aftermarket vendors, including Harley and Kuryakyn, sell driving light kits. These instructions are specific to recent, fuel-injected Softails.
Instructions
Remove Fuel Tank
- 1
Remove the electrical caddy cover by pulling on it with both hands. Pry the fuel pump fuse out of the electrical caddy with a small, flathead screwdriver.
2Start the engine in neutral and run the engine until it dies. Run the starter for four more seconds.
3Disconnect the fuel supply line by pulling up on the chrome sleeve of the fuel tank quick-connect fitting and pulling down on the fuel supply line.
4Unscrew the bolt that secures the seat tab to the rear fender. Recent Softails use a Phillips screw, which must be removed with a screwdriver. Older Softails use an Allen bolt, which comes off with an Allen wrench.
5Remove the seat to access the battery compartment. Disconnect the negative battery wire from the negative terminal with an open-end wrench.
6Remove the instrument panel by loosening and removing the acorn nut on the panel with an Allen wrench and pulling up. Unplug the fuel pump module connector under the instrument panel.
7Push a 5/16-inch-diameter bolt in one end of a foot long piece of 5/16-inch rubber hose. Tighten a hose clamp around the hose and the bolt with a flathead screwdriver.
8Cut the hose clamp from one end of the crossover hose with side blade pliers. Very quickly replace the crossover hose on the fuel tank fitting with the open end of the 1-foot hose while directing the flow of gasoline from the free end of the crossover hose into an adequately sized gas can.
9Clean up spilled gasoline with rags. Carry the rags outside if you are working in a garage.
10Disconnect the crossover hose and the continuous venting vent line. Remove the front tank mounting bolt, flat washers and acorn nut with an open-end wrench.
11Remove the rear mounting bolt, flat washers and nut with an open-end wrench. Disconnect the fuel gauge connector under the left side of the fuel tank with your hands.
12Lift the tank straight up to remove. Set the tank on a well-padded surface in a well-ventilated place.
Install Lights
- 13
Install the left-hand and right-hand side specific mounting clamps that came with the driving light kit on the right and left fork tubes using the four buttonhead screws that came with the driving light kit. Tighten the screws to between 70 and 80 inch-pounds of torque with an Allen socket and a torque wrench.
14Route each lamp wire through the hole in each mounting bracket and secure the lamp to each bracket using a clamp block, lock washer and retainer from the kit. Tighten the retainer to 18 foot-pounds of torque with an open-end socket and a torque wrench.
15Position the inner nesting rings from the kit on each lightbulb. Connect the black wires to the bulb spade terminals next to the bulbs indexing tabs. Install the gray wires on the remaining spade terminals.
16Attach the bulbs and the inner nesting rings to the outer trim rings with the Phillips screws included in the kit. Slide the conduit tubes from the kit over both lamp wires.
17Set the light kit wiring harness relay in the seat pan. Route the long leg of the harness along the frame spine under the seat.
18Plug the white wire connector into the "B+" connector on the lighting kit wiring harness. Loosen and remove the nut on the ground wire stud in the seat pan with a socket wrench and socket.
19Slip the black, ground wire ring over the ground wire stud. Replace the ground wire stud nut. Secure the driving light kit wire harness to the adjacent wiring harnesses with the cable straps included in the driving light kit.
20Route the driving light wiring harness past the steering head. Route the lamp switch leg of the harness along the left side of the handlebar to the clutch control.
21Unscrew the boot from the small lamp switch in the kit. Install the switch into the switch mounting bracket in the kit and replace the boot on the switch.
22Remove the lower screw and washer from the clutch control clamp with a Torx driver. Position the tab of the driving light switch bracket over the screw hole and replace the Torx screw and washer. Tighten the screw to 70 inch-pounds of torque with a Torx socket and torque wrench.
23Loosen the headlight trim ring clamp with a Phillips screwdriver. Remove the headlight trim ring.
24Pull the connector block from the headlight bulb prongs. Remove the rubber boot from the back of the headlight lens.
25Squeeze the wire retaining clip ends to unhook them from the notches in the headlight assembly. Pivot the wire retaining clip away from the headlight bulb and remove the bulb from the headlight assembly.
26Route the unconnected wire from the handlebar switch through the grommet into the headlight housing. Splice that wire to the yellow (low-beam) headlight wire using the electrical connector included in the driving light kit.
27Reinstall the headlight bulb.
28Slide the heat-shrink tubing included in the kit over the white wire in the driving light wiring harness. Strip the ends of both lamp wires with a wire stripper.
29Splice the white wire to the lamp wires with the three wire connector included in the kit with a wire crimping tool. Cover the splice with the heat shrink tubing and shrink the tubing with a heat gun.
30Clip the driving light wires to the lower fork steering bracket using the adhesive-backed clips from the kit.
31Reinstall the fuel tank. Reconnect the negative battery cable.
32Reinstall the fuel pump fuse. Replace the electrical caddy cover. Replace the seat.
Saturday, May 3, 2014
How to Change the Brake Light Bulb on a 2007 TrailBlazer
In 1983, Chevrolet introduced a mid-sized SUV to the market, known as the Blazer. The Blazer gave drivers the usefulness of an SUV, without the bulk of a full-sized SUV. In 2002, the Trailblazer replaced all four-door Blazers and finally, in 2006, the Trailblazer replaced the Blazer altogether. The 2007 Trailblazer came standard with a 4.2-liter, in-line six-cylinder engine that produced 291 horsepower and 277 foot-pounds of torque. The 2007 Trailblazers styling was similar to that of its Blazer predecessor, including the vertical taillight assemblies. Replacing the brake light bulbs in these vertical taillight assemblies is a relatively easy task.
Instructions
- 1
Open the rear hatch and remove the two screws on the inner part of the taillight assembly with a Phillips screwdriver.
2Pull the taillight assembly rearward to remove it from the Trailblazers body. Unplug the wiring harness from the rear of the taillight assembly, by pressing the locking button and pulling the harness away from the assembly.
3Turn the taillight assembly over and remove the three screws holding the socket plate -- the roughly 2-by-5-inch plastic plate on the rear of the taillight assembly. Pull the socket plate from the taillight assembly; notice the bulbs remain attached to the plate.
4Pull the burnt-out brake bulb from the socket plate with a slight wiggling motion. Grab a new 3157 brake light bulb with a clean, lint-free cloth and press it into the socket. Never touch the glass part of the bulb with your bare hands, as the oils from your hands can cause the bulb to burn out prematurely.
5Set the socket plate back on the rear of the taillight assembly and tighten the three screws with a Phillips screwdriver.
6Plug the wiring harness back into the socket plate and set the taillight assembly back on the rear of the Trailblazer. Tighten the two screws on the inner part of the taillight assembly with a Phillips screwdriver.
7Close the Trailblazers hatch.
Tuesday, March 18, 2014
How to Remove the Light Switch From the Panel in a 2008 Dodge Dakota
The headlight switch assembly on the dash of your 2008 Dodge Dakota does more then just turn the lights on and off; do not put off replacing a faulty switch. The switch controls the interior lights, the dash lights, parking or running lights and the headlights. A faulty switch will often cause other functions to fail; if the switch fails altogether, youll find yourself with no headlights at all and unable to drive your truck. Look for replacement switches at any auto parts retailer or your local Dodge dealer.
Instructions
- 1
Locate the retaining screws on the instrument panel of your Dakota, remove them with a Phillips screwdriver and set them aside. Pop the bezel off the instrument panel using a flat-blade screwdriver. Set the bezel aside for safekeeping.
2Locate the three retaining bolts on the face of the headlight switch assembly---two on the outboard edge and one on the inboard side---then remove them using a socket and ratchet. Set the bolts aside for reuse during installation.
3Slide the headlight switch assembly forward until you can reach the electrical connector on the rear of the assembly. Press the locking tab in on the connector, and separate the connector from the rear of the headlight switch. Pull the headlight switch out of the dash, and discard it.
4Slide the new headlight switch assembly into the dash far enough to allow the electrical connector to reach it. Push the connector onto the back of the switch, ensuring that the locking tab engages completely.
5Push the switch in place, and install the three retaining bolts. Tighten the bolts with a socket and ratchet until they are just snug enough to hold the switch securely but wont crack its plastic casing.
6Position the instrument panel bezel in place, snapping it into the retaining clips. Install the retaining screws and tighten them with a Phillips screwdriver only until they are just snug enough not hold the bezel in place without damaging it.
7Turn on the headlight switch, and cycle the headlights through the high- and low-beam positions several times to ensure a successful repair.
Monday, March 17, 2014
How to Turn Off Service Engine Soon Light on 2002 Ford Pickup
A 2002 Ford pickup is equipped with an On-Board Diagnostic II (OBD II) computer. This computer reads trouble codes sent from sensors positioned throughout the vehicle, and it keeps track of when the pickup needs to be serviced. When you see the Service Engine Soon light illuminate on your instrument panel, this is information being sent to you from the vehicles computer. Make sure you service the engine first before you attempt to reset and turn off the light. Otherwise the light will just keep turning back on and it wont accurately keep track of when your vehicle needs servicing.
Instructions
- 1
Lift up the hood of the pickup and prop it open. Remove the battery cable from the negative side of the battery using a 1/2-inch end wrench. Let the truck sit for about five minutes. Put the cable back in place and close the hood.
2Put the key into the ignition and start the engine. Look at your instrument panel to see if the Service Engine Soon light turned off. If it didnt turn off, go to an auto parts store and buy an OBD-II code scanner to reset the light.
3Plug the connector on the OBD-II code scanner into the port to the left under the steering column. Put the key into the ignition and turn the car on but dont start the engine. Key into your scanner your pickups make, model and engine size.
4Wait for the trouble code for Service Engine Soon to appear on the scanner. When it does, press "delete." Remove the scanner from the port and start the engine. The light should now turn off.
Friday, February 7, 2014
How to Reset the Engine Oil Light on a 2006 Chevy
The On-Board Diagnostics computer (OBD) in a 2006 Chevy has a maintenance light that turns on when your vehicle is ready for an oil change. You need to change the oil and manually reset the light. All you need to reset and turn off the light is a few moments of your time and your ignition key. Dont attempt to reset the light before you change the oil, as the computer wont be able to keep track of when your next oil change is due.
Instructions
- 1
Put the key in the ignition and turn it to "Run", but dont start the engine.
2Push down on the accelerator three times within five seconds. Make sure you press the pedal all the way to the floor each time. Examine the instrument cluster to see if the engine oil light is flashing. Let it flash until it stops, probably in about ten seconds.
3Turn off the vehicle and remove the key. Wait a minute, and then put the key back in the ignition and start the engine. Verify that the engine oil light has turned off. If it hasnt, repeat the process. You may have to press down harder and faster on the pedal.
Monday, February 3, 2014
How to Reset the Service Engine Light on a 2002 Mitsubitshi Eclipse
The 2002 Mitsubishi Eclipse has an On-Board Diagnostics system that monitors the vehicles emissions components and many of the vehicles mechanical aspects. When the "Service Engine" light illuminates on the instrument panel, you need to take your vehicle to a qualified mechanic for service before resetting the light. Otherwise, the computer wont be able to determine the next service date. Also, you will be erasing the trouble codes your mechanic needs to diagnose the problem.
Instructions
- 1
Find the diagnostic port on the Eclipse on the underside of the dashboard, near the drivers side. Plug the OBD code scanner into the port.
2Put the key in the ignition and turn the engine to the "On" position. Make sure you dont start the engine. This will power on the code scanner automatically.
3Wait for the OBD code scanner to run through its test. When it displays the trouble codes, write them on a piece of paper. Take the codes to your mechanic or look them up yourself in a repair manual. Unplug the code scanner and have the vehicle serviced.
4Repeat Steps 1 and 2. Wait for the trouble codes to appear. Press "Delete" or another similar button on your scanner. This will erase the codes and reset the light. Unplug the scanner from the port and turn off the vehicle.
5Turn on the engine and verify that the service engine light has turned off.
Friday, January 17, 2014
Instructions on Installing an Auxiliary Light Bar on a Harley Softail
Heritage Softails come equipped from the factory with a light bar. Well known aftermarket vendors like Kuryakyn and Harley-Davidson sell bolt-on auxiliary lighting for Softails. The extent to which extra lights brighten the road is open to debate. Many jurisdictions mandate that the extra light be turned off when the headlight is switched to high beam. But it is undeniable that the extra lights make the motorcycle brighter and make it, and the rider, easier to spot.
Instructions
EFI Fuel Tank Removal
- 1
Ride the motorcycle until the gas tank is almost empty.
2Pull off the electrical caddy cover, on the right side of the motorcycle, with your hands. Pull the fuel pump fuse out of the fuse array with a fuse puller.
3Run the engine until it dies. Push the starter button for another three or four seconds.
4Pull both ends of the quick connect fitting under the gas tank in opposite directions until the two halves of the fitting come apart.
5Loosen the screw that holds the rear fender and the seat together with a Phillips head screwdriver. Lift off the seat.
6Loosen the black battery cable with a combination wrench. Pull the cable from the negative terminal.
7Loosen and remove the nut in the middle of the instrument panel with an Allen socket and socket wrench. Pull the instrument panel up and pull the male and female halves of the fuel pump module connector apart.
8Plug the end of a short length of 5/16 inch diameter, rubber hose with a bolt of the same size. Secure the bolt in the hose with a hose clamp and a screwdriver.
9Place a 5 gallon gas can next to the motorcycle. Sever the clamp on either end of the crossover fuel line with metal shears.
10Pull the loose end of the crossover line off the tank fitting and immediately replace it the open end of the 5/16 inch hose. Drain the crossover line into the 5 gallon can.
11Clean up spillage with rags and remove the rags from the work location. Set the can aside.
12Unplug the crossover and vent lines from the bottom of the tank. Unbolt both the front and rear mounting bolts, washers and nuts with a combination wrench. Unplug the male and female halves of the fuel gauge wiring plug.
13Pull the tank off the motorcycle with your hands.
Auxiliary Lighting Installation
- 14
Attach the right and left light bar mounting clamps in the accessory lighting kit to the two fork tubes using the Allen screws in the kit and an Allen socket. Tighten both screws to 75 inch pounds of torque with the Allen socket and a torque wrench.
15Thread the wires from the accessory lights through the holes in the mounting brackets and fasten the lights to the brackets with the washers, retainers and clamp blocks included with the kit. Tighten the retainers of 19 pounds with an open end socket and torque wrench.
16Slip the inner nesting rings in the lighting kit onto the light bulbs in the kit. Lock the black wires to the black terminals next to the indexing tabs and the grey wires to the grey terminals.
17Install the accessory light bulbs into the chrome trim rings using the screws included with the kit and a screwdriver. Thread the light wires through the chrome tubes in the kit.
18Place the accessory lights wiring harness in the shallow pan that holds the seat. Stretch the longest wires along the backbone of the frame to the steering head.
19Remove the hex nut from the ground wire stud with a combination wrench. Slide the ground wire ring from the accessory lighting wiring harness onto the stud and replace the nut.
20Snap the white wiring harness connector into the "B" positive connector on the accessory lighting wire harness.
21Tie the accessory harness to the main wiring harness with the cable ties included with the accessory lighting kit.
22Stretch the longest wires in the auxiliary harness past the steering head. Route the light switch wires up the triple trees and across the left handlebar to the clutch lever cover.
23Disassemble the chrome, switch mounting bracket with a Torx driver, install the light switch and reassemble the mounting bracket.
24Remove the lower screw from the clutch lever housing with a Torx driver. Put the switch bracket tab over the hole and reinstall the screw. Tighten to 68 inch pounds using a torque wrench and Torx socket.
25Push the light switch wiring harness into the handlebar wiring retainers. Remove the trim ring from the headlight with a Phillips head screwdriver.
26Unplug the connector block from the headlight prongs. Unwrap the waterproof boot from the rear of the headlight.
27Squeeze and remove the retaining clip from the headlamp assembly. Twist the clip away from the headlamp and remove the headlamp bulb.
28Push the end of the light switch wire through the rubber ring in the headlight housing. Splice the switch wire to the yellow headlight wire using the crimp connecter in the lighting kit and a pair of pliers.
29Replace the headlight bulb in the headlight housing.
30Slip heat shrinkable tubing from the kit over the white wire in the accessory wiring harness. Strip the insulation from the end 1/4 inch of the two auxiliary lights power wires with a wire stripper.
31Splice all three wires with the three-way tube connector in the kit using a crimping tool. Cover the connector with the heat shrink tube and heat with a heat gun until the tube shrinks around the splice.
Final Assembly
- 32
Secure all loose wires with the clips included in the kit.
33Reattach the gas tank. Refuel the motorcycle.
34Reconnect the black battery cable. Replace the fuel pump fuse.
35Reattach the electrical caddy cover and seat.
Wednesday, December 4, 2013
How to Repair a Chevy 1998 1500 Pickup Backup Light
Repairing the backup lights on the rear of your 1998 Chevy Truck requires changing the bulbs. The backup lights provide clean, white light that allows you to see what is behind you when backing up the truck after dark. The lights also provide a way for other drivers to see you backing up. The bulb used in the backup lights of the Chevy is a 2057 and is available from parts retail stores.
Instructions
- 1
Open the tailgate of your Chevy and locate the two taillight retaining screws in the side of the bed where the tailgate would sit when closed. There is an upper and lower retaining screw on each taillight assembly.
2Remove the retaining screws from the taillight assembly with a Phillips screwdriver. Pull the taillight assembly straight out of the body. Locate the electrical connector on the rear of the assembly, press the locking tab down, and disconnect it from the assembly.
3Rotate the backup light bulb socket counterclockwise, and pull it out of the assembly. Pull the bulb straight out of the socket, and replace it with a new 2057 bulb. Slide the bulb socket into the rear of the assembly. Turn it clockwise to lock it in place.
4Connect the electrical harness connector to the taillight assembly. Slide the assembly into the body opening. Install the two retaining screws through the body and into the taillight. Tighten the screws with a Phillips screwdriver.
5Move to the opposite side of the truck and repeat the process if required. Close the tailgate.
Wednesday, November 27, 2013
How to Turn Off the Traction Control Light in a 2001 Jaguar 4 0
An illuminated traction control light in a 2001 Jaguar 4.0 is an indication that the ABS computer detects a problem with the traction control or anti-lock braking system. This could represent a current problem or a previous problem that has yet to be cleared from the ABS computers memory. An illuminated traction control light will remain on until the ABS computers memory is cleared and reset. In order to clear the computers memory and turn off the traction control light, a connection must be established between the ABS computer and an automotive scan tool. Once a connection is established, the memory can be cleared and the light will turn off automatically.
Instructions
- 1
Rotate the ignition switch to the OFF position in order to turn off the engine.
2Locate the Jaguars diagnostic communications interface port, or DCIP. The DCIP is mounted just out of side, underneath the dashboard, below the steering wheel. The port has 16 connection pins and is the male end that connects to the female end of the scan tool.
3Connect the female end of the scan tool to the male DCIP and turn the ignition switch to the ON position, then power on the scan tool.
4Enter the make, model and year of your vehicle when prompted by the scan tool. Search the menus using the navigation keys on the scan tool and enter the ABS computer menu. Choose the option to read the trouble codes from the ABS computers memory. Write down the trouble codes that display on the screen. These alphanumeric codes have a very high diagnostic value and can explain why the code was triggered, should the light re-illuminate once the codes are cleared.
5Choose the option to clear the codes from the computers memory. Once the memory is clear, the scan tool will indicate this on the main screen. Disconnect the tool and start the Jaguars engine. Confirm that the traction control light is now off.
Sunday, November 17, 2013
How to Replace a Fog Light on a 98 Grand Am
The 1998 Pontiac Grand Am fog light is under the front bumper cover. Replacing the fog light bulb is an easy task. To get to the back of the fog light assembly, you will need to get under the vehicle. If you have had the fog light on, let the vehicle sit at least ten to fifteen minutes before you start working on it. The fog light gets hot when it is on for a long time.
Instructions
- 1
Find a level place, jack up the vehicle, and place it on jack stands under the frame.
2Crawl under the vehicle and look straight up. You will see the back of the fog light assembly where the fog light bulb is mounted.
3Rotate the bulb counterclockwise and pull backward on the bulb to remove it. Disconnect the electric wire plug from the bulb.
4Connect the electric wire plug into the new bulb. Avoid touching the glass part of the bulb.
5Insert the new bulb in the hole in the back of the fog light assembly and rotate the bulb clockwise.
6Jack up the vehicle and remove the jack stands from under the frame and let the vehicle down. Turn the fog light on to make sure it works.
Sunday, November 3, 2013
How to Reset the Service Engine Soon Light on My 1997 Monte Carlo
If the "Service Engine Soon" light comes on inside the dashboard of your 1997 Monte Carlo, you can turn it off by disconnecting the battery. Service engine lights can come on inside of a car if you have recently changed an oxygen sensor in your fuel tank, for example. Dealerships and mechanics might tell you to drive the car for about 20 miles to clear the service engine light, but there is another way.
Instructions
- 1
Turn the car off. Pop the hood to your 1997 Monte Carlo, and locate the battery.
2Disconnect the red terminal from the battery with a socket wrench. Disconnect the black terminal from the battery with a socket wrench.
3Go to the ignition switch inside your Monte Carlo, and put your key inside. Turn the ignition switch three times. Turn the ignition switch to "OFF", and then reconnect the battery to the terminals.
4Turn the ignition switch to "ON" without starting the Monte Carlo. Leave the ignition switch on for one minute.
5Start the car and the "Service Engine Soon" light will be off.
Friday, November 1, 2013
How to Read a Saturn Service Light With a OBDII Reader
You can read your Saturns service light using an OBDII reader right from your own garage, saving yourself time and money. The Saturn has an On-Board Diagnostics (OBD) computer that notifies the driver of problems with the vehicle. It also alerts you to when you need to perform regular routine maintenance and service on your car. To find out exactly what type of servicing your Saturn needs, you can read the computer codes using an OBDII reader. These readers come with a booklet that translates the numerical codes, although some readers display the codes description on the devices screen.
Instructions
- 1
Put the key into the ignition and turn it to the "On" position. Do not start the engine.
2Locate an open port under the steering column near the fuse panel. Make sure its the same size and shape as the connective end on your OBDII reader. Plug the OBDII reader into this port. The Saturns electrical system will automatically power most OBDII readers.
3Wait for the device to read the codes. Look up the service codes in the booklet, if the description isnt displayed automatically on the readers display. Write down the code and description on a piece of paper.
4Unplug the reader and turn off the vehicle. Take your vehicle, and the code and description to your mechanic to have the vehicle serviced.
Monday, October 28, 2013
How to Reset the Service Light on a 2003 Nissan Sentra
Your 2003 Nissan Sentra comes equipped with an On-Board Diagnostics computer that keeps track of when your vehicle needs servicing and alerts you by illuminating the "service engine soon" light on the instrument panel. This light tells you that there may be a problem with the emission control system on the car. An auto-parts retailer can do a free diagnostic reading of the trouble code using a scanner. After you have diagnosed and fixed the problem, you can manually reset the light yourself.
Instructions
- 1
Pop up the hood of the car and locate the battery. The negative terminal has a black plastic covering. Find the negative battery clamp . Loosen the nut a bit using a 10 mm open-end wrench.
2Remove the clamp from the battery terminal. Take care not to let it touch the positive side of the battery or cable.
3Wait about 10 minutes, then reattach the negative battery cable to the negative side of the terminal and tighten the nut with the wrench.
4Put the key into the ignition and wait for the service light to flash on the instrument panel, then shut off the engine. The light is now reset.
Monday, October 21, 2013
How to Reset My 1995 Ford Windstar ABS Light
The anti-lock brake system (ABS) on the Ford Windstar is controlled by an ABS computer. This computer illuminates an ABS warning light on the instrument panel when there is a problem with the brakes. You can reset the ABS light on your 1995 Ford Windstar right from your home using an OBD code reader. This small, computerized device can be purchased from any auto parts store. Some stores will even loan you their code reader for free for the purpose of resetting the codes.
Instructions
- 1
Put the key into the ignition and turn it to the "On" position, taking care not to start the engine.
2Plug the code reader into the diagnostic port under the steering column on the dashboard, then turn the code reader on.
3Navigate through the code readers menu using the arrow keys. Select "ABS" then "Clear Codes" or similar type of command.
4Wait for the code reader to return to the main menu. This is an indication that the ABS code has been cleared.
5Unplug the code reader and start the engine. Check to see that the ABS light has shut off.
Monday, October 14, 2013
How to Reset the Engine Light on a Mazda B2200
When the "Check Engine" light illuminates on your Mazda, it is alerting you to a malfunction of a valve, sensor or solenoid on the vehicle. Whatever the cause, you need to have your vehicle looked at by a qualified mechanic. You or your mechanic can use an OBD diagnostic scan tool to retrieve the computers trouble codes so that the problem can be diagnosed accurately. Once the vehicle has been repaired, you can manually reset the Check Engine light yourself in just a few minutes, turning off the notice until another situation arises to cause the light to come on again.
Instructions
- 1
Put on your safety goggles and cloth work gloves.
2Open your B2200s hood and look for the battery. Attached to it are two cables; one is the negative cable. On the end of the cable attached to the battery is a clamp with a nut on it. Loosen that nut using the end wrench to disconnect the negative cable from the battery. Secure it so that it cannot come back into contact with the battery.
3Slip the cable clamp off the negative terminal, taking care not to let it touch the positive side of the battery. Wait at least five minutes.
4Put the negative battery cable clamp back on the negative battery terminal and tighten the nut.
5Put the key into the ignition and start the engine. Look on the instrument panel to make sure the Check Engine light has turned off.
Sunday, September 22, 2013
How to Reset a Dodge Engine Light
The check engine light illuminates on the control panel on the dashboard of your Dodge when the on-board diagnostic computer reads a trouble code from the engine. You should take your Dodge to a qualified mechanic to have the problem looked at and, if necessary, repaired before you reset the light. You can reset the light in a few minutes manually from home using a simple tool purchased from your local auto parts store. Or most auto parts stores will reset it for you for free.
Instructions
- 1
Locate and open the fuse panel cover on your Dodge. This is inside the vehicle on the bottom of the dashboard on the drivers side. Pull down on the cover from the top of the panel with your fingers.
2Locate an open port within the fuse panel that is the same size and shape as the connector end on your OBD scan tool. Plug the connector into the port.
3Put the key in the ignition and turn it on to the "II" position, which is right before the engine starts. Wait for the light that is flashing on the OBD scan tool to turn off. Look on the dashboard above the steering column to see that the check engine light has turned off as well.
Thursday, September 19, 2013
How to Reset the Oil and Engine Light on a BMW X5 2003 Using the Ignition
You can reset the oil and engine lights on your 2003 BMW X5 using the ignition key. Most people think you need to take your BMW to the dealership to have your car serviced and the lights reset, but you dont. Its a simple fix you can do right in your home garage. The Check Oil and Service Engine Soon lights illuminate on the vehicles instrument panel when the OBD, or on-board diagnostics, computer reads a trouble code sent from sensors positioned throughout the vehicle. Although you need to use an OBD scanner read the codes, you dont need one to reset the lights and turn them off.
Instructions
- 1
Sit in the drivers seat, close the door and fasten your seat belt.
2Press the odometer button with your left thumb while simultaneously putting the key into the ignition and turning it to the "Accessory" position.
3Keep pressing down on the odometer button until the light on the dashboard starts to flash and the word "Reset" appears.
4Let go of the odometer button, then push it in again and hold it.
5Let go of the button for the last time and look for five green lights to appear on the dash to let you know the system has been reset.
How to Reset an Oil Change Light on a 2002 Impala
The General Motors Oil Life Monitoring System measures the amount of usable life that is left in the motor oil since the last oil change as a percentage. The system calculates the oil life usage based on engine starts and the length of drive time, among other variables. This allows the owner to change the engine oil at just the right interval. The system either displays a percentage of remaining oil life, or will turn on a warning light when it is time for an oil change. The light must be reset manually when the oil is changed.
Instructions
- 1
Turn the ignition key to the "On" or "Acc" position. Turn off the radio before you attempt to perform the reset.
2Press the "Tune Disp" button on the radio. Hold the button in for at least five seconds. You should see the word "Settings" displayed. Press the "Seek Ptype" or "Seek Pscan" up or down arrow. This will let you scroll through the main menu.
3Scroll through the menu until "Oil Life" appears in the radio display. Push the "1 Prev" or "2 Next" button on the radio to enter the sub-menu. Press the "Seek Ptype" or the "Seek Pscan" up or down arrow to navigate through the menu. Scroll with these buttons until "Reset" appears on the display.
4Press the "Tune Disp" button to reset the oil life monitor. You will hear a chime that verifies that the reset is completed. "Done" will also show on the radio display for one second.
5Scroll using the radio buttons until you see "Exit" on the radio display. Press the "Tune Disp" button on the radio to end the programming. A chime will sound to let you know that you have exited.
Friday, September 6, 2013
How to Check the Engine Light on a 2000 Tacoma
The Tacoma is a compact pickup truck that Toyota has been manufacturing since 1995. You can read the codes pertaining to the "Check Engine" light on your 2000 Toyota Tacoma. The On-Board Diagnostics II (OBD II) computer receives trouble codes from various sensors positioned throughout the vehicle. It alerts you to any trouble codes pertaining to the emissions system or engine by illuminating the "Check Engine" light on your instrument panel. You can read these codes using an OBD II code reader. This computerized hand-held device can be purchased from any auto parts retailer. This is an easy job that should take about 10 minutes to complete.
Instructions
- 1
Find the DLC port on the drivers side dashboard under the steering column. Plug the connective end of the OBD II scan tool into this port. You may have to rotate it to make it fit. Make sure you dont force it in or it may bend the pins inside.
2Put the key into the ignition and turn it to the "On/Off" position. This powers on most scan tools. If not, find the power switch on the scan tool and turn it on.
3Select the "Read Codes" command on the scan tool. Wait for the scan tool to display the codes. Write the codes on a piece of paper and look up their meaning in the scan tools manual.
4Unplug the scan tool and turn off the vehicle. Have the necessary repairs made according to the codes diagnosis.