Pages

Showing posts with label installing. Show all posts
Showing posts with label installing. Show all posts

Friday, January 17, 2014

Instructions on Installing an Auxiliary Light Bar on a Harley Softail

Instructions on Installing an Auxiliary Light Bar on a Harley Softail

Heritage Softails come equipped from the factory with a light bar. Well known aftermarket vendors like Kuryakyn and Harley-Davidson sell bolt-on auxiliary lighting for Softails. The extent to which extra lights brighten the road is open to debate. Many jurisdictions mandate that the extra light be turned off when the headlight is switched to high beam. But it is undeniable that the extra lights make the motorcycle brighter and make it, and the rider, easier to spot.

Instructions

EFI Fuel Tank Removal

    1

    Ride the motorcycle until the gas tank is almost empty.

    2

    Pull off the electrical caddy cover, on the right side of the motorcycle, with your hands. Pull the fuel pump fuse out of the fuse array with a fuse puller.

    3

    Run the engine until it dies. Push the starter button for another three or four seconds.

    4

    Pull both ends of the quick connect fitting under the gas tank in opposite directions until the two halves of the fitting come apart.

    5

    Loosen the screw that holds the rear fender and the seat together with a Phillips head screwdriver. Lift off the seat.

    6

    Loosen the black battery cable with a combination wrench. Pull the cable from the negative terminal.

    7

    Loosen and remove the nut in the middle of the instrument panel with an Allen socket and socket wrench. Pull the instrument panel up and pull the male and female halves of the fuel pump module connector apart.

    8

    Plug the end of a short length of 5/16 inch diameter, rubber hose with a bolt of the same size. Secure the bolt in the hose with a hose clamp and a screwdriver.

    9

    Place a 5 gallon gas can next to the motorcycle. Sever the clamp on either end of the crossover fuel line with metal shears.

    10

    Pull the loose end of the crossover line off the tank fitting and immediately replace it the open end of the 5/16 inch hose. Drain the crossover line into the 5 gallon can.

    11

    Clean up spillage with rags and remove the rags from the work location. Set the can aside.

    12

    Unplug the crossover and vent lines from the bottom of the tank. Unbolt both the front and rear mounting bolts, washers and nuts with a combination wrench. Unplug the male and female halves of the fuel gauge wiring plug.

    13

    Pull the tank off the motorcycle with your hands.

Auxiliary Lighting Installation

    14

    Attach the right and left light bar mounting clamps in the accessory lighting kit to the two fork tubes using the Allen screws in the kit and an Allen socket. Tighten both screws to 75 inch pounds of torque with the Allen socket and a torque wrench.

    15

    Thread the wires from the accessory lights through the holes in the mounting brackets and fasten the lights to the brackets with the washers, retainers and clamp blocks included with the kit. Tighten the retainers of 19 pounds with an open end socket and torque wrench.

    16

    Slip the inner nesting rings in the lighting kit onto the light bulbs in the kit. Lock the black wires to the black terminals next to the indexing tabs and the grey wires to the grey terminals.

    17

    Install the accessory light bulbs into the chrome trim rings using the screws included with the kit and a screwdriver. Thread the light wires through the chrome tubes in the kit.

    18

    Place the accessory lights wiring harness in the shallow pan that holds the seat. Stretch the longest wires along the backbone of the frame to the steering head.

    19

    Remove the hex nut from the ground wire stud with a combination wrench. Slide the ground wire ring from the accessory lighting wiring harness onto the stud and replace the nut.

    20

    Snap the white wiring harness connector into the "B" positive connector on the accessory lighting wire harness.

    21

    Tie the accessory harness to the main wiring harness with the cable ties included with the accessory lighting kit.

    22

    Stretch the longest wires in the auxiliary harness past the steering head. Route the light switch wires up the triple trees and across the left handlebar to the clutch lever cover.

    23

    Disassemble the chrome, switch mounting bracket with a Torx driver, install the light switch and reassemble the mounting bracket.

    24

    Remove the lower screw from the clutch lever housing with a Torx driver. Put the switch bracket tab over the hole and reinstall the screw. Tighten to 68 inch pounds using a torque wrench and Torx socket.

    25

    Push the light switch wiring harness into the handlebar wiring retainers. Remove the trim ring from the headlight with a Phillips head screwdriver.

    26

    Unplug the connector block from the headlight prongs. Unwrap the waterproof boot from the rear of the headlight.

    27

    Squeeze and remove the retaining clip from the headlamp assembly. Twist the clip away from the headlamp and remove the headlamp bulb.

    28

    Push the end of the light switch wire through the rubber ring in the headlight housing. Splice the switch wire to the yellow headlight wire using the crimp connecter in the lighting kit and a pair of pliers.

    29

    Replace the headlight bulb in the headlight housing.

    30

    Slip heat shrinkable tubing from the kit over the white wire in the accessory wiring harness. Strip the insulation from the end 1/4 inch of the two auxiliary lights power wires with a wire stripper.

    31

    Splice all three wires with the three-way tube connector in the kit using a crimping tool. Cover the connector with the heat shrink tube and heat with a heat gun until the tube shrinks around the splice.

Final Assembly

    32

    Secure all loose wires with the clips included in the kit.

    33

    Reattach the gas tank. Refuel the motorcycle.

    34

    Reconnect the black battery cable. Replace the fuel pump fuse.

    35

    Reattach the electrical caddy cover and seat.

ReadMore

Wednesday, November 27, 2013

DIY Installing a Fender Vent

The fender vent on any vehicle is simply cosmetic. Mechanically, these vents do not serve a purpose on your vehicle. If you would like to install a new fender vent, you can do it with little hassle and minimal knowledge of the automobile. If you do remove the fender vent and do not replace it, you will leave holes in the fender and the vehicle will look like it is missing something. Since this is a stick-on piece, you have a limited time frame and getting it level before the adhesive becomes hard.

Instructions

    1

    Park your vehicle in a well lit area so the back fender is getting enough light. Turn off the automobile so there is no chance of it moving while you are working on it.

    2

    Use a plastic wedge to get between the fender and the edge of the vent. If you use a flathead screwdriver, you could scratch the paint.

    3

    Edge your way around the vent until you loosen it from the adhesive. Pull the vent off of the fender.

    4

    Add the adhesive to the new fender vent. Make sure that you are not using too much adhesive as it will come out the sides of the vent and adhere to the fender creating a mess.

    5

    Apply the vent to the fender in the same position as your last vent. Back up after the vent has been installed. Correct any crookedness to the vent, if needed.

    6

    Use a rag to wipe up any excess adhesive coming off of the vent.

ReadMore

Sunday, November 10, 2013

Installing a Fuel Pump on a 97 Chrysler Sebring LXi

Installing a Fuel Pump on a 97 Chrysler Sebring LXi

Like the first generation of Sebring Convertibles, the 1997 Chrysler Sebring LXI has a Mitsubishi 2.5L V6 engine with fuel injection. The fuel-injection system operates under very high pressure supplied from the gas tank by the fuel pump. Replacing the fuel pump on the LXI is a different procedure than other Sebring models, but fortunately, is well within the capabilities of even a novice mechanic.

Instructions

    1

    Relieve fuel tank pressure by opening the gas filler cap. Inside the car, pull upward on the rear seat cushion to disengage it from its retaining hooks and remove the cushion from the vehicle. Of the two access panels underneath the cushion, remove the one on the right.

    2

    Disconnect the wiring harness that attaches to the fuel pump. Turn the ignition and allow the engine to run until it dies from a lack of fuel system pressure. This permits safe removal of the fuel pump. Once the fuel pressure has been released, disconnect the negative battery cable.

    3
    Keep a fire extinguisher on hand to deal with any accidental fires.
    Keep a fire extinguisher on hand to deal with any accidental fires.

    Remove the hose connecting the fuel pump to the fuel rail. Remove the mounting bolts holding the fuel pump in place and lift the pump out of the fuel tank. Wrap the pump in shop towels to catch remaining gasoline and relocate the pump to a well-ventilated area.any

    4

    Place the new fuel pump into the fuel tank by carefully aligning the pump with the slots in the tank until the pump is securely seated. Reinstall the mounting bolts (22 inch-pounds of torque) and reconnect the hose leading to the fuel rail. Reinstall the access panel and seat cushion.

    5

    Make sure that the gas filler cap has been reinstalled and reconnect the negative battery terminal. Turn the ignition to the "On" position for a few seconds to allow the fuel system to build pressure, then start the engine to confirm proper operation.

ReadMore

Thursday, October 10, 2013

Installing Sway Bar Links on a 1998 Caravan

Installing Sway Bar Links on a 1998 Caravan

The sway bar links of a 1998 Dodge Caravan connect the front struts to the sway bar. The sway bar transmits torque across the minivan from one side to the other. When cornering, the weight of the Caravan shifts to the outside of the turn, compressing the strut more on one side than the other. The pressure is transmitted through the way bar links to the sway bar, placing pressure on the opposite strut. This reduces roll and stabilizes the 1998 Caravan. The sway bar links have ball and socket designs. Over time, the socket wears and a clunking noise emits from the sway bar link. Eventually, the stabilizer link will break if it is not replaced.

Instructions

    1

    Park the 1998 Dodge Caravan on a level flat surface and set the parking brake. Lift the front of the vehicle with an automotive floor jack. Place jack stands under both sides of the front of the vehicle under the subframe.

    2

    Remove the lug nuts using a lug nut socket and impact wrench. Remove the tires.

    3

    Remove the nuts attaching the sway bar link. The sway bar links attach with a stud and nut at both the front strut and the front sway bar. Place a wrench on the nut first. Use a small 8 mm wrench to prevent the stud from spinning while loosening the nut. Repeat for the second nut. Repeat for the opposite side.

    4

    Position the sway bar links. Install and tighten the nuts. Use the double wrench setup to prevent the stud from turning as you torque the nut.

    5

    Reinstall the tire. Install the lug nuts finger tight.

    6

    Raise the vehicle with the automotive floor jack. Remove the jack stands. Lower the vehicle.

    7

    Torque the lug nuts using the 1/2-inch lug nut socket and 1/2-inch drive torque wrench to 100 foot-lb. torque.

ReadMore

Wednesday, October 2, 2013

Installing an Exhaust Manifold on a Jeep Grand Cherokee

Installing an Exhaust Manifold on a Jeep Grand Cherokee

Preparation

    Before the exhaust manifold on a Jeep Grand Cherokee can be installed, the vehicle must be prepped. The battery and air cleaning assembly, including the filter, must be removed; and all coolants, such as windshield cleaning solution and radiator fluid, should be drained and flushed from the system. Disconnect the air-conditioner and detach the starter motor and all heating hoses. You are removing them to gain access to the cylinder head.

Removing Existing Parts

    Remove the manifold by, first, taking out the heat-shield components and disconnecting the starter motor. Detach the Y-pipe, and unbolt and lift out the manifold, along with the gasket between the unit and the engine. Rusty bolts and fasteners are usually treated and cleaned before the new manifold is installed.

Installation

    Before the exhaust manifold is attached to the cylinder head, covering all six cylinders, position the manifold gasket over the edge of the opening. Then set the manifold into place over the gasket. Tighten the bolts, starting in the center and moving toward the ends, and reconnect the unit to the Y-pipe. Reinstall the disassembled parts in the opposite order in which they were removed.

ReadMore