Pages

Showing posts with label softail. Show all posts
Showing posts with label softail. Show all posts

Monday, November 17, 2014

How to Install a Driving Light on a Harley Davidson Softail

How to Install a Driving Light on a Harley-Davidson Softail

Harley-Davidson driving lights mount on the front forks of Softails. The driving lights may add slightly to your view of the road at night. They add significantly to the recognition by oncoming drivers that you are there. The pattern formed by a headlight and two driving lights is conspicuous, and driving lightbulbs are often yellow, so even drunks are inclined to slow down when they see you coming. The popular Heritage Softail Classic, styled to look like a mid-60s hog, comes equipped with three lights as standard equipment. If that is the effect you are trying to achieve, numerous aftermarket vendors, including Harley and Kuryakyn, sell driving light kits. These instructions are specific to recent, fuel-injected Softails.

Instructions

Remove Fuel Tank

    1

    Remove the electrical caddy cover by pulling on it with both hands. Pry the fuel pump fuse out of the electrical caddy with a small, flathead screwdriver.

    2

    Start the engine in neutral and run the engine until it dies. Run the starter for four more seconds.

    3

    Disconnect the fuel supply line by pulling up on the chrome sleeve of the fuel tank quick-connect fitting and pulling down on the fuel supply line.

    4

    Unscrew the bolt that secures the seat tab to the rear fender. Recent Softails use a Phillips screw, which must be removed with a screwdriver. Older Softails use an Allen bolt, which comes off with an Allen wrench.

    5

    Remove the seat to access the battery compartment. Disconnect the negative battery wire from the negative terminal with an open-end wrench.

    6

    Remove the instrument panel by loosening and removing the acorn nut on the panel with an Allen wrench and pulling up. Unplug the fuel pump module connector under the instrument panel.

    7

    Push a 5/16-inch-diameter bolt in one end of a foot long piece of 5/16-inch rubber hose. Tighten a hose clamp around the hose and the bolt with a flathead screwdriver.

    8

    Cut the hose clamp from one end of the crossover hose with side blade pliers. Very quickly replace the crossover hose on the fuel tank fitting with the open end of the 1-foot hose while directing the flow of gasoline from the free end of the crossover hose into an adequately sized gas can.

    9

    Clean up spilled gasoline with rags. Carry the rags outside if you are working in a garage.

    10

    Disconnect the crossover hose and the continuous venting vent line. Remove the front tank mounting bolt, flat washers and acorn nut with an open-end wrench.

    11

    Remove the rear mounting bolt, flat washers and nut with an open-end wrench. Disconnect the fuel gauge connector under the left side of the fuel tank with your hands.

    12

    Lift the tank straight up to remove. Set the tank on a well-padded surface in a well-ventilated place.

Install Lights

    13

    Install the left-hand and right-hand side specific mounting clamps that came with the driving light kit on the right and left fork tubes using the four buttonhead screws that came with the driving light kit. Tighten the screws to between 70 and 80 inch-pounds of torque with an Allen socket and a torque wrench.

    14

    Route each lamp wire through the hole in each mounting bracket and secure the lamp to each bracket using a clamp block, lock washer and retainer from the kit. Tighten the retainer to 18 foot-pounds of torque with an open-end socket and a torque wrench.

    15

    Position the inner nesting rings from the kit on each lightbulb. Connect the black wires to the bulb spade terminals next to the bulbs indexing tabs. Install the gray wires on the remaining spade terminals.

    16

    Attach the bulbs and the inner nesting rings to the outer trim rings with the Phillips screws included in the kit. Slide the conduit tubes from the kit over both lamp wires.

    17

    Set the light kit wiring harness relay in the seat pan. Route the long leg of the harness along the frame spine under the seat.

    18

    Plug the white wire connector into the "B+" connector on the lighting kit wiring harness. Loosen and remove the nut on the ground wire stud in the seat pan with a socket wrench and socket.

    19

    Slip the black, ground wire ring over the ground wire stud. Replace the ground wire stud nut. Secure the driving light kit wire harness to the adjacent wiring harnesses with the cable straps included in the driving light kit.

    20

    Route the driving light wiring harness past the steering head. Route the lamp switch leg of the harness along the left side of the handlebar to the clutch control.

    21

    Unscrew the boot from the small lamp switch in the kit. Install the switch into the switch mounting bracket in the kit and replace the boot on the switch.

    22

    Remove the lower screw and washer from the clutch control clamp with a Torx driver. Position the tab of the driving light switch bracket over the screw hole and replace the Torx screw and washer. Tighten the screw to 70 inch-pounds of torque with a Torx socket and torque wrench.

    23

    Loosen the headlight trim ring clamp with a Phillips screwdriver. Remove the headlight trim ring.

    24

    Pull the connector block from the headlight bulb prongs. Remove the rubber boot from the back of the headlight lens.

    25

    Squeeze the wire retaining clip ends to unhook them from the notches in the headlight assembly. Pivot the wire retaining clip away from the headlight bulb and remove the bulb from the headlight assembly.

    26

    Route the unconnected wire from the handlebar switch through the grommet into the headlight housing. Splice that wire to the yellow (low-beam) headlight wire using the electrical connector included in the driving light kit.

    27

    Reinstall the headlight bulb.

    28

    Slide the heat-shrink tubing included in the kit over the white wire in the driving light wiring harness. Strip the ends of both lamp wires with a wire stripper.

    29

    Splice the white wire to the lamp wires with the three wire connector included in the kit with a wire crimping tool. Cover the splice with the heat shrink tubing and shrink the tubing with a heat gun.

    30

    Clip the driving light wires to the lower fork steering bracket using the adhesive-backed clips from the kit.

    31

    Reinstall the fuel tank. Reconnect the negative battery cable.

    32

    Reinstall the fuel pump fuse. Replace the electrical caddy cover. Replace the seat.

ReadMore

Friday, January 17, 2014

Instructions on Installing an Auxiliary Light Bar on a Harley Softail

Instructions on Installing an Auxiliary Light Bar on a Harley Softail

Heritage Softails come equipped from the factory with a light bar. Well known aftermarket vendors like Kuryakyn and Harley-Davidson sell bolt-on auxiliary lighting for Softails. The extent to which extra lights brighten the road is open to debate. Many jurisdictions mandate that the extra light be turned off when the headlight is switched to high beam. But it is undeniable that the extra lights make the motorcycle brighter and make it, and the rider, easier to spot.

Instructions

EFI Fuel Tank Removal

    1

    Ride the motorcycle until the gas tank is almost empty.

    2

    Pull off the electrical caddy cover, on the right side of the motorcycle, with your hands. Pull the fuel pump fuse out of the fuse array with a fuse puller.

    3

    Run the engine until it dies. Push the starter button for another three or four seconds.

    4

    Pull both ends of the quick connect fitting under the gas tank in opposite directions until the two halves of the fitting come apart.

    5

    Loosen the screw that holds the rear fender and the seat together with a Phillips head screwdriver. Lift off the seat.

    6

    Loosen the black battery cable with a combination wrench. Pull the cable from the negative terminal.

    7

    Loosen and remove the nut in the middle of the instrument panel with an Allen socket and socket wrench. Pull the instrument panel up and pull the male and female halves of the fuel pump module connector apart.

    8

    Plug the end of a short length of 5/16 inch diameter, rubber hose with a bolt of the same size. Secure the bolt in the hose with a hose clamp and a screwdriver.

    9

    Place a 5 gallon gas can next to the motorcycle. Sever the clamp on either end of the crossover fuel line with metal shears.

    10

    Pull the loose end of the crossover line off the tank fitting and immediately replace it the open end of the 5/16 inch hose. Drain the crossover line into the 5 gallon can.

    11

    Clean up spillage with rags and remove the rags from the work location. Set the can aside.

    12

    Unplug the crossover and vent lines from the bottom of the tank. Unbolt both the front and rear mounting bolts, washers and nuts with a combination wrench. Unplug the male and female halves of the fuel gauge wiring plug.

    13

    Pull the tank off the motorcycle with your hands.

Auxiliary Lighting Installation

    14

    Attach the right and left light bar mounting clamps in the accessory lighting kit to the two fork tubes using the Allen screws in the kit and an Allen socket. Tighten both screws to 75 inch pounds of torque with the Allen socket and a torque wrench.

    15

    Thread the wires from the accessory lights through the holes in the mounting brackets and fasten the lights to the brackets with the washers, retainers and clamp blocks included with the kit. Tighten the retainers of 19 pounds with an open end socket and torque wrench.

    16

    Slip the inner nesting rings in the lighting kit onto the light bulbs in the kit. Lock the black wires to the black terminals next to the indexing tabs and the grey wires to the grey terminals.

    17

    Install the accessory light bulbs into the chrome trim rings using the screws included with the kit and a screwdriver. Thread the light wires through the chrome tubes in the kit.

    18

    Place the accessory lights wiring harness in the shallow pan that holds the seat. Stretch the longest wires along the backbone of the frame to the steering head.

    19

    Remove the hex nut from the ground wire stud with a combination wrench. Slide the ground wire ring from the accessory lighting wiring harness onto the stud and replace the nut.

    20

    Snap the white wiring harness connector into the "B" positive connector on the accessory lighting wire harness.

    21

    Tie the accessory harness to the main wiring harness with the cable ties included with the accessory lighting kit.

    22

    Stretch the longest wires in the auxiliary harness past the steering head. Route the light switch wires up the triple trees and across the left handlebar to the clutch lever cover.

    23

    Disassemble the chrome, switch mounting bracket with a Torx driver, install the light switch and reassemble the mounting bracket.

    24

    Remove the lower screw from the clutch lever housing with a Torx driver. Put the switch bracket tab over the hole and reinstall the screw. Tighten to 68 inch pounds using a torque wrench and Torx socket.

    25

    Push the light switch wiring harness into the handlebar wiring retainers. Remove the trim ring from the headlight with a Phillips head screwdriver.

    26

    Unplug the connector block from the headlight prongs. Unwrap the waterproof boot from the rear of the headlight.

    27

    Squeeze and remove the retaining clip from the headlamp assembly. Twist the clip away from the headlamp and remove the headlamp bulb.

    28

    Push the end of the light switch wire through the rubber ring in the headlight housing. Splice the switch wire to the yellow headlight wire using the crimp connecter in the lighting kit and a pair of pliers.

    29

    Replace the headlight bulb in the headlight housing.

    30

    Slip heat shrinkable tubing from the kit over the white wire in the accessory wiring harness. Strip the insulation from the end 1/4 inch of the two auxiliary lights power wires with a wire stripper.

    31

    Splice all three wires with the three-way tube connector in the kit using a crimping tool. Cover the connector with the heat shrink tube and heat with a heat gun until the tube shrinks around the splice.

Final Assembly

    32

    Secure all loose wires with the clips included in the kit.

    33

    Reattach the gas tank. Refuel the motorcycle.

    34

    Reconnect the black battery cable. Replace the fuel pump fuse.

    35

    Reattach the electrical caddy cover and seat.

ReadMore