Wednesday, August 27, 2014
Styles of Rod Bearings
Rod bearings or connecting rods connect the pistons to the crankshaft and must be strong to withstand the internal forces from pistons directional changes as well as transmit the piston thrust to the crankshaft. Rod bearings are mainly made of aluminum for smaller engines and forged steel. The upper end of the rod bearing is connected by a piston pin to the piston and the lower end of the rod is split so that it is clamped around the crankshaft in a certain style.
I-Beam
I-beam are the most common styles of rod bearing connection and are used for performance builds and stock applications. These rods are characterized by a large flat area perpendicular to the side beams. The rod side beams are parallel to holes found in the crank journal and piston pins, providing an excellent combination of compressive and tensile strength as well as light weight. I-beam rods handle high rpm tension although they might bend or fail when exposed to high compressive forces. I-beams can be made wider or thicker so that they can handle large horsepower loads.
Oval Beams
Oval beams are also erred to as parabolic or radial beams and are a variation of the basic I-beam. They are created by leaving a rounded region next to the two beams, thus increasing the rigidity and strength. This scalloped effect created by the rounded area is aimed at improving the performance of rod bearings and minimizing bending or failure of rod bearings.
H-Beams
H-beam rods are made of two big flat-sided beams lying at a 90 degree angle to the crankshaft journal bores and the piston pin. Lateral stiffness is provided by the center region linking the two sides of the H jointly. In comparison with the I-beam, this design weighs less and has superior compressive power. H-beam style is recommended for applications with high torques generating huge amounts of power below 6,000 rpm.
Implications
Rod bearings are specifically engineered to meet particular requirements that take into consideration the amount of load produced by the engine. For example, passenger cars are not frequently full-loaded and might require different rod bearings from applications with heavier loads, such as marine or heavy duty trucks. Also take into consideration that putting more load on the bearing makes it difficult to maintain the oil film connecting the bearing and shaft, reducing the longevity of the rod bearings.
Sunday, April 27, 2014
How to Thread a Shift Rod
Shift rods are used in cars, trucks and motorcycles that have manual transmissions. A shift rod consists of two eye-bolts that are threaded onto a steel rod. As you change gears, the shift rod engages and disengages the clutch linkage. Shift rods are available in various lengths from auto parts stores, or you can have one cut to a custom length to fit your particular application. A die set may be used to cut threads on a blank or universal shift rod when the original is not available.
Instructions
- 1
Place the shift rod in a bench vise and secure it firmly. If the rod is chrome, place a shop towel around the shift rod before you tighten the vise to keep the rod from being scuffed.
2Measure the internal threads of the eye-bolts with the thread gauge. The gauge will have a mark on its side to show which size thread will need to be cut.
3Select the correct size die and install it in the die wrench. Secure the die by tightening the two screws in the wrench to hold it in place.
4Apply cutting fluid to the area that is being threaded. Place the die wrench on top, perpendicular to the shift rod. Turn the wrench clockwise while pushing down. For every full turn, back the wrench off one-half turn to remove burrs. Continue to turn the wrench until you have cut the thread the desired length.
5Remove metal shavings and excess cutting oil from the shift rod with a shop towel. If cutting both ends of the shift rod, remove it from the vise and turn it over. Repeat Steps 1 through 4.
Monday, March 10, 2014
How to Inspect Tie Rod Ends
Tie rod ends endure a great deal of movement. Movement causes wear, especially if the tie rod does not receive regular maintenance. Lack of lubrication and foreign elements, such as dirt and grit around the ball, can cause tie rod ends to fail prematurely. A ripped or missing dust boot allows dirt and grit to enter the rod end and grind away at the metal. Other problems arise when a vehicle hits a pot hole or is involved in an accident. The shaft of the tie rod becomes misaligned when bent, creating greater tire wear.
Instructions
Raise the Front End
- 1
Block both the rear wheels behind the tires, and apply the emergency brake while parked on a solid, level surface.
2Raise the front of the vehicle by placing a jack under the center of the cross member and jacking it up.
3Insert two jack stands, one under each side of the front frame close to the wheels.
4Place another two blocks, one on the front side of each rear wheel, to prevent the vehicle from moving forward.
Inspect the Tie Rod Ends
- 5
Spray brake cleaner on all the tie rod ends, and wipe clean with a shop rag.
6Inspect the dust boots on all the tie rod ends for cracks or tears.
7Grab each tie rod end component and physically move it to check for stiff joints or excess play.
8Unlock the steering wheel, and have it turned back and forth while visually checking for excess movement in all the tie rods connected to the steering components.
9Inspect all tie rod ends for physical damage, like scrapes, gouges, and bends.
10Grease every tie rod end, and inspect the grease that is pushed out of the boot for dirty grit-filled grease or water.
11Inspect every tie rod end for a cotter pin or lock nut.