Wednesday, August 27, 2014
Styles of Rod Bearings
Rod bearings or connecting rods connect the pistons to the crankshaft and must be strong to withstand the internal forces from pistons directional changes as well as transmit the piston thrust to the crankshaft. Rod bearings are mainly made of aluminum for smaller engines and forged steel. The upper end of the rod bearing is connected by a piston pin to the piston and the lower end of the rod is split so that it is clamped around the crankshaft in a certain style.
I-Beam
I-beam are the most common styles of rod bearing connection and are used for performance builds and stock applications. These rods are characterized by a large flat area perpendicular to the side beams. The rod side beams are parallel to holes found in the crank journal and piston pins, providing an excellent combination of compressive and tensile strength as well as light weight. I-beam rods handle high rpm tension although they might bend or fail when exposed to high compressive forces. I-beams can be made wider or thicker so that they can handle large horsepower loads.
Oval Beams
Oval beams are also erred to as parabolic or radial beams and are a variation of the basic I-beam. They are created by leaving a rounded region next to the two beams, thus increasing the rigidity and strength. This scalloped effect created by the rounded area is aimed at improving the performance of rod bearings and minimizing bending or failure of rod bearings.
H-Beams
H-beam rods are made of two big flat-sided beams lying at a 90 degree angle to the crankshaft journal bores and the piston pin. Lateral stiffness is provided by the center region linking the two sides of the H jointly. In comparison with the I-beam, this design weighs less and has superior compressive power. H-beam style is recommended for applications with high torques generating huge amounts of power below 6,000 rpm.
Implications
Rod bearings are specifically engineered to meet particular requirements that take into consideration the amount of load produced by the engine. For example, passenger cars are not frequently full-loaded and might require different rod bearings from applications with heavier loads, such as marine or heavy duty trucks. Also take into consideration that putting more load on the bearing makes it difficult to maintain the oil film connecting the bearing and shaft, reducing the longevity of the rod bearings.
Friday, June 6, 2014
The Symptoms of a VW Belt Tensioner Pulley
The Volkswagen (VW) belt tensioner pulley tightens the serpentine belt that turns the engine accessories, such as the air-conditioning compressor and water pump. The newer model VWs have an automatic tensioner pulley that tightens the serpentine belt as it stretches, but the older model VWs have a tensioner pulley that needs to be adjusted. The tensioner pulley shows symptoms when it is going out or requiring replacement.
Serpentine Belt Squealing
The VW belt tensioner pulley can become too tight or too weak, allowing the serpentine belt to wear prematurely or slip under normal operating conditions. The belt begins to squeal when the tensioner pulley is not tight enough, causing the engine to overheat because the water pump is not operating efficiently. This symptom can be caused by the tensioner pulley spring, which weakens over time and does not place enough tension on the belt. The serpentine belt can also begin to run too hot and prematurely fail. The tensioner pulley needs to be replaced when these symptoms occur.
Engine Overheats
The engine in the VW can overheat when there is a problem with the belt tensioner pulley. This symptom is caused by corrosion building up on the tensioner pulley that does not allow the pulley to adjust the serpentine belt. When corrosion builds up, the pulley becomes jammed or does not rotate, causing the serpentine belt to stretch and loosen on the engine accessories. The corrosion does not allowing the pulley to adjust to the stretched belt, creating the water pump problem. This corrosion is generally caused by road debris and dampness splashing onto the tensioner pulley. Proper lubrication of the tensioner pulley periodically can prevent this corrosion build-up.
Dead Battery
Another symptom of a VW belt tensioner pulley going bad is the battery not charging properly. A failing tensioner pulley does not provide enough tension on the serpentine belt, preventing the alternator from recharging the battery. The loose serpentine belt does not allow the alternator to turn fast enough to charge the battery, and the battery can quit working or fail to provide enough charge to the ignition and electrical system to start the engine. The tensioner pulley needs to be replaced or inspected when the serpentine belt is replaced to ensure that the tensioner pulley keeps operating efficiently.
Saturday, May 17, 2014
What Is the Benefit of a Transmission Service
Ask any mechanic and youll be assured that having your transmission serviced on a regular basis is a smart move and will extend its life. Service can range from a basic service check to a pressurized flush. Aside from the fact that a flush replaces the old fluid in your transmission with new fluid, this procedure also cleans the filter and system; in addition, it can identify minor transmission issues before they become major problems.
General Benefits
A general transmission service involves removing the fluid pan, replacing the filter and gasket, and replacing some of the transmission fluid. According to Speed Lube, this routine service extends the life of the transmission. Clean lubricant prevents seals and gaskets from hardening, which can cause metal parts to warp and valves to stick.
Full Transmission Flush Benefits
A flush replaces all of the vehicles transmission fluid. Pressure is used to push all of the old fluid out so that it can be replaced with new fluid. Flushing also does a good job of cleaning out a transmissions internal parts and its filter.
Discovering Transmission Issues
Both general service and a flush can reveal transmission problems but a flush will give a more accurate indication of what is going on inside your transmission. This is because the pressurized cleaning method helps expose decaying seals and cracks. It will be less costly to replace an old seal or gasket than to wait for serious damage to occur and then have to replace the complete transmission.
Wednesday, May 14, 2014
Specifications of an NV3500 Transmission
The NV3500 is a five-speed manual transmission found in General Motors and Chrysler trucks.
The manufacturer, New Venture Gear, is a company that was formed through the merger of the manual transmission engineering and manufacturing divisions of GM and Chrysler.
Design
The NV3500 is a fully synchronized, constant mesh transmission. The clutch housing, or bell housing, is an integral component to the transmission and is not meant to be removed. According to DodgeRam.org, the NV3500 "has a single shaft shift mechanism with all three shift forks mounted on the shaft."
Variations
The HM290 model, found in GM trucks beginning in 1988, was the forerunner of the NV3500-series transmission. This unit, and the 560 which superseded it, have four shift rails. When this transmission was re-engineered as the NV3500, a single shift rail was used in the design.
There are many design variations of the NV3500, each with unique parts. Two-wheel drive and four-wheel drive variants are available. Another variant is the NV3500HD.
Model Lines
The NV3500 transmission was deployed in the full-size half-ton Chevrolet Silverado and GMC Sierra pickups, Chevrolet S10 and GMC S15 trucks beginning in 1990, and some Dodge Dakota trucks beginning in the 1994 model year.
In the Dakota, the NV3500 is used with V-8 engines including the 3.9-liter and 5.2-liter Dodge powerplants.
Hauling Capacity
According to DodgeRam.org, the NV3500 is rated to a maximum GVWR of 7,200 lbs. and a maximum GCVWR of 11,000 lbs. The NV4500 transmission, built for larger engines, is a heavy-duty transmission for trucks that require greater hauling and towing capabilities.
Sunday, April 27, 2014
Types of Carburetor Chokes
Over the years, various models of carburetor chokes have been developed in order to facilitate different engine conventionalities such as differing engine designs, varying load requirements and air/fuel intake varieties. In essence, the varieties of carburetors have been specifically designed to provide an assortment of drafting amounts, a multitude of barrels and varying venturi and flow rates.
Carburetor Draft
The variation in draft technology is one way in which carburetor chokes can be classified. Drafting within carburetors can be defined as sucking in or exhaling out air. There are three main types of drafting technologies that can be incorporated into carburetors. These are downdraft, sidedraft and updraft models. The downdraft and updraft technologies work using a method completely opposite to each other. Downdraft allows air to flow through the engine in a downward direction whereas the updraft variety allows air to be transferred through the engine in an upward direction. On the other hand, the sidedraft variety allows air to flow through the engine in a horizontal manner. Sidedraft technology was incorporated into older vehicle models whereas downdraft technology is used in cars these days. However, updraft carburetors are used in machinery such as forklifts.
Carburetor Barrels
Carburetor barrels can basically be defined as a hollow cylinder in which air and fuel is mixed by the engine. The basic parts are the throttle plate, air horn and venturi. There are three essential types of carburetor barrel models; one-barrel, two-barrel and four-barrel carburetors. The one barrel model is primarily incorporated into small engines that do not require a lot of power such as a motorcycle. On the other hand, a two-barrel system is used in cars with large engines and comprises two throttle plates and double venturis. A four-barrel model is used with trucks and SUVs because it has the ability to provide a large amount of engine force. Under normal conditions, the engine uses only two of the four barrels. If extra power is required, the other two barrels are employed to mix in more fuel and air.
Feedback Carburetor System
In accordance with technological breakthrough of todays day and age, car makers have developed an electronic carburetor system that has the ability to provide highly efficient energy by electronically maintaining the levels of air and fuel. The electronic carburetor is used in almost all of the cars being built today and also has the ability to reduce pollution by oxidizing HC and CO as well as reducing the amount of nitrogen oxide expelled into the air. The entire system uses a three-way catalytic converter which maintains the most efficient mixture of air (oxygen) and fuel.
Sunday, April 6, 2014
The Location of the Oil Pan Sensor in a 1990 Mazda MPV
The oil pan or oil level sensor in your Mazda MPV monitors the amount of oil in the oil pan. The sensor has an electrical connection that enables it to communicate with the PCM (power control module). When the oil level reaches or falls beneath the sensor, it illuminates the oil light in your MPVs dash cluster. Damage to the oil level sensor most often results from electrical failure. You can located and replace the oil pan sensor on your 1990 Mazda MPV right at home. The job should take you approximately 30 minutes.
Instructions
- 1
Place a wheel block firmly into position behind both of your MPVs rear tires.
2Apply the emergency brake and raise the front end of your vehicle with a hydraulic jack. The bottom of both of the front tires should visibly measure no more than 8 inches from the ground.
3Set a jack stand behind the front tires underneath your MPVs frame rail. Lift the support arms on both jack stands to 85 percent of the height of the hydraulic jack.
4Lower the hydraulic jack slowly while you monitor both of the jack stands. When you see that your MPV securely rests on the support arms of the jack stands, stop lowering the hydraulic jack. Do not completely remove or lower the hydraulic jack. Leave it in its position for extra support.
5Slide under your Mazda MPV and locate its oil pan. The oil pan sits at the lower, rear of the engine. It looks like a black, metal rectangle and has 20 small bolts around its upper lip. The oil pan also has a large bolt at the bottom of it used to drain the oil.
6Locate the oil pan sensor on the lower side of your oil pan. You will not be able to see the sensors length but you should see the wiring harness connected to the top of it. On some models of the 1990 Mazda MPV, the sensor mounts just above the oil draining bolt. On other models, the sensor mounts on the opposite side of the oil pan across from the oil draining bolt.
Thursday, April 3, 2014
The Location of an AC Condenser on a 2001 E320
Air conditioning was one of the great inventions of the 20th century that most of us take for granted. For granted, that is, until we encounter a hot summer day without electricity or with a malfunctioning vehicle AC system. The Mercedes Benz 2003 E320 air conditioning system, like all vehicle air conditioning systems, has three main components---a compressor, a condenser and an evaporator. Its a quick task to locate the condenser.
Instructions
- 1
Locate the hood release under the dash close to the drivers side door. It is a small level that in located above the emergency brake pedal and below the emergency brake release lever. You may have to feel under the dash for the hood release lever.
2Pull the hood release lever towards you. You will hear a noise and observe the hood rise slightly when the hood unlocks.
3Proceed to the front of the vehicle and lift the hood slightly. A grey or black tab will protrude out through the grill. Pull on the tab and open the hood by lifting it.
4Look down to area at the front of the vehicle behind the location of the grill prior to opening the hood. You are now looking at the radiator and the condenser. The condenser is in front of the radiator.
Saturday, March 29, 2014
The Parts of an Engine Lift
An engine lift, also called a hoist, is a heavy-duty piece of equipment used to lift automobile engines out of the chassis so that mechanics can work on or replace them. Engine lifts are manufactured by numerous companies, but designs are generally the same with similar parts. A typical engine hoist is composed of a stand, a jack, (also called a hydraulic ram) and a boom with chains and hook attachments.
The Stand
The engine lift stand, also called the legs or frame, is a foundation that stabilizes the lift and bears the weight of the engine when the lift is loaded. A good engine lift stand is made of steel or other sturdy, durable metal. Many engine lift stands are equipped with pivoting casters with locking brakes so that the entire lift can be easily and safely moved or repositioned.
The Jack or Hydraulic Ram
The jack or hydraulic ram composes the vertical, central portion of an engine hoist, and is the part of the device that does the actual lifting. The hydraulic jack functions similarly to a car jack, and is equipped with a lever operated by manually pumping it to raise the engine incrementally. All hydraulic rams should be equipped with a safety device to control how quickly the lift lowers the engine, and to prevent it from slipping or dropping.
The Boom, Chains and Hooks
The boom is a long, horizontal arm, usually equipped with chains and hooks, that is mounted onto the hydraulic jack. A boom is designed to balance load forces so that a loaded engine lift will not tip over. Once the hooks are attached to the engine, the boom rises incrementally as the hydraulic jack is pumped, lifting the engine free of the chassis. The chains allow the engine to dangle from the boom with some horizontal motion, which makes it easier to maneuver the engine.
Monday, March 24, 2014
What are the Types of Steel Drive Shafts
Drive shafts, also called propeller shafts, are a very important part of a vehicles engine system. They are essentially hollow tubes which connect the transmission output shaft to the differential pinion shaft. The vast majority of drive shafts are made from steel, including those for racing vehicles, motor homes, trucks, four-by-four vehicles and replacement parts. Different kinds of steel are used on various types of drive shafts.
OEM Steel Drive Shafts
OEM steel drive shafts are rated for less heavy-duty service than other types of steel drive shafts. Usually they can handle about 350 pounds per foot, or about 350 to 400 horsepower. This is the lowest performance level for steel drive shafts.
Dsaya Steel Drive Shafts
Dsaya steel drive shafts, stronger than OEM drive shafts, usually can handle about 1,300 pounds per square foot of pressure, which is comparable to about 1,000 to 1,300 horsepower. If your car does not require a lightweight unit, a Dsaya steel drive shaft is an excellent choice.
Chrome-Moly Steel Drive Shafts
Chrome-moly steel drive shafts are the strongest possible type of steel drive shaft. You will find this type of steel drive shaft in Pro Stock-style racing cars. Chrome-moly steel can be strengthened even further if it is heat-treated. Heat treatment will raise the torsional strength about 22 percent and raise the drive trains critical, or maximum, speed by about 19 percent.
CV Steel Drive Shafts
Constant-velocity (CV) steel drive shafts are so named because they revolve at the same speed during the entirety of their operation. One of the most common types of drive shaft, they come in several different subtypes, mostly characterized by the way in which the transmission output shaft and the differential pinion shaft connect.
Split Drive Steel Drive Shafts
Split drive steel drive shafts are two-piece drive shafts used on many vehicles with longer wheelbases. They are characterized by an extra U-joint and a center bearing which provides greater support to the shaft assemblys middle area.
Torque Tube Steel Drive Shafts
Torque tube steel drive shafts are used on cars with independent rear suspensions. This type of drive shaft is connected rigidly at both ends, with a rotating inner shaft.
Flexible Steel Drive Shafts
Flexible steel drive shafts are very rare and quite different than other steel drive shafts. They are not rigid shafts but are instead just large steel cables.
Sunday, March 16, 2014
The Effects of a Front Spoiler on Gas Mileage
Fluid dynamics is a complex subject; every time you think you understand one aspect of it, it seems as though youve missed some tiny, all-too-pertinent detail that will make or break the entire construct. Such is the case with spoilers, splitters, wings, ramps, canards and air dams. While the layman might use these terms interchangeably, the fact is that they all act in different ways in terms of their effects on a cars high-speed stability, handling balance and fuel economy.
What Spoiler?
Technically speaking, theres no such thing as a front spoiler; and to the extent that there is, its called an "air dam." By definition, a spoiler "spoils" existing airflow patterns on a cars body to smooth airflow and reduce drag. Theyre not intended to block airflow, create downforce (the opposite of lift) or establish new airflow patterns, all of which a front "spoiler" does. While it may seem a bit semantic, this concept is key to understanding how different types of front aerodynamics -- often collectively and incorrectly erred to as spoilers -- affect performance and fuel economy.
Air Dams
The simplest and most common type of front spoiler is called an air dam, and it does just what it sounds like it does. An air dam is just a piece of bodywork that extends downward from the front bumper and reduces the amount of air flowing under the car. This does two things; first, it keeps high-speed air from "catching" on protuberances under the car and creating drag, and it reduces lift by decreasing the amount of potential energy going under the car. An air dam would ideally scrape the ground as you drive, and will generally improve the cars fuel efficiency and high speed stability.
Splitters
Though often used in conjunction with an air dam, a splitter is an entirely different animal. A splitter is a thin, flat, horizontal "shelf" extending frontward from the bottom of the air dam. Normally, air encountering the bottom of the air dam would have to pressurize and become turbulent before it splits and goes either under the car, over the hood or around the sides. A splitter acts like a knife, cleanly cleaving the airflow in two so that it remains laminar, or straight and turbulence-free. A splitter -- often erred to as the "front wing" -- creates a powerful pocket of pressurized air in front of the bumper, which shoves the front of the car down and creates downforce.
Downforce and Fuel Economy
Downforce and lift will always hurt a cars fuel economy because they force the car to expend energy doing something it doesnt need to do -- namely, to either compress the springs or try to fly. The longer a front splitter is, the larger the air pocket it can contain and the more downforce it will produce; good for grip at high speeds, but bad for fuel economy. Additionally, any angled surface on the front bumper that directs airflow upward -- an angled splitter, a ramp or the wing-like canard -- will generally hurt fuel economy by increasing frontal pressure and downforce.
Exceptions
There are a few exceptions to the "air dam helps economy, downforce hurts it" rule. Canards are one of them. A small canard strategically mounted on the corner of an air dam helps to control airflow over the sides of the car, which keeps it out of the wheel-wells and impacts where it will end up behind the car. This can reduce the cars total drag, which may offset the frontal pressure increase caused by the canard. A splitter extending well under the car will act as a partial "belly pan," increasing air velocity under the engine and reducing total drag.
Sunday, March 9, 2014
How Do I Get a Broken Contact Point Out of an Indicator
The indicators on a car or motorcycle need to be functional in order for the vehicle to be road-worthy. Making turns or changing lanes without informing other road users can be very dangerous. If one of your indicators has a burned or broken contact, it will be necessary to repair it. Removing the contact and replacing it with a new one is a far more cost effective solution than replacing the whole indicator.
Instructions
- 1
Turn off the ignition and remove the contact clips from the battery. Use the screwdriver to remove any mounting screws holding the indicator assembly to the body. It should lift out as one complete unit.
2The indicator assembly consists of a front and rear half, which are usually held together by means of a sprung plastic clip bridging the two halves. Locate the clip and press it using the blade of the screwdriver. The two halves will separate, revealing the inside of the indicator.
3Unscrew the bulb and lift it out of the assembly. With the back of the assembly removed, you should be able to see the wiring. Locate the burned or broken contact.
4Heat up the soldering iron and hold it to the base of the contact. The metal tab of the contact is held in place by a plastic spade clip, but the soldered electrical connection at the base must be released to remove it from the plastic clip. Melt the solder, taking care not to touch the plastic ridges at the edge.
5Grip the end of the contact with the needle-nose pliers and pull it toward you, it should slide out from the clip, allowing you to replace it with a fresh one.
Monday, March 3, 2014
The History of Automotive Air Conditioning Systems
The typical automotive air-conditioning system uses a compressor, receiver drier, condenser, rigerant, evaporator and thermostatic valve. This was not so in the early days of automotive air conditioning for cars and trucks, which were primitive by todays standards. The history of air conditioning started with a patent submitted by Willis Carrier in 1906, for building structures. The invention caught on with car and truck applications during the early middle half of the 20th century.
Automotive Air Conditioning Debut
A New York company was the first source of air conditioners used on cars in 1933. The units were highly customized and individually fitted on expensive, privately owned cars and limousines.
Freon Beginnings
The compound chemical Freon, invented by Charles Kettering and Thomas Midgley, was composed of chlorofluorocarbons -- a mixture of carbon, fluorine and halogens of hydrogen and chlorine. Although the invention and application of Freon was first used in air-conditioned buildings, it would later be applied to automotive air-conditioning systems that used coils, condensers and compressors to circulate a rigerant.
Packard Motors
The Packard Motor Car Company offered the first workable air conditioner and heater combination for cars in 1939. The unit cost $274, considered an expensive option at the time. The compressor, a 1.5-ton unit, ran off a belt from the engine. The unit had no thermostat control for turning it down or shutting it off, as it required removal of the belt from the engine. The cool air was gathered at the rear of the vehicle and discharged forward.
Cadillac
Cadillac followed suit in 1941, manufacturing its own air-conditioning system, similar to the Packard design. Cadillac sold over 400 cars that had the expensive option. The bulky unit was located behind the rear passenger seat; it also had to be deactivated by removing the compressor belt.
Frederick McKinley Jones
Frederick Jones was a mechanic and inventor who applied for and received more than 40 rigeration patents for air conditioning. In July 1940, he was issued a patent for a cooling device that mounted to the roof of a truck. Not long after, the invention was produced for rigerated trucks that transported flash-frozen foods, which was an invention of Clarence Birdseye.
Nash
The Nash-Kelvinator Corporation was the first manufacturer of a integrated ventilating, heating and air-conditioning system. The unit was mass produced and used on the Nash Ambassador in 1954. It boasted a compact style, affordable price at $345, adjustable dash controls, electric clutch, dash-mounted vents and was located entirely in the engine bay. The mass produced units were called the "All-Weather Eye."
General Motors
General Motors manufactured a front engine-mounted air conditioning system in 1954. It came as an option on its Pontiac cars, which had straight eight-cylinder engines. Separate controls were added for air distribution and cooling levels. The design differed slightly from the Nash layout and concept.
The 1960s
Air conditioning for cars and trucks picked up in popularity and application by 1960, outfitting about 20 percent of U.S. vehicles. The Southwest used systems in 80 percent of its vehicles. American Motors introduced air conditioning on all AMC Ambassador models starting in 1968. At the turn of 1969, 54 percent of all domestic vehicles had air-conditioning systems. Automatic climate control thermostats were first introduced and applied during this time.
.
Introduction of R-134a
R-134a rigerant was introduced in 1992 as a replacement for the original R-12 Freon. The old R-12 Freon, invented by Kettering and Midgley, was found to contain ozone-destroying chlorofluorocarbons. The new R-134a had no toxic or ozone depleting chemicals, and followed the criteria set forth by the Environmental Protection Agency. All new vehicles manufactured after 1995 were fitted with new air-conditioning systems that used only R-134a rigerant. R-12 was discontinued, with some countries outlawing its use. As of 2011, 99 percent of all vehicles manufactured and on the road have air-conditioning systems, with climate control programming, directional vents and increased performance, allowing for better fuel economy.
Tuesday, February 25, 2014
Purpose of O2 Sensors in Cars
Oxygen sensors, commonly called O2 sensors, are a vital component in maximizing fuel efficiency in vehicles.
Name
An oxygen molecule consists of two atoms of oxygen bound together. Thus, O2 ers to the chemical formula for pure oxygen.
Task
O2 sensors monitor how much unburned oxygen is present in the exhaust from an automobile engine. The amount of oxygen indicates how efficiently the engine is burning fuel.
Effect
The cars computer uses readings from the oxygen sensor to adjust the mixture of air and fuel in the engines combustion chambers for maximum efficiency.
Location
There is an O2 sensor inside the exhaust manifold. Vehicles produced after 1995 also have a "downstream" sensor to measure the exhaust as it leaves the catalytic converter, to ensure that the converter is working properly, too.
Malfunction
Symptoms of a malfunctioning O2 sensor include declining gas mileage, rough idling and engine surges or hesitation. A vehicles "check engine" light will often come one.
Saturday, February 22, 2014
Removal of a 1989 Jeep Gas Tank
Removing the fuel tank from your 1989 Jeep for replacement of the tank, sender or other parts takes a few minutes and a little pre-planning. The tank should be as close to empty as possible to make removal safer and easier. The tank does not have a drain plug, so you will need to siphon the fuel from the tank into an approved storage container before you start or drive it until it is nearly empty. Replacement tanks, sending units and related parts are available at most major auto-parts stores.
Instructions
- 1
Remove the filler cap from the Jeep and set it aside. Position a jack under the Jeep and raise the rear off the ground, then place a set of jack stands under the rear axle to support the vehicle. Remove the jack for now.
2Disconnect the fuel filler hose and vent line from the drivers side of the tank, using a flat screwdriver to loosen the hose clamps. Pull the hoses off the tank fitting and let them hang to one side.
3Position a jack under the skid plate on the fuel tank, then remove the nuts around the edges of the skid plate, using a socket and ratchet. Lower the jack slowly, allowing the fuel tank and skid to drop down from the Jeep until you can reach the hoses and wiring harness connections on top of the tank.
4Disconnect the wiring harness connector from the fuel sending unit and set it aside. Remove the clamps from the hoses on top of the fuel tank with a flat screwdriver, then disconnect the hoses and set them aside.
5Lower the jack, dropping the fuel tank and skid plate out of the Jeep as a complete unit. Slide the tank out from under the truck so you can access any part of it required for the repair you are performing.
Thursday, February 20, 2014
Parts of Power Steering
Power steering ers to steering assisted by a hydraulic pump, a pulley belt controlled by engine speed, a rotary valve device and steering gears. There are two types of power steering: rack-and-pinion steering and the recirculating-ball steering.
Steering Wheel
The steering wheel is a wheel controlled by the driver of the vehicle. When the driver turns the steering wheel, the wheels of the vehicle turn. The steering wheel is the user-controlled part of a power-steering system.
Rotary Valve
A rotary valve is a device that senses the forces applied on a steering wheel. It is part of a spool valve assembly. The rotary valve has a torsion bar. Force applied to a torsion bar causes it to twist and rotate the inside of the spool valve. The top of the torsion bar in the rotary valve connects to the steering wheel. Depending on the steering system, the bottom of the torsion bar connects to the worm gear or the pinion, which turns the wheels. When the spool valve turns, a port opens and allows steering fluid to flow to the appropriate lines. The lines connect to the power cylinder.
Rotary Vane Pump and Pulley
A rotary vane pump provides the hydraulic power for the power steering. The cars engine along with a belt and pulley run the pump. Retractable vanes inside a chamber of the pump spin and force hydraulic fluid to the outlet for the rotary valve. The pump runs faster when the engine is running faster. Higher engine speeds create higher pressure on the fluid flowing to the outlet. The pump also has a pressure-relief valve that opens if there is too much fluid pumping, such as with high engine speeds.
Steering Gear: Rack and Pinion
The steering gear turns the wheels. In a rack-and-pinion steering system, the pressurized fluid pushes on the power cylinder mounted on the rack. The resulting changes in pressure from the fluid moves the rack, making steering easier. The rack is a long metal piece with a flat side. On the flat side there are teeth cut into the edges. A steering shaft connects the steering wheel with the rack. A pinion gear on the end of the shaft connects with the teeth of the rack. On each end of the rack is a tie rod, which connects to the spindle of the wheels.
Steering Gear: Recirculating Ball
In a recirculating-ball system, steel balls roll between the steering shaft and the rack piston. With assistance from the hydraulic system, the rack piston moves up or down on a worm gear to turn the wheels.
Return Line
The return line directs the fluid from the power cylinder back to a reservoir on the pump.
Tuesday, February 4, 2014
Does the Length of the Spark Plug Cables Matter
Plug wires arent the most glorious part of any engine, but they are a bit more complicated than most give them credit for being. While wire length may not seem particularly critical, those wires carry an enormous amount of high-voltage power. Pay close attention to your plug wires, or they may end up sending a message that leaves you saying "Can you hear me now?"
Plug Wire Factors
Two things come into play when discussing spark plug wire length: the resistance of the wire in ohms, and the amount of radio frequency interference it produces. The ohm is a measure of a wires efficiency in passing electrical current. Smaller and less-efficient wires rate higher in ohms, meaning that theyll convert more electrical energy into heat in the plug wire instead of passing it to the plug. Resistance in the plug creates a discharge of positive radio waves, which ground out in a cars stereo system and create static through the speakers.
Ohms and Wires
Different grades of wires produce various levels of ohms per foot. An average stock spark plug wire creates about 5,000 ohms of resistance per foot of length; high-performance wires will average between 100 and 400 ohms, and high-grade race wires may go as low as 2 to 10 ohms. If you apply Ohms Law of voltage loss (Voltage Loss = amperes flowing through wire X ohms of resistance) to a typical high-performance ignition system where the coil produces about 20,000 volts and sends about 0.010 amps to the wires, youll find that a stock wire will cause a drop of about 50 volts per foot, a performance wire will drop about 1 to 4 volts per foot and a race wire might drop as little as little as 0.02 volt per foot.
Voltage Output and Plug Length
Since resistance to flow increases by wire length in feet, multiplying the spark plug wires length in feet by its voltage loss per foot will tell you its impact on spark plug power. In the worst-case scenario, assume that a stock 5,000-ohm wire measures a whopping 4 feet long. Thats a 200-volt drop from ignition coil to plug wire -- a seemingly insignificant 1 percent drop. However, that 200-volt energy loss will go into creating heat in the wire, and ohms of resistance go up with heat. The end result is a cascade effect of failure; the current flow and heat gain will eventually reach an equilibrium, but not before producing a noticeable drop in current, damaging the wires conductive core and hindering its RFI-suppressive qualities.
RFI and Solutions
You can get away with using longer plug wires by using a lower-resistance wire, one thats either thicker or higher quality. However, higher current flows also produce more RFI, which means that youll also need to use a high-quality RFI-shielded wire to prevent interference through the radio system. Even if you never listen to anything but MP3s and CDs, remember that RFI interference is an extremely broadband signal. Under certain circumstances, this signal can reach into the frequency ranges commonly used for cell phones and other communications devices, effectively scrambling the signal. So, if your phone seems to constantly drop calls while in the car, you might want to take a look at those old, cheap or mile-long plug wires.
Sunday, February 2, 2014
Tutorial on Replacing the Thermostat of a Toyota Tacoma
The thermostat in your Toyota Tacoma is an essential part of the trucks engine cooling system. The thermostat expands when the coolant in your engine becomes too hot, opening a valve that allows much more coolant to circulate through the system. The increase in coolant flowing through the radiator brings down the overall fluid temperature, and as a result, your trucks engine continues to operate within the optimal engine temperature. When the thermostat is no longer working properly, the engine overheats and the thermostat needs to be replaced.
Instructions
- 1
Remove the lower radiator hose by unscrewing the clamps and pulling off the hose.
2Unscrew the two bolts on top of the thermostat.
3Remove the thermostat and the gasket from the water pump.
4Clean the thermostat housing, removing any dirt and leftover gasket pieces.
5Line up the valve on the new thermostat with the point on the inlet, and place the new thermostat and gasket into the thermostat housing.
6Screw the two bolts you removed earlier back into place.
7Reattach the lower radiator hose and clamp it into place.
8Top off the radiator with fresh coolant.
Tuesday, January 28, 2014
Highlights in the History of Hydraulics
Hydraulic power relies on the capacity of liquid to provide the power necessary to accomplish mechanical tasks. Hydraulic power is used today in a huge variety of machines, ranging from the heavy equipment used for mining and excavation to basically every car on the road. Pressure applied to fluid inside a closed system provides power that can be harnessed in a variety of ways.
Pascal
Understanding of hydraulic power existed well before French mathematician and physicist Blaise Pascals time. Pascal however, crystallized an understanding of hydraulic pressure that would pave the way for future inventions utilizing this force. Pascals Principle states that "pressure exerted on a fluid is distributed equally throughout the fluid." This means that because fluid does not compress, when you put pressure on fluid at one side of a closed system, it exerts that amount of force on the other side of the system.
Fordson Tractor
Hydraulics in the automotive industry started to take shape when a hydraulic system was first adapted for use in agricultural equipment. Automotive pioneer Henry Ford worked with Harry Ferguson to build the Fordson tractor, which was the first to utilize a hydraulic press. This machine used hydraulic power to lower and lift the various implement attachments that could be used with it. It was the smoothest and most efficient manner of moving heavy equipment on the tractor that had been developed to that point.
Brakes
One of the primary uses of hydraulic technology in cars today is in the braking system. The method of using pressurized brake fluid in a master cylinder to apply stopping power to the wheels was fully realized in America for the first time in 1922. The Duesenberg became the first car in the country to have hydraulic braking power for all four wheels. This technology has been adapted and advanced since then, but automotive brakes still rely on it.
Power Steering
Power steering is the other very important use of hydraulics in the automotive world, and the use of power steering makes it possible to maneuver everything from cars to large military equipment with much more ease. Francis W. Davis was the first to create a hydraulic power steering system in the 1920s. Hydraulic power steering systems started appearing more and more on commercial cars in the 1950s and 1960s.
Monday, December 16, 2013
What Are the Benefits of Removing the Catalytic Converters From Cars
Catalytic converters, which are responsible for igniting and burning unburned engine exhaust gases, became standard automotive equipment on all cars beginning with model year 1975. Although catalytic converters help to make engine exhaust gases cleaner, they are not without their minuses. What follows is a brief list of the potential benefits of removing automotive catalytic converters.
Increased Horsepower
Cars that have their catalytic converters removed experience an increase in engine horsepower. Catalytic converters create a significant source of engine back-pressure due to the constrictive effects they have on exiting engine exhaust gases. Removal of catalytic converters from cars allows exhaust gases to exit their engines much faster and at higher levels.
Better Gas Mileage
Since catalytic converter removal allows for exhaust gases to exit a cars engine at increased speeds, engine back-pressure is reduced, which lessens engine strain. This reduction in engine back-pressure and engine strain enables an engine to work more easily, and thus reduces fuel consumption and increases gas mileage.
Lower Engine Operating Temperature
Since removing a catalytic converter lessens the burden on a cars engine by enabling engine exhaust to vacate the engine more easily, a net effect is a reduction in engine operating temperature. The more easily an engine functions and the less work it has to do results in less friction, less load and, ultimately, a lower operating temperature.
More Fuel Options
Cars equipped with catalytic converters run only on unleaded gasoline. Lead-based gasoline, which produces more power and better engine combustion, quickly destroys the inner catalyst materials of catalytic converters. A car with no catalytic converter will be able to run on a variety of lead-based and/or high-performance fuels that would not be possible with a catalytic converter.
Healthier Exhaust Sound
Catalytic converters operate like car mufflers, whose sole purpose is to muffle the sound of exiting engine exhaust gases. Although catalytic converters burn unburned exhaust gases exiting an engine, thus making tail pipe emissions cleaner, they also further muffle a cars exhaust sound and bestow a somewhat timid, tempered exhaust sound. Without a catalytic converter, a cars exhaust sound becomes a little louder, a little deeper and more distinctive.
Tuesday, December 10, 2013
Purpose of a Transmission Modulator
The purpose of a transmission modulator is to decide when a transmission shift should occur. It also informs the transmission of the type of load being placed on it. Pressure is regulated by the transmission modulator as well, allowing the transmission to function smoothly.
Problems
There are several problems that can occur with a transmission modulator, most of which happen naturally over a period of time. The modulators diaphragm is subject to rupturing, and leaks are known to occur as well. These types of problems in a modulator cause driving issues and may even cause the transmission to fail altogether.
Inspect
Often the first thing youll want to inspect is the line leading to the transmission modulator. If transmission fluid is visible once you disconnect the line, this indicates a leaking diaphragm. The modulator can also be checked for leaks directly using a handheld vacuum pump.
Remove
A transmission modulator can be removed from the transmission so it can be replaced. Before pulling the modulator from its housing unit, the retaining bolt and clamp will have to be untightened first. Because the actuating pin could fall when the modulator is being pulled out, special care should be taken to avoid losing it.