Monday, November 17, 2014
Jeep Cherokee Bumper Removal
Removing either the front or rear bumper on the Jeep Cherokee requires basic hand tools and a few minutes time. Even a novice home mechanic can complete the process in the driveway at home or in the garage. The bumpers are not heavy so you can do the job by yourself but a second set of hands is helpful to support the bumper as the last bolts come out. The mounts never changed over the entire production run of the Cherokee, so no matter what year Cherokee you own, the bumpers come off the same way.
Instructions
Front Bumper
- 1
Slide under the front of your Jeep and locate the mounts where the bumper and frame rails meet. There are two side plates, one on the each side of the frame, with three bolts securing them to the frame.
2Loosen the three bolts on both sides of the Jeep with a socket and ratchet. Remove two on each side but leave one in place so the bumper does not fall.
3Remove the last two bolts, while supporting the bumper. Pull the bumper straight off the front off the Jeep. On older models, there may be a vacuum line attached to a ball on the inside of the bumper. Pull the line off when you remove the bumper.
Rear Bumper
- 4
Open the lift gate on the rear of your Jeep Cherokee then slide under the rear bumper of the Jeep. Locate the bumper mounts on the body of the Jeep; there are four bolts on each mounts that thread into the body.
5Remove three of the four bolts from each mount using a socket and ratchet. Leave one bolt on each mount to keep the bumper from falling on you.
6Remove the final bolt on one side with a socket and ratchet while supporting the bumper. Slide to the opposite mount and remove the final bolt there as well.
7Pull the bumper straight off the rear of the Jeep. Set the bumper aside and close the rear lift gate.
Saturday, February 22, 2014
Removal of a 1989 Jeep Gas Tank
Removing the fuel tank from your 1989 Jeep for replacement of the tank, sender or other parts takes a few minutes and a little pre-planning. The tank should be as close to empty as possible to make removal safer and easier. The tank does not have a drain plug, so you will need to siphon the fuel from the tank into an approved storage container before you start or drive it until it is nearly empty. Replacement tanks, sending units and related parts are available at most major auto-parts stores.
Instructions
- 1
Remove the filler cap from the Jeep and set it aside. Position a jack under the Jeep and raise the rear off the ground, then place a set of jack stands under the rear axle to support the vehicle. Remove the jack for now.
2Disconnect the fuel filler hose and vent line from the drivers side of the tank, using a flat screwdriver to loosen the hose clamps. Pull the hoses off the tank fitting and let them hang to one side.
3Position a jack under the skid plate on the fuel tank, then remove the nuts around the edges of the skid plate, using a socket and ratchet. Lower the jack slowly, allowing the fuel tank and skid to drop down from the Jeep until you can reach the hoses and wiring harness connections on top of the tank.
4Disconnect the wiring harness connector from the fuel sending unit and set it aside. Remove the clamps from the hoses on top of the fuel tank with a flat screwdriver, then disconnect the hoses and set them aside.
5Lower the jack, dropping the fuel tank and skid plate out of the Jeep as a complete unit. Slide the tank out from under the truck so you can access any part of it required for the repair you are performing.
Thursday, December 19, 2013
Dent Removal Tools
Paintless dent removal has been practiced by auto professionals for years, and is becoming more widely known outside of the industry, according to MSN Autos. Many dents can even be removed at home with a variety of tools.
Whale Tails
Whale tails are tools that are named for the shape of the tools head. They are very thin and may be slid into tight places, such as between door braces. These tools can get around common features such as a trusion bar, which protects drivers in case of an accident, to pound out dents from inside the car door.
Door Hooks
A door hook is another tool that can easily be slipped into tight spaces to pound out dents. These tools can easily repair dents close to the edge of a sunroof or at the top of the car door. They are made both for right- and left-handed people.
Lights and Reflectors
Optimum visibility is a must when repairing dents in cars. Lights and reflectors may require some teaching in order to use them properly, but after that, they are a tremendous help in lighting an area well enough to see effectively while removing dents.
Wednesday, December 18, 2013
1991 Ford Ranger Head Lamp Assembly Removal
If the composite headlight assembly in your 1991 Ford Ranger needs replacing due to damage or discoloration, the assembly can be removed from the front of the truck with a little effort and basic tools. The assembly uses screws to hold it in place, and while the trim bezel has to come off first, the screws are all readily accessible. If you need to change the bulbs in these assemblies, do it from the rear of the light without removal.
Instructions
- 1
Open the hood of the truck and locate the two screws on the top of the trim bezel. Remove them with a Phillips screwdriver then move to the front of the bezel and locate the four screws in the face of it. Remove them with your Phillips screwdriver and set them aside.
2Pull the trim bezel off the front of the truck and set it aside. There are three clips along the bottom edge of the bezel; they may require you to pull harder than you think you should but they will let go if you pull hard enough.
3Locate the four screws at the corners of the headlight assembly. Remove the screws with a Phillips screwdriver then pull the headlight assembly toward you until you can reach the headlight bulb connection on the rear off the assembly.
4Release the locking tab on the headlight bulb and pull the wiring harness connector off the bulb. Set the harness aside and remove the headlight assembly off the truck.
Monday, December 2, 2013
Vehicle Portable Exhaust Removal
Vehicle exhaust removal is important whenever working on an automobile in an enclosed space. In some garages and work areas, permanent exhaust removal systems may prove too large or inefficient to install. Portable exhaust removal systems are an alternative that allow for larger work areas without sacrificing the safety benefits of proper ventilation.
Why Exhaust Removal is Necessary
Whenever a vehicle engine is running, it is either operating on an electric charge or burning some type of fuel, generally gasoline. According to OnlineLawyerSource.com, the greatest exposure to toxic gasoline fumes occurs when the engine is on during the driving of cars as well as their refueling. Gasoline fumes can cause dizziness, nervous system problems, vomiting and even the loss of consciousness. Additionally, the fumes can increase facility upkeep expenses and can corrode the electronic systems of service equipment. In large garages that may not have an exhaust removal system port for each area, it is important that each running vehicle not connected to the main removal system be hooked up to a portable exhaust removal system.
Portable System Components
Portable exhaust removal systems contain a motorized blower that collects exhaust fumes directly from the vehicles exhaust system. The fumes are sucked in through a 3 1/2- to 4 1/2-inch hose that connects snugly to the vehicle. A fan mounted in an airtight polyethylene case generates the suction and expulsion pressure for moving the vapors.The fumes are then expelled outside through an outlet hose positioned through an open window or door. The removal systems operate on electricity, and they do not circulate fumes through the workspace. Many have mounting brackets for holding the hoses in place, and the main units are generally on wheels for increased portability. Keep in mind that most portable exhaust removal systems are only equipped to handle single-tailpipe vehicles.
Vendors
Airflow Systems, Inc. and JohnDow Industries are two companies that specialize in portable exhaust removal systems. Most of their portable systems are available for around $1,100. The cost is minimal compared to permanent exhaust removal systems for which extensive planning, installation and routine maintenance is necessary. To get a quote for your garage or shop, visit a vendors website and search for a local distributor in your area. Your local specialist will be able to provide you with detailed information about the portable exhaust removal system youre interested in and whether it is equipped to handle your automobile work.
Wednesday, October 30, 2013
Toyota Sienna Oxygen Sensor Removal
Making its debut in 1998, the Toyota Sienna has always featured at least three oxygen sensors, due to the employment of its V-engine. A V-engine is shaped like a V and has an exhaust manifold on each side. Two upstream oxygen sensors monitor the fuel to air ratio before the exhaust hits the catalytic converter. Another sensor is installed in or to the rear of the converter to monitor its efficiency. If the Sienna features two converters, there will be four sensors installed on the minivan. One for each manifold and one for each converter.
Finding the Right Sensor
When an oxygen sensor fails, it will trigger the malfunction indicator light (commonly known as the check engine light) on the instrument panel. Either read the diagnostic trouble code (DTC) with a scan tool or have it read at a local auto parts store. Most all scanners will reveal a DTC(s) with a letter and a number. This specific trouble code number can either be revealed with a brief description by the scanner or may have to be looked up in a on-board diagnostic trouble code list.
Any code that reveals a "sensor 1" problem will indicate it is one of the upstream sensors near the manifold. "Sensor 2" codes will reveal the problem is in the downstream sensor near the converter.
Bank locations are trickier, but not overly complicated. To locate "Bank 1, Sensor 1" simply find where the number one, three and five cylinders are on your Sienna. "Bank 2, Sensor 2" would indicate a problem with the downstream sensor on the number two, four and six cylinder side of the engine.
Replacing the Sensor(s)
While its not a bad idea to replace all the sensors when one fails, sometimes its financially burdening. This is where finding the right sensor comes into play. The front and rear sensors are not the same part numbers and are not interchangeable.
To replace the front sensor(s), lift the front end or the entire vehicle to gain access to the undercarriage of the exhaust system. Locate the sensor and disconnect the wire harness. Use a small screwdriver to depress the locking plug connection if necessary.
Next, use a 22mm wrench or an oxygen sensor socket and suitable ratchet. Sometimes on the front sensors, its difficult to get one tool or another onto them, so use what works best for you. Spray the threads of the sensor with a copious amount of lubricant spray, such as WD-40 or PB Blaster and allow it to soak in for a few minutes. Use the wrench or ratchet to loosen the sensor by turning it counterclockwise. A box-end wrench would work best because an open-end wrench could mar the hex-head shape of the sensor. Simply insert the detached wire through the box-end of the wrench before applying it to the hex-head. The oxygen sensor socket uses a slit down the side of the socket that accommodates the wire. Once the sensor is loose enough, finish removing it by hand.
The rear sensors are easier to access than the actual sensor, but Toyota places the plug connection under the carpet beneath the front seats. This requires opening the door and then removing the bottom door trim panel with a screwdriver. Set aside and reach underneath the carpet and towards the floorboard and then under the seat to obtain the plug. Once disconnected there, return to the undercarriage and simply pull the rubber gasket plug out from the floor board of the Sienna. The gasket holds the wire in place and prevents water from getting into the floor of the cab.
Once the wire is released, remove the oxygen sensor as you would have or already did the front ones.
Universal or Direct-Fit
There are two types of replacement sensors. Many companies try to promote the fact that youll save you money by purchasing universal sensors. These sensors require eliminating the plug connection on both sides of the wire harness. Next, match the wire colors up (which do not always match to the OEM wire harness) and butt connect. Since the rear sensors of the Sienna plug underneath the front seat and carpet, remove the seat to get enough room to perform this.
Compare the prices of the direct-fit sensors before deciding to save money with the universal. You might even find the direct-fit ones cheaper or a couple bucks more.
Saturday, October 5, 2013
Jeep Cherokee Catalytic Converter Removal
Removing the catalytic converter from the exhaust system of your Jeep Cherokee takes just a few minutes and requires minimal tools. Replacement converters are expensive so you may want to consider purchasing an aftermarket unit instead of an original equipment manufacturer (OEM) one as a cost savings measure. Replacement converters are available from your local Jeep dealership or most auto parts stores.
Instructions
- 1
Raise the front of the Jeep Cherokee off the ground with a jack then position a set of jack stands under the front suspension to support it. Slide under the passengers side of the Jeep and locate the converter in the exhaust. The converter sits near the center of the Jeep, between the frame rails.
2Locate the rear mounting flange between the catalytic converter and the muffler. Remove the nuts from the retaining bolts with a wrench then remove the bolts from the flange. Separate the muffler from the converter and push the muffler aside.
3Remove the nuts from the retaining bolts that secure the mounting flange at the front of the converter with a wrench. Remove the bolts from the mounting flange and set them aside.
4Separate the converter from the front exhaust pipe. Lower the converter and slide it out from under the Jeep.
Thursday, October 3, 2013
Alabama Laws Concerning the Removal of Catalytic Converters
The catalytic converter in auto exhaust systems controls air pollution by chemically converting unburned hydrocarbons and combustion products into natural atmospheric gases. Motorists in Alabama may seek to replace these devices with a straight piece of exhaust pipe in the belief removal of the converter increases engine horsepower, or because the converter has failed and they want to avoid the costs of replacing it. But they would be breaking Alabama and federal law.
Systems Must Work
The Alabama Pollution Control Act (State Code Chap. 28, Sec. 22-12) requires owners of automobiles that are equipped with air pollution control systems to maintain those systems in good working order.
Cant Drive Car
The Alabama pollution law prohibits operating a motor vehicle in the state if its catalytic converter and other air pollution control systems have been removed, disabled, or are otherwise not working correctly. Violators face a potential maximum $10,000 fine and up to a year in jail.
Federal Law, Too
Even if Alabama law had stood silent on catalytic converters, there still is a federal law that prohibits removal or replacement of a properly functioning catalytic converter. This law applies in all 50 states, said the U.S. Environmental Protection Agencys website. Violations by individuals are punishable by a fine of up to $2,500, while a business could be fined $25,000. Federal law requires that a failed converter be replaced with one that meets EPA standards and is a match for the original equipment.
Monday, September 30, 2013
Threaded Insert Removal Tool
Threaded inserts are a type of hardware inserted into a hole in a material with no threads, allowing the installation of a threaded item such as a bolt. Removing the insert is necessary if the threads are damaged and no longer allow the insertion of a threaded fastener.
Types
A standard threaded insert removal tool is T-shaped with a shaft length of between 4 and 6 1/8 inches long, a handle that is 3 to 4 inches long and different-size wedge bits for removing different insert sizes. A tap and die set or a standard drill are useful for removing some types of inserts.
Function
Use the T-shaped tool to remove tanged inserts and screwlock inserts. A drill or tap and die work when removing keylocking inserts. A drill is also useful for removing plastic threaded inserts.
Warning
When using a drill, make sure the bit is no larger than the original hole. Using a larger bit will damage the parent material.