Saturday, June 7, 2014
How to Change the Time in an 03 Passat
The 2003 Volkswagen Passat, including the GL, GLS, GLX and W8 4motion, features several standard and optional convenience options. All models include a liquid crystal display clock on the instrument cluster below the tachometer. Changing the time is an easy task that does not require any special tools or automotive knowledge.
Instructions
- 1
Turn the ignition switch to the RUN or ACC position.
2Examine the instrument panel and locate the digital clock display.
3Take note of the correct time, using a watch or cell phone.
4Turn and hold the small plastic knob below the tachometer, using a counterclockwise motion to incrementally increase the hours. Release the knob when the correct hour is displayed.
5Turn and hold the knob clockwise to adjust the minutes. Release the button when finished.
6Turn the ignition to the OFF position to complete the process.
Tuesday, May 20, 2014
How to Calculate an Intake Runner
An engines induction system can be designed to improve the location of peak torque within its RPM range by altering the intake manifolds plenum volume, runner length and runner diameter. Long and narrow intake runners will result in lower RPM ratings, while short and wide runners will result in higher RPM ratings. Determining the RPM rating at which you want peak torque to occur is up to you, but once you do decide, calculating the intake runner size is straightforward.
Instructions
Calculating Intake Runner Diameter
- 1
Decide the RPM rating at which you want peak torque to occur. For example, youd like your cars engine to reach 5,000 RPM at peak torque.
2Multiply the RPM rating from Step 1 by the engines displacement volume and volumetric efficiency. For example, the cars engine has a displacement of 1.5 liters and a volumetric efficiency of 95 percent. Multiplying 5,000 by 1.5 by 0.95 equals 7,125.
3Divide the result from Step 2 by 3,330. In the example, 7,125 divided by 3,330 equals 2.140.
4Calculate the square root of the result from Step 3 to determine the intake runners diameter. In the example, the square root of 2.140 is 1.463. The intake runners diameter should be 1.463 inches.
Calculating Intake Runner Length
- 5
Subtract the result from Step 1, Section 1 from 10,000. In the example, subtracting 5,000 from 10,000 equals 5,000.
6Divide the result from Step 1 by 1,000. In the example, dividing 5,000 by 1,000 equals 5.
7Multiply the result from Step 2 by 4.3. In the example, multiplying 5 by 4.3 equals 21.5.
8Add 17.8 to the result from Step 3 to calculate the intake runner length in centimeters. In the example, adding 17.8 to 21.5 equals 39.3 cm.
9Multiply the result from Step 4 by 0.3937 to convert the intake runner length to inches. In the example, multiplying 39.3 by 0.3937 equals 15.472. The intake runner should be 15.472 inches long.
Wednesday, May 14, 2014
Specifications of an NV3500 Transmission
The NV3500 is a five-speed manual transmission found in General Motors and Chrysler trucks.
The manufacturer, New Venture Gear, is a company that was formed through the merger of the manual transmission engineering and manufacturing divisions of GM and Chrysler.
Design
The NV3500 is a fully synchronized, constant mesh transmission. The clutch housing, or bell housing, is an integral component to the transmission and is not meant to be removed. According to DodgeRam.org, the NV3500 "has a single shaft shift mechanism with all three shift forks mounted on the shaft."
Variations
The HM290 model, found in GM trucks beginning in 1988, was the forerunner of the NV3500-series transmission. This unit, and the 560 which superseded it, have four shift rails. When this transmission was re-engineered as the NV3500, a single shift rail was used in the design.
There are many design variations of the NV3500, each with unique parts. Two-wheel drive and four-wheel drive variants are available. Another variant is the NV3500HD.
Model Lines
The NV3500 transmission was deployed in the full-size half-ton Chevrolet Silverado and GMC Sierra pickups, Chevrolet S10 and GMC S15 trucks beginning in 1990, and some Dodge Dakota trucks beginning in the 1994 model year.
In the Dakota, the NV3500 is used with V-8 engines including the 3.9-liter and 5.2-liter Dodge powerplants.
Hauling Capacity
According to DodgeRam.org, the NV3500 is rated to a maximum GVWR of 7,200 lbs. and a maximum GCVWR of 11,000 lbs. The NV4500 transmission, built for larger engines, is a heavy-duty transmission for trucks that require greater hauling and towing capabilities.
Tuesday, May 13, 2014
What Does an EGR Valve Do in a Mercury Sable
The exhaust gas recirculation valve, or EGR valve, is part of the Mercury Sables emissions control systems. EGR valves, which were introduced in the 1970s, are now included on all automobiles in the United States.
Purpose
The EGR valve, usually located on the intake manifold, reduces oxides of nitrogen (NOx) that form in internal combustion engines when temperatures reach 2,500 degrees Fahrenheit or more. Nitrogen and oxygen combine to form NOx, a component of smog.
Function
As its name implies, the EGR valve recirculates exhaust gases back into the combustion chamber. Because the exhaust gases cannot be burned again, the result is cooler temperatures in the combustion chambers---several hundred degrees cooler. This reduces the production of NOx.
Performance
The creation of the EGR valve has enabled auto engineers to design more aggressive timing for engines, increasing efficiency and, as a result, improving fuel economy. A malfunctioning EGR valve, however, leads to engine ping and knocking.
Monday, May 12, 2014
How to Upholster an Automobile Interior
Older cars often have outdated, torn, or stained interiors. Reupholstering the automobile doors and seats will give your car a new look. The most difficult part of upholstering an automobile is the preparation. In order to reupholster the automobile seats they must be removed. Similarly, you will need to remove the door panel before you can reupholster it with new fabric. Choose an upholstery fabric that is durable and easy to work with. It is especially important to choose a fabric that will not scar if you unpick a seam and have to re-sew it.
Instructions
- 1
Take the automobile seats out from the car with a socket wrench. Set the seats on a flat surface that has plenty of room to work.
2Remove the hog seams and listing wires from the seats. Lift the upholstery from the seats.
3Cut apart the upholstery with a seam ripper. Only cut the seams between the pieces of upholstery fabric so that you can use the old pieces as templates for the new upholstery. Mark or label each piece of the fabric so you know how to piece the new upholstery together.
4Place the old pieces of upholstery on top of a length of laid out upholstery fabric. Trace around each piece of upholstery on the new fabric with a piece of chalk or a marker.
5Cut out the traced marks on the new upholstery fabric with scissors.
6Piece together the pieces of the cut out upholstery fabric. Match up the appropriate edges and sew them together with a inch straight stitch seam. Sew together the entire set of cut out upholstery pieces.
7Place the sewn together upholstery on the automobile seats. Replace the listing wires and hog rings in the automobile seats.
8Set the car seats back into the car. Secure the seats with a socket wrench.
Wednesday, May 7, 2014
How to Repair an Automobile Sunroof
If you have a vehicle with a sunroof, repairing it when it breaks is a necessity to keep elements from getting into the car. In many cases, a repair may not work, and you will have to take it to a dealer to completely replace it. Reasons for replacing it completely would be a problem in the actual motor of the sunroof not working properly, or in some cases a break in other internal hardware that cannot be reached with a simple repair kit. In some scenarios, repairing it can be the solution.
Instructions
- 1
Choose the model of sunroof that fits your car. There are sunroof kits available at your auto parts store that will correspond to the make and model of your car.
2Place the template that comes with the sunroof kit unto the top of your sunroof. The template will help you see what the problems could be. The kit will also include manufacturers directions; read through them thoroughly.
3Crank the sunroof open with a socket wrench little by little so you can isolate exactly where the sunroof is broken.
4Remove the broken part of the sunroof and use your manufacturers kit to replace it. The manufacturers kit will have different components to use to replace broken parts. Use the manufacturers directions for specific information on replacing the part.
5Test to make sure that parts have been installed correctly by cranking with the socket wrench slowly until the roof recedes back down. You can also test for leaks by gently squeezing water and looking at the underside to see if it is seeping through.
Monday, May 5, 2014
Components for an Automatic Choke
An automatic choke can be located on the carburetor of an engine, or it can be located a short distance from the carburetor and is called a "divorced" or "remote choke." The choke is important in the operation of a gasoline engine because it restricts the flow of air passing into an engine when the engine is cold; it could struggle to start with less gasoline flowing into the engine.
Automatic Choke
The automatic choke is an important part of a gasoline engine, working in tandem with the carburetor to restrict and increase the flow of air flowing into the engine. The automatic choke can be briefly described as a valve that closes to restrict the flow of air when the engine is cold. As the engine heats up, the automatic choke slowly opens the valve to allow more air to flow into the engine and reduce the amount of gasoline passing into the engine. The choke system of an engine, such as that for an automobile, is recognized as part of the transmission system.
Coil
In general, automatic chokes use a bimetallic coil to operate the choke plate valve system for increasing and reducing the amount of air passing into an engine. The bimetallic coil rotates when it is cold to close the choke plate and stop the passage of air that can mix with gasoline; this is to allow a larger amount of gasoline to arrive in the engine as required when the engine is cold. As the engine heats up, a vacuum forms that pulls the bimetallic coil back from the choke releasing the pressure and allowing more air to mix with the gasoline in the engine.
Types
Although the automatic choke system works in much the same way in integral and divorced systems, the remote automatic choke is housed in the engine manifold instead of attached to the carburetor. Remote automatic chokes use a separate choke pull off system, while integral systems use a tiny vacuum system linked to the throttle to operate a piston to open the automatic choke.
Rods
In repairing automatic choke systems the incorrect thickness of carburetor used can result in problems with the rods used to open and close a divorced system either not completely closing or opening the choke system. Where the automatic choke system is not working correctly, such as the vacuum passageway used by integral systems being clogged, the choke system may not allow the engine to start or operate effectively.
Friday, May 2, 2014
How to Ship an Exhaust System
Vehicle exhaust systems consist of multiple parts. In order to properly ship the entire exhaust system, you will need to ship the components separately to avoid damaging them, being sure to keep your packaging to a reasonable size and weight in order to minimize shipping costs. Packing and shipping a car exhaust can be done relatively quickly. As long as it is packaged properly, the parts should reach your recipient in good condition.
Instructions
- 1
Prepare the exhaust components for packaging. There is a very small market for used car exhausts, so most exhaust systems will be brand new when they are shipped and you should not have to worry about cleaning the parts before shipping them.
2Wrap each part in several layers of soft towels to protect them during shipping. Exhaust parts such as the muffler and exhaust manifolds are heavy enough that they may not be fully protected by bubble wrap.
Ship each component of the exhaust system separately to avoid the pieces moving and damaging one another during shipping.
3Locate boxes to ship the exhaust in. Found Value recommends shipping long exhaust parts in five-foot long wardrobe boxes. If any of the parts are unusually heavy, you can purchase specially made double-walled shipping boxes that are twice as strong as regular cardboard boxes.
4Fill your cardboard boxes with packing peanuts and place each exhaust system part in an individual box. Once you have placed each part into its box, place your packing slip into one of the boxes and then seal the boxes with packing tape.
5Ship the exhaust using a shipper that regularly deals with large boxes and heavy items. You may want to check with different shippers for possible discounts or promotions. You also may want to select ground shipping for the exhaust system. Ground shipping is less expensive than air, and exhaust parts often cost more to ship because of their size.
Monday, April 28, 2014
How to Replace an Exhaust Catalytic Converter
The catalytic converter happens to be one of the most expensive parts of a car to fix, which leads many people to try to repair it at home. You have to know your way around cars and exhaust systems, or youre honestly better off taking it to a mechanic. If youre comfortable working on it yourself, there are a few things you should keep in mind.
Instructions
- 1
Lift your car. Unfortunately, the catalytic converter sits about midway down the length of your car, so lifting one end or the other will not do. Ramps are your best bet to get you within reach of the parts when working from home. Luckily, this is usually the hardest part of this repair.
2Be patient with the bolts, as they are often hard to remove due to size and awkward placement. You may have to drill or saw bolts to remove them. With this in mind, you should pick up new bolts, nuts and seals for your replacement project.
3Buy a catalytic converter specific to your car to avoid extra work. A generic part must be welded into the car, while a vehicle-specific model comes pre-welded to the proper pipes for easy bolt-on installation.
4Remove the 02 sensor (with an O2 wrench) before unbolting the catalytic converter. Then, you should remove the pipe connecting the sensor to the converter. Depending on your exhaust system, you may have to remove more pipes before you unbolt the converter from the muffler.
5Replace the old catalytic converter with a new one. This should be the easy part, as you simply bolt the new part in place.
6Reattach the exhaust pipes and 02 sensor, and the basic job is done. Make sure you replace any cracked or rusty pipes while you have the exhaust system apart.
Friday, April 25, 2014
How to Clear a Service Engine in an Acura
Your Acura generates and stores fault codes whenever there is a problem with a solenoid, valve or sensor. This will show up on your instrument panel as "Service Engine" or other warning light. Once you have the codes checked and the vehicle serviced by a qualified mechanic, you need to clear the codes. Usually the mechanic can and will do this, but not always. Not only is it annoying to have the light remain on your instrument panel, it is also bad for the vehicles computer, which may not able to keep track of when your next servicing is due. You dont need any special tools to clear the service engine light on your Acura. Its a relatively easy fix.
Instructions
- 1
Put the key into the ignition and turn the engine to the "off" position on your Acura.
2Find the reset button on the odometer located on the instrument panel. Press and hold this button while simultaneously turning the key in the ignition to the on or "II" position.
3Hold the button for about 10 to 15 seconds, then release it. The "service engine soon" light will go out.
4Turn off the vehicle, then turn the engine on. Verify that the "service engine soon" light is still off.
Friday, April 18, 2014
How to Fix an Oxygen Sensor for a Volkswagen Passat
The Volkswagen Passat oxygen sensor controls the amount of fuel burned by the engine. If the oxygen sensor is failing, the car will run rich, burning extra fuel and decreasing your fuel mileage. Volkswagen secures the wiring for the oxygen sensor using cable ties to prevent damage to the electrical wires from the exhaust pipe. When an oxygen sensor fails, it must be replaced. Find a new sensor at an auto parts store or Volkswagen dealer.
Instructions
- 1
Raise the front end of your Volkswagen Passat and secure it on a set of jack stands. Remove the jack when the jack stands are secure to provide room to work.
2Locate the oxygen sensor between the manifold and the catalytic converter. The sensor will be protruding from the exhaust pipe with an electrical connection at the top. Pull the wiring harness free of the electrical connection.
3Remove the cable ties on the harness, making note of where they go. You will need to replace the cable ties in the same locations to protect the wiring from exhaust damage.
4Remove the oxygen sensor from the exhaust pipe using an oxygen sensor socket and a ratchet. Replace the sensor with a new one. Thread the new sensor in by hand to start so you do not cross thread the sensor. Tighten it with an oxygen sensor socket and ratchet.
5Torque the oxygen sensor to 41 foot-pounds with a torque wrench.
6Replace the cable ties on the wiring and reconnect the wiring harness to the electrical connection on the sensor.
7Raise the car and remove the jack stands. Lower the car to the ground.
Tuesday, April 15, 2014
How to Remove a Head From an F 250
The Ford "F" series of full-size pickups use the model number to indicate the rated carrying capacity of the vehicle. For example, an F-250 has a payload capacity of about 2500 pounds, and newer models can carry more than this. The standard engine options for the F-250 include 5.4-liter and 6.8-liter gasoline engines. These engines have two cylinder heads, each covering half of the cylinders. The procedure for removing the cylinder heads is generally the same for all F-250 trucks made since 2001 with gasoline engines.
Instructions
- 1
Remove the air conditioner from the vehicle to access the cylinder heads on top of the engine block. This generally requires a professional mechanic with special equipment to avoid releasing rigerant gas into the atmosphere.
2Disconnect the cable from the negative battery terminal with a socket wrench to ensure the engine does not start accidentally. Remove the covers for the cylinder heads.
3Remove the intake manifold from the engine block with a socket wrench. Disconnect the timing chains from their sprockets. Remove the exhaust manifolds from the engine.
4Disconnect the two retaining bolts for the heater hose with a socket wrench. Squeeze the clamp together, and slide it down the hose to release the hose. Detach the heater hose from the engine block. Remove all additional electrical connectors and hoses needed to access the cylinder heads in your F250.
5Remove the mounting bolts for the cylinder heads with a socket wrench, and lift the cylinder heads from the engine block. Remove and discard the cylinder head gasket from the engine block. Clean all traces of the gasket from the engine block with a gasket scraper.
How to Replace an Oxygen Sensor in a Wrangler
If the check engine light on the dash of your Jeep is on, stop into an auto parts store and ask them to scan your Jeep for codes. Nearly all major auto parts store offer this service for free. Failure of the oxygen sensor is a common problem, but the part can be changed at home, saving you a major repair bill. The oxygen sensors are in the exhaust pipe between the engine and the catalytic converter on the Jeep Wrangler. You will need a special socket to remove the oxygen sensor, available at most auto parts stores and tool supply stores.
Instructions
- 1
Lift the Jeep with a jack and support it on all four corners with a set of jack stands. The oxygen or O2 sensors are in the exhaust under the middle of the Jeep, so you will have to lift the entire Jeep to access them effectively.
2Locate the two O2 sensors in the exhaust system. The first one is near the center of the transmission, and the second is between the resonator and the catalytic converter. Unplug the wiring harness connectors from both sensors by lifting the locking tab with a small flat screwdriver and pulling them from the harness.
3Remove the O2 sensors, one at a time, using a oxygen sensor socket and a ratchet. Turn the sensor counter-clockwise to remove it from the exhaust. Discard the old sensor.
4Install the two new sensors into the threaded sections of the exhaust where you removed the old ones from. The two sensors used by Jeep are identical, so either one is fine in each hole.
5Tighten the sensors with an oxygen sensor socket and a torque wrench to 22 foot-pounds. Do not use thread locker, anti-seize or any other compound on the threads of the sensor.
6Insert the wiring harness connectors on both sensors into the plugs on the wiring harness. Verify that they lock into the connector by checking the tab to see that it is engaged.
7Remove the jack stands and lower the Jeep to the ground. Test run the engine and check your CEL or check engine light to ensure it has gone off.
Thursday, April 10, 2014
How to Replace an Exhaust Flange Gasket
All vehicles have at least one pipe with a flange connection. The front pipe or header pipe bolted to the manifold uses a flange of some type. Many modern vehicles now connect other components, such as catalytic converters, downstream exhaust pipes and even mufflers, with flange connections. With the car on a lift and a mechanic that knows what he is doing, the repair could take a mere few minutes. With a home repair mechanic laying on his back with limited tools, the repair could become complicated.
Instructions
- 1
Inspect the pipe with the leaking flange gasket caully before attempting to disconnect it. Front-pipe-to-manifold flanges often require the rear flange to the converter or pipe be separated in order to access the leaking gasket. Sometimes unhooking an exhaust hanger somewhere down the exhaust stream might allow enough flexibility to forgo the rear flange disconnection.
2Determine how the flange is connected. All front-pipe-to-manifold flanges are secured by nuts to the studs of the manifold. Downstream flange connections may use studs on one side and nuts on the other or simple nuts and bolts. Downstream studs can be distinguished by round heads which, unlike a hex bolt head, cannot be held with a wrench. Studs have grooved notches in their shafts and do not require a box-end wrench for removing the nut. Nut and bolt connections will require the bolt of the head be held stationary (with the wrench) while a ratchet and socket loosen the nut (or another wrench).
3Disconnect the flange hardware. If necessary, heat the nuts of the connection with an oxyacetylene torch. Using a portable propane torch may not heat the nut up enough or could take a considerable amount of time. Heat just the edges of the nut and not the bolt. This will expand the nut. Once the nut is cherry red, turn off the torch and remove the nut. For front pipes, a ratchet, long extension and socket are most likely required.
4Repeat for each nut and stud/bolt connection of the flange until all retaining hardware is removed. The studs will remain intact on their respective exhaust components.
5Separate the flange connection. This is where the exhaust pipe hanger tool may come in handy. Releasing one or more exhaust hangers near the flange connection may give the exhaust system enough flexibility to access the mating surfaces of each mating flange. As mentioned earlier, it may also require separating the other connection of the exhaust component with the compromised flange gasket.
6Clean each flange connections mating surface with emery cloth or medium-grit sandpaper, after allowing the exhaust system to cool down, if a torch was used.
7Apply a level amount of high-temp Perma-Tex (O2 sensor-safe) compound on both sides of the gasket. Place the gasket between the flanges. On most flange connections, theres a small piece of pipe protruding on the inside of the flange to place the gasket on, depending on the type of application. Some front pipe gaskets are called "donut" gaskets and fit into a ball-flared exhaust pipe.
8Reconnect the flange connection, after replacing the system on hangers, if applicable, with new hardware (nuts, bolts, washers and lock washers).
9Start the vehicle and check the flange connection for leaks. If necessary, re-tighten the hardware.
Sunday, April 6, 2014
What Does an Intake Gasket Do
Intake gaskets seal gaps between the intake manifold and the cylinder head. They are made in thicknesses ranging from 0.060 inch to 0.120 inch. If too much air gets into the system, the car will not run properly.
Intake Manifold
Gaskets are located throughout the engine, but one of the most important parts of the engine is the intake manifold. The intake manifold regulates the amount of air and fuel your engine gets to create the combustible reactions that power the business. The gaskets can withstand temperatures of 500 degrees Fahrenheit and higher. Some gaskets are made from high-temperature plastic that actually cools the air that passes through them.
Gasket Problem Symptoms
You know that your intake gaskets are no longer doing their job if you start seeing puddles forming under the car when it is in park or when you see a leak in the coolant system. Also, if your engine is rough and slightly jerky, or if you hear whistling from the engine taking in excess air, you have problems with your gaskets.
Repair
A vacuum gauge that checks manifold pressure is used to find the leak. All coolant must be drained from the vehicle and the manifold must be removed in order to replace the gaskets.
Warning
In the book, "Small Black Chevy Engine Buildups," the editors write that with too much air "your engine will turn into melted cheesecake; too little and itll drive like melted cheesecake."
Saturday, April 5, 2014
How to Install an EX500 Carb
The EX500 carburetor is used to bring the right mix of air and fuel into a car engine. When a carb isnt working, the engine will either die or it will take in too much fuel. The EX500 will make the engine run again, but it will also cut down on fuel intake. You dont have to be a mechanic to install the carburetor; you can do it yourself.
Instructions
- 1
Pop the hood on your car and locate where the carburetor should be installed next to the engine. Clean the intake manifold on the top of the carburetors gasket surface with a rag. Remove the old carburetors gasket with a razor blade.
2Put the EX500s gasket over the four studs where the carburetor will be installed. Place the EX500 over the four studs and then place it over the gasket.
3Connect the four retaining nuts over the studs on the corners of the carburetor. Tighten the nuts with a socket wrench. Apply the gasket glue to the gasket and allow it to dry. This should take about four minutes.
4Put the small hose clamp over the end of the cars fuel line. Connect the fuel line to the fuel inlet on the carburetor. This is on the right side of the carburetor. Slide the larger hose onto the fuel line and then tighten the clamp with a screwdriver.
5Connect the throttle cable to the cars throttle linkage. This is located on the right side of the carb. Connect the distributor vacuum line to the inlet on your carb. Turn on the car.
Thursday, April 3, 2014
The Location of an AC Condenser on a 2001 E320
Air conditioning was one of the great inventions of the 20th century that most of us take for granted. For granted, that is, until we encounter a hot summer day without electricity or with a malfunctioning vehicle AC system. The Mercedes Benz 2003 E320 air conditioning system, like all vehicle air conditioning systems, has three main components---a compressor, a condenser and an evaporator. Its a quick task to locate the condenser.
Instructions
- 1
Locate the hood release under the dash close to the drivers side door. It is a small level that in located above the emergency brake pedal and below the emergency brake release lever. You may have to feel under the dash for the hood release lever.
2Pull the hood release lever towards you. You will hear a noise and observe the hood rise slightly when the hood unlocks.
3Proceed to the front of the vehicle and lift the hood slightly. A grey or black tab will protrude out through the grill. Pull on the tab and open the hood by lifting it.
4Look down to area at the front of the vehicle behind the location of the grill prior to opening the hood. You are now looking at the radiator and the condenser. The condenser is in front of the radiator.
Wednesday, April 2, 2014
How Much Should I Pay for an Engine Rebuild
Defining Rebuild
Having your engine rebuilt will cost between $1,100 and $3,000, depending on the size and type of engine. A rebuild restores every part to original manufacturers specifications, and may include parts of your current engine. This is different from an overhaul in that an overhaul only fixes things that are worn out. A rebuild essentially starts over and includes used parts.
Other Options
The engine is the most expensive piece of your automobile, so whatever you do, you will be spending a lot. "Crate" engines also are available, which are brand new engines. The cost usually is a little more, but you are getting all new parts and usually a longer warranty. The ultimate option of course, is to trade in your car for a new or different car.
Bottom Line
A lot depends on how attached you are to your automobile, and its overall condition. If there are other major issues, such as transmission or suspension problems, or body damage, you might be better off getting a new or different car.
Saturday, March 29, 2014
The Parts of an Engine Lift
An engine lift, also called a hoist, is a heavy-duty piece of equipment used to lift automobile engines out of the chassis so that mechanics can work on or replace them. Engine lifts are manufactured by numerous companies, but designs are generally the same with similar parts. A typical engine hoist is composed of a stand, a jack, (also called a hydraulic ram) and a boom with chains and hook attachments.
The Stand
The engine lift stand, also called the legs or frame, is a foundation that stabilizes the lift and bears the weight of the engine when the lift is loaded. A good engine lift stand is made of steel or other sturdy, durable metal. Many engine lift stands are equipped with pivoting casters with locking brakes so that the entire lift can be easily and safely moved or repositioned.
The Jack or Hydraulic Ram
The jack or hydraulic ram composes the vertical, central portion of an engine hoist, and is the part of the device that does the actual lifting. The hydraulic jack functions similarly to a car jack, and is equipped with a lever operated by manually pumping it to raise the engine incrementally. All hydraulic rams should be equipped with a safety device to control how quickly the lift lowers the engine, and to prevent it from slipping or dropping.
The Boom, Chains and Hooks
The boom is a long, horizontal arm, usually equipped with chains and hooks, that is mounted onto the hydraulic jack. A boom is designed to balance load forces so that a loaded engine lift will not tip over. Once the hooks are attached to the engine, the boom rises incrementally as the hydraulic jack is pumped, lifting the engine free of the chassis. The chains allow the engine to dangle from the boom with some horizontal motion, which makes it easier to maneuver the engine.
Tuesday, March 18, 2014
How to Paint a Car With an Airless Sprayer
Airless sprayers work by pumping out paint from a small tip on a spray gun. There are no air compressors, nor is air involved in any way to move the paint. Airless sprayers are very efficient and will apply paint very quickly over a large area. If you are using an airless sprayer to paint your car, there are a few things to keep in mind.
Instructions
- 1
Cover all areas of your car that are not to be painted. An airless sprayer is not as easy to control as a brush, so do not take any chances that you may accidently spray a mirror or glass. When spraying, the airless sprayer paint will create a cloud of paint that will settle. Wear a protective covering.
2Keep the spray gun aimed at the area that you want to paint. Never point it towards yourself. Move your hand in a horizontal motion while spraying. Do not stop to spray as you will create a heavy concentration of paint in one area.
3Begin moving your hand from side to side. Once you have a steady motion, begin to pull the trigger.
4Release the trigger before stopping motion of your hands when you are ready to quit painting.
5Clean the sprayer so that no paint builds up and dries up inside.