Pages

Showing posts with label toyota. Show all posts
Showing posts with label toyota. Show all posts

Friday, June 6, 2014

My 93 Toyota Camry Stalls Wont Start Back Up

My 93 Toyota Camry Stalls & Wont Start Back Up

The 1993 Camry is a sedan manufactured by Toyota. If your Camry is stalling and wont start up, there is probably a problem with your cooling system or the engine coolant temperature sensor. These two problems are not difficult to repair, but could require the help of a service technician. Adding coolant to your system may be the quick fix that you need; however, a broken ECT will need professional service.

Instructions

    1

    Pop the hood to your 93 Camry from the hood latch on the side of the cars grill. Locate the cooling system, which is on the left side of the engine.

    2

    Look at the fill line on the cooling systems tank. Fill the cooling tank with 50/50 coolant; make sure you reach the fill line on the side of the tank. You should always use 50/50 coolant when possible, but you can temporarily use water if you run out.

    3

    Try to start the car. If the car will not start, use a voltmeter to test the ECT. The ECT is on the left side, at the back of the engine. It is a small, green box with two wires coming off it.

    4

    Connect the testing leads to the (+) and (-) terminals and then try to start the car. Watch the reading on the voltmeter. If the reading starts to go up and down erratically, you need to have a service technician replace the ECT.

ReadMore

Thursday, May 8, 2014

How to Remove a Toyota Camry Taillight

How to Remove a Toyota Camry Taillight

The taillight assembly on the Toyota Camry is a single assembly unit. The bulbs are accessible from the trunk, and the taillight assembly is removable for replacement or cleaning. If your taillight is cracked or broken, you should replace it as soon as possible. If water leaks into the taillight assembly, it can short out the bulbs and cause damage to the cars electrical system. You can buy a replacement taillight assembly from an auto parts retailer.

Instructions

    1

    Open the Camrys trunk. Pull the plastic cover off the back of the taillight assembly.

    2

    Remove the three nuts securing the taillight assembly with a wrench.

    3

    Slide the taillight assembly forward away from the rear of the car. Grasp each bulb and twist it slightly counterclockwise then pull back to remove it.

    4

    Remove the taillight assembly from the car once the bulbs are disconnected.

ReadMore

Thursday, March 13, 2014

How to Reset the Power Door Battery on a Toyota Sienna

If the power doors on your Toyota Sienna stick or stop responding, you may need to recalibrate the doors by resetting the power door system. You can reset the power door system at home to save the time spent at a dealership service center. Resetting the system will reprogram the battery and computer chip so that the doors respond to the door controls.

Instructions

    1

    Press the sliding door control button on the Siennas dashboard so that the red line on the button is illuminated. Close the sliding doors.

    2

    Raise the hood of the van, and disconnect the negative ("-") battery cable with a wrench. Wait 3 to 5 minutes, then reconnect the cable.

    3

    Press the "Open" button on the remote key fob to open the sliding doors. Close the door. Wait 10 seconds, then open the door with the remote again.

    4

    Close the door, and wait 10 seconds. Open the door with the remote a third time. Once the third cycle completes, the power door battery is reset.

ReadMore

Tuesday, March 11, 2014

How to Replace a Toyota Rav 4 Catalytic Converter

Toyota Rav4s have two catalytic converters. The front one is bolted directly to the manifold in the front of the exhaust system and the second one bolts directly to that. In most cases, the converter that fails will be the rear converter. Converters fail after a while clogging, breaking down internally (which is a result of clogging and overheating), and have inlet or outlet pipes that crack or leak exhaust. Having to replace them requires experience.

Instructions

How to Replace a Toyota Rav 4 Front Catalytic Converter

    1

    Put the Toyota Rav4 on a car lift and bring all the way up. Put all the listed tools into the tool cart and wheel it near you where its out of the way but where you can access the tools easily. To remove the five nuts going to the manifold, set up the ratchet with a long extension, the swivel, and a socket. In some cases if the nuts are deteriorated, you may need to switch the socket for a nut extractor.

    2

    Put on the safety glasses and light the torch with the striker. Heat up the nuts with the torch, being caul not to heat the studs up as well. Its a tight area and youll have to know how to handle a torch and adjust the level of flame to be small enough to do the job but hot enough succeed. When the nut is cherry red in color, turn off the torch and remove it with the ratchet, extension, swivel, and socket or nut extractor. Carry on this procedure for the other four nuts.

    3

    Light the torch and cut the two or three bolts (some of the rear converters have a three-bolt inlet and some have two of the Rav4s) out of the rear flange. Cut them from the front converter side so you do not incur any damage to the rear converter. When the bolts are cut with the torch flush to the flange, turn off the torch, put on the safety gloves, and knock the rest of the bolt from the flange with a punch and hammer. Be ready to get out of the way or catch the front converter as it will drop out as soon as its free.

    4

    Allow the system to cool down. Install the top of the front converter with a new gasket to the manifold by threading on some new nuts by hand. Tighten them one at a time with the pneumatic gun, extension (either small or long), swivel, and socket until theyre tight.

    5

    Insert the gasket to the rear of the front converter flange connection and attach with the hardware (bolts, nuts, washers). Tighten with the gun, the small extension (if needed), swivel, and hold the head of the nuts in place with a hand wrench. Remove the cart and tools and any debris on the floor, lower the Rav4, and start it up to check for any possible exhaust leaks.

How to Replace a Toyota Rav 4 Rear Catalytic Converter

    6

    With the Rav4 raised on a lift, locate the oxygen sensor bolted to the rear converter. Follow the wire to the plug and separate it by unplugging it. You may need the screwdriver to press in the clip lock. As with the front converter, load the tools into the cart and have nearby.

    7

    Put on the safety glasses and light the torch with the striker. Cut the bolts from the front flange connection with the torch. Cut them from the rear converter side of the flange to avoid damage to the front converter flange. When the bolts are cut flush to the flange, turn off the torch and knock them out with a punch and hammer. Repeat this step for the rear converter to rear exhaust pipe flange. Be caul when the last bolt gets punched through. The converter will want to drop, but youll notice its still affixed to a rubber exhaust hanger. Remove the hook of the converter from the hanger.

    8

    Remove the bolts from the oxygen sensor studs. They may be deteriorated and you may need the extractor nuts to help you. Dont worry about the nuts or studs and damaging them. Youre going to replace the nuts and the studs are part of the converter. There will be new studs on the new converter. All you need is the oxygen sensor.

    9

    Insert the oxygen sensor into the new converter. Replace gasket (equipped with new converter) and nuts and tighten with the ratchet, extension, and a socket.

    10

    Place the hook on the new converter through the rubber hanger and attach the front flange to the front converter with gasket and hardware (bolts, washers, nuts). Attach the rear flange of the converter to the rear exhaust pipe flange with the gasket and hardware. Tighten the bolts and nuts with the gun, swivel, socket, and a hand wrench. Plug the oxygen sensor back into the plug. Remove the cart, tools, and any debris, lower the Rav4 and start the engine to check for any possible exhaust leaks.

ReadMore

Monday, February 24, 2014

Toyota RAV4 Battery Specifications

Toyota RAV4 Battery Specifications

The battery may be the most important part of your Toyota RAV4. The battery helps to run the engine, maintain the lighting system and power heating and cooling elements. The RAV4s battery specifications contain important dimensions, battery life and warranty details to prepare you for your next trip or commute.

Details

    The RAV4 battery is 7.68 inches wide by 5.16 long and 7.13 inches tall. The battery weighs 23.15 pounds and contains 12 volts of power. This includes 35 AH rate capacity. The bolt terminal type is an M8 nut. The battery is heat and vibration resistant. It also features a non-spillable design to avoid contact with battery acid. The batter can be mounted anywhere where the vehicle holds the battery housing.

Warranty

    Batteries such as the APW offer a labor and material warranty for 12 months. The APW brand offers an extended warranty for an extra cost. The Duralast is also a battery that can fit into a RAV4 and offers a standard one-year warranty similar to the APW. Extended warranties often cover the replacement of the battery but not labor for replacement.

Battery Replacement

    The Toyota RAV4 battery will last for about four years. High-quality batteries should be used if you own a recent model RAV4 because of added electrical features, including navigation systems and power outlets. Before replacing a battery, check the charging system. RAV4 batteries are available for model years 1986 to present.

ReadMore

Friday, February 21, 2014

How to Read Trouble Codes on a 1994 Toyota 4 Runner

How to Read Trouble Codes on a 1994 Toyota 4-Runner

You can read the trouble codes on your 94 Toyota 4-Runner from your home garage using a computerized handheld device known as an OBD scan tool. This tool can be purchased from your local auto parts retailer. The 4-Runner comes standard with an on-board diagnostics computer (OBD) that receives and stores trouble codes sent to it from sensors positioned throughout the vehicle. These sensors monitor all functions of the vehicle. Once these codes have been detected, the OBD computer illuminates a service or warning light on your instrument panel. You can read the codes yourself so you can pinpoint exactly what repairs need to be done.

Instructions

    1

    Find the OBD access port just left of the fuse panel cover on the drivers side dashboard. Plug the scan tool into this port, but do not force it in. If you force it, the pins could bend.

    2

    Put the key into the ignition and turn it to the "On" position, but do not crank the engine. This will power on most OBD scan tools. Note that scan tools vary depending on the manufacturer. Check your scan tools manual for exact instructions.

    3

    Wait for the scan tool to display "OK." Turn off the vehicle.

    4

    Press the "Menu" key on your scan tool and scroll through the menu using the arrow keys. Look for the "Stored Codes" option. Select this option. Wait while the scan tool displays the numerical trouble codes. Some scan tools will also display the diagnosis on the display, while others require that you look up the codes in the booklet that came with the scan tool.

    5

    Unplug the scan tool and have your vehicle repaired by a qualified mechanic.

ReadMore

Sunday, February 2, 2014

Tutorial on Replacing the Thermostat of a Toyota Tacoma

Tutorial on Replacing the Thermostat of a Toyota Tacoma

The thermostat in your Toyota Tacoma is an essential part of the trucks engine cooling system. The thermostat expands when the coolant in your engine becomes too hot, opening a valve that allows much more coolant to circulate through the system. The increase in coolant flowing through the radiator brings down the overall fluid temperature, and as a result, your trucks engine continues to operate within the optimal engine temperature. When the thermostat is no longer working properly, the engine overheats and the thermostat needs to be replaced.

Instructions

    1

    Remove the lower radiator hose by unscrewing the clamps and pulling off the hose.

    2

    Unscrew the two bolts on top of the thermostat.

    3

    Remove the thermostat and the gasket from the water pump.

    4

    Clean the thermostat housing, removing any dirt and leftover gasket pieces.

    5

    Line up the valve on the new thermostat with the point on the inlet, and place the new thermostat and gasket into the thermostat housing.

    6

    Screw the two bolts you removed earlier back into place.

    7

    Reattach the lower radiator hose and clamp it into place.

    8

    Top off the radiator with fresh coolant.

ReadMore

Monday, January 13, 2014

How To Find the Firewall Plug in a 1998 Toyota Tercel

The firewall in a 1998 Toyota Tercel is designed to protect the passengers from an engine fire. When you are building your own car stereo system for your Toyota Tercel, the firewall has small plugs that can be punctured to run wires through. In order to find these small plugs, you have to locate them on the firewall.

Instructions

    1

    Pop the Tercels hood by pressing the hood button inside the car.

    2

    Look inside the cars hood. Look for the large firewall, a large rectangle with rounded corners, behind the engine and just before the Tercels cab.

    3

    Find the rubber plug jetting out off the right side of the firewall. There will be only one plug coming out of the right side of the firewall. This is the firewall plug.

ReadMore

Sunday, December 15, 2013

How to Repair a 1998 Toyota Camry

How to Repair a 1998 Toyota Camry

The Toyota Camry, one of the most popular mid-size cars in the United States, boasts many safety features, and a range of options to fit almost any budget. The Camry is also well known among mechanics as an easily repairable car, making it that much more desirable. The 1998 Camry is no exception. Known for comfort and safety, this car needs little in the way of maintenance, and repairs tend to fall toward the inexpensive. With a set of mechanics tools and the right Chiltons manual, you can make many of these repairs yourself.

Instructions

Fixing a 1998 Toyota Camry

    1

    Gather information about 1998 Toyota Camrys. Read customer reviews and mechanic websites. Learn about the common problems and maintenance issues specific to a 1998 Camry. Gather maintenance schedules and information about tire sizes, oil types and other fluids that are specifically compatible with a 1998 Camry.

    2

    Inspect the car yourself. Test drive the car and listen for any strange sounds. Make note of any pulling or other motion-related disparities in the movement of the car. If possible, pop the hood and get underneath the car. Check for leaking fluids or broken parts.

    3

    Research any problem you notice. With the information you gathered from the inspection, look through your Chiltons manual, which describes how to fix any mechanical problem you may encounter with your car.

    4

    Consult with a mechanic, or begin the repair yourself, depending on the nature of the repair needed for the car. If you need to seek professional assistance, contact a mechanic that specializes in foreign cars, or better yet, one that specializes in Toyotas. If you are mechanically inclined or are facing a simple repair, you may choose to fix the vehicle yourself. Make sure you observe safety standards if you need to raise the car on jack stands, and use gloves to protect your hands. You can purchase parts for your Camry at most automotive stores or online. Keep your Chiltons manual close by for reference.

ReadMore

Tuesday, December 3, 2013

How to Replace an EGR Valve for 2000 Toyota RAV4

How to Replace an EGR Valve for 2000 Toyota RAV4

The exhaust gas recirculation (EGR) valve in your 2000 Toyota RAV4 is an exhaust intake regulator attached to the intake manifold of the engine. First introduced in the early 1960s, it regulates the mixture of fuel and exhaust (oxygen) entering into the engines combustion chambers. It operates by allowing measured amounts of exhaust to enter the combustion chamber, thus reducing the temperature within the chamber during combustion. It has become a vital part in improving fuel efficiency and reducing smog.

Instructions

    1

    Open the hood and locate the EGR valve, which is mounted on the left-rear of the intake manifold near the firewall. Leave the battery plug in, but use precaution not to contact the posts with any tools.

    2

    Disconnect the air intake tube leading to the inside-left fender well and attached to the intake manifold. This will provide for better access for replacing the EGR valve.

    3

    Unplug the single-prong electrical connection from the EGR valve by hand. Disconnect the rubber vacuum tube and inspect both of these parts for excessive wear or cracking. Replace these parts as necessary.

    4

    Remove the two EGR mounting bolts located on the valve using a socket wrench. Gently tap the valve to break the seal using a hammer or rubber mallet. Remove the old EGR valve and scrape away the old gasket using a paint scraper. Be careful not to allow any debris to enter the engine block.

    5

    Apply a thin bead of high-temperature-resistant gasket sealer onto the new gasket. Place the gasket with sealant down, directly onto the manifold opening. Do not to disturb the gasket placement, which can cause a void. Be sure that the mounting bolt holes are properly aligned so that the replacement valve will seat and mount properly.

    6

    Carefully install the new EGR valve into the manifold opening. Secure the valve in place with the two mounting bolts. Reattach the rubber vacuum tube and the single-prong electrical connection. Reconnect the air intake tube.

    7

    Disconnect both battery cables using a crescent wrench, which will reset the electrical system and check-engine light indicator. Keep the battery disconnected for at least six hours before reconnecting it. Then reconnect the battery, start the engine and check to see if the check-engine light remains off. Test the repair by turning the vehicle off and on several times while observing if the check-engine warning light comes on.

ReadMore

Tuesday, November 12, 2013

How do I Troubleshoot a Toyota SR5 FWD Pickup for Free

The Toyota SR5 FWD is a pickup track that allows people to haul or tow trailers, boats, or even other cars. If you are having problems with your SR5, there are a few things that you can do before you pay for a mechanic to look the vehicle over. Common issues are found in the battery, fuel tank, and the cooling system of the truck. You dont have to spend money to get your SR5 back on the road. You can do it yourself with little hassle.

Instructions

    1

    Insert your key into the SR5 and turn it so the electrical instrument panel lights up. Check over the fuel level in your trucks gas tank. If the fuel level is low enough for the truck not to start, fill the gas tank with fuel. If the instrument panel doesnt light up, you need to check your battery.

    2

    Pop the hood to the SR5 with the hood latch under the steering wheel. Open the hood and engage the hood rod to keep the hood up. Check over the battery connections. The battery is the black box with a black and red terminal coming off of it. Use a pair of insulated pliers to tighten the connection.

    3

    Clean the battery terminals if you find any corrosion on them. You can clean the terminals with a wire brush a little bit of soda. The carbonation from the soda will eat away the corrosion. Put the terminals back onto the battery and then try to restart the truck.

    4

    Check over the cooling system if you are having problems with your SR5 overheating. The coolant tank is on the left side of the engine block. Make sure that you have enough coolant so its up to the fill line on the side of the tank. Fill the coolant tank with enough coolant so it reaches the fill line.

    5

    Climb under the truck and locate the starter on the right side of the engine. This is a small black box. Have a friend turn the ignition. If you hear a buzzing noise from the starter, you need to have a professional replace it.

ReadMore

Monday, November 11, 2013

1997 Toyota Camry How to Change the Timing Belt

1997 Toyota Camry: How to Change the Timing Belt

If your 97 Camry is backfiring, sluggish or idles poorly then your timing belt may be bad. A timing belt ensures that the camshaft and crankshaft valves work together with the pistons, and having a broken or damaged timing belt can be hazardous to your car and very costly. Making sure that you have a properly working timing belt before things go very wrong can save you a lot of time and money in the end.

Instructions

Remove the timing belt

    1

    Disconnect the negative battery cable. Lift your car up with a jack and support it with jack stands. Remove the lower engine cover as well as the right inner fender cover. When youre done with that lower the car back to the ground.

    2

    From the top of the car, remove the bolts holding the alternator in place then pull out the alternator by hand. Take out the coolant reservoir.

    3

    Remove the serpentine belt by first removing the pivot bolt on the left corner of the engine block. Then loosen the tensioner adjustment bolt which is located under the tensioner pulley. Pull off the tensioner belt.

    4

    Raise the car back up and and take off the right engine mount. Keep the car raised.

    5

    Get your spark plug socket and remove the spark plugs.

    6

    Take off the timing belt cover. Line up the crankshaft pulley groove with the oil pump by rotating the engine to the right. Make sure the camshaft pulleys line up with the rear belt covers. You may have to rotate the engine.

    7

    Remove the crankshaft pulley bolt. Remove the tensioner and dust boot. Remove the bolts holding the lower timing belt cover on. Take the cover off.

Installing the timing belt

    8

    Clean the pulleys of any dirt, oil or water.

    9

    Align the new belts front mark with the crankshaft pulleys mark. Also align the timing belts installation mark with the camshaft pulley.

    10

    Install the pulleys. The easiest way to install them is, crankshaft, water pump, left camshaft, No. 2 idler, right camshaft and the No.1 idler.

    11

    Compress the tensioner until the push rod and housing holes align. Reconnect the dust boot and tighten the tension bolts up to 20 foot pounds.

    12

    Rotate the crankshaft and line up its groove with the oil pump. The timing marks on the camshaft and the marks on the rear timing cover should also match.

    13

    Put the timing belt guide in and tighten the bolts to 21 foot pounds. Replace and tighten the upper timing belt cover bolts to 74 inch pounds. Replace the lower timing belt cover bolts to 74 inch pounds.

    14

    Reinstall the spark plugs. Put back on the right engine mount, and reinstall the serpentine belt. To reinstall the serpentine belt follow the instructions in reverse on removing the belt. Put the coolant reservoir back in. Reinstall the alternator.

    15

    Put the inner fender back on along with the engine cover. Lower the car and reattach the negative battery cable. Start the car to make sure that the timing belt is working properly.

ReadMore

Tuesday, November 5, 2013

How to Find Toyota T 100 Axle Gear Ratio

The Toyota T100 was introduced 1993 and featured standard rear antilock brakes, along with a V6 engine. Styling, cab configurations and upgraded powertrain options followed in subsequent model years, until the Toyota Tundra replaced the T100 in 1998. Different axle ratios were available as factory option for certain model years. Determining the axle ratio for your Toyota T100 will allow you to order correct replacement parts or make informed decisions when making modifications to the drivetrain.

Instructions

    1

    Open the drivers side door and locate the VIN plate mounted on the lower door pillar for 1989 or newer models. Check the firewall, inside the engine compartment, for the VIN plate on vehicles older than 1989. The VIN plate contains important codes used to determine trim options, transmission and axle type.

    2

    Write down the four-character axle code listed on the VIN plate. For vehicles made before 1989, the axle code occupies the eighth through eleventh digit positions in the block of codes listed next to "C/TR/A/TM". Check for the four-character axle code positioned directly to "A/TM:" near the bottom of the VIN plate.

    3

    Navigate to the "Toyota Differential Identification" website (see Resources). Scroll to the "Toyota Differential Code Decoder" chart and cross-reference your vehicles axle code with the codes provided on the page. The second and third digits found within the axle code will determine the axle ratio for your vehicle.

ReadMore

Wednesday, October 30, 2013

Toyota Sienna Oxygen Sensor Removal

Toyota Sienna Oxygen Sensor Removal

Making its debut in 1998, the Toyota Sienna has always featured at least three oxygen sensors, due to the employment of its V-engine. A V-engine is shaped like a V and has an exhaust manifold on each side. Two upstream oxygen sensors monitor the fuel to air ratio before the exhaust hits the catalytic converter. Another sensor is installed in or to the rear of the converter to monitor its efficiency. If the Sienna features two converters, there will be four sensors installed on the minivan. One for each manifold and one for each converter.

Finding the Right Sensor

    When an oxygen sensor fails, it will trigger the malfunction indicator light (commonly known as the check engine light) on the instrument panel. Either read the diagnostic trouble code (DTC) with a scan tool or have it read at a local auto parts store. Most all scanners will reveal a DTC(s) with a letter and a number. This specific trouble code number can either be revealed with a brief description by the scanner or may have to be looked up in a on-board diagnostic trouble code list.

    Any code that reveals a "sensor 1" problem will indicate it is one of the upstream sensors near the manifold. "Sensor 2" codes will reveal the problem is in the downstream sensor near the converter.

    Bank locations are trickier, but not overly complicated. To locate "Bank 1, Sensor 1" simply find where the number one, three and five cylinders are on your Sienna. "Bank 2, Sensor 2" would indicate a problem with the downstream sensor on the number two, four and six cylinder side of the engine.

Replacing the Sensor(s)

    While its not a bad idea to replace all the sensors when one fails, sometimes its financially burdening. This is where finding the right sensor comes into play. The front and rear sensors are not the same part numbers and are not interchangeable.

    To replace the front sensor(s), lift the front end or the entire vehicle to gain access to the undercarriage of the exhaust system. Locate the sensor and disconnect the wire harness. Use a small screwdriver to depress the locking plug connection if necessary.

    Next, use a 22mm wrench or an oxygen sensor socket and suitable ratchet. Sometimes on the front sensors, its difficult to get one tool or another onto them, so use what works best for you. Spray the threads of the sensor with a copious amount of lubricant spray, such as WD-40 or PB Blaster and allow it to soak in for a few minutes. Use the wrench or ratchet to loosen the sensor by turning it counterclockwise. A box-end wrench would work best because an open-end wrench could mar the hex-head shape of the sensor. Simply insert the detached wire through the box-end of the wrench before applying it to the hex-head. The oxygen sensor socket uses a slit down the side of the socket that accommodates the wire. Once the sensor is loose enough, finish removing it by hand.

    The rear sensors are easier to access than the actual sensor, but Toyota places the plug connection under the carpet beneath the front seats. This requires opening the door and then removing the bottom door trim panel with a screwdriver. Set aside and reach underneath the carpet and towards the floorboard and then under the seat to obtain the plug. Once disconnected there, return to the undercarriage and simply pull the rubber gasket plug out from the floor board of the Sienna. The gasket holds the wire in place and prevents water from getting into the floor of the cab.

    Once the wire is released, remove the oxygen sensor as you would have or already did the front ones.

Universal or Direct-Fit

    There are two types of replacement sensors. Many companies try to promote the fact that youll save you money by purchasing universal sensors. These sensors require eliminating the plug connection on both sides of the wire harness. Next, match the wire colors up (which do not always match to the OEM wire harness) and butt connect. Since the rear sensors of the Sienna plug underneath the front seat and carpet, remove the seat to get enough room to perform this.

    Compare the prices of the direct-fit sensors before deciding to save money with the universal. You might even find the direct-fit ones cheaper or a couple bucks more.

ReadMore

Friday, October 18, 2013

2004 Toyota Camry Toe In Alignment Repair Specs

2004 Toyota Camry Toe-In Alignment Repair Specs

Sold in the majority of automotive markets throughout the world, Camry is a mid-sized family vehicle, manufactured by Toyota, since 1980. The factory specifications for the alignment are slightly different for all 2004 Camry models, though the toe specification is the same.

Toe Definition

    Toe is the difference between the leading and trailing inside edges of the front wheels. Wheel toe position out of specification can cause unstable steering and uneven tire wear.

Specifications

    The total toe-in specification should be 0 degrees with maximum allowable difference of 0.6 degrees. Rack end length difference should be 1.5 mm (0.069 inches), or less.

Notes

    These specifications are given for a vehicle at curb height with one-half tank of fuel. Also, the wheel toe position should be the final front wheel adjustment, performed after camber and caster adjustments.

ReadMore

Tuesday, October 15, 2013

How to Replace the Spark Plugs in a 2001 Toyota Tacoma

How to Replace the Spark Plugs in a 2001 Toyota Tacoma

The spark plugs on the 2001 Toyota Tacoma motor are designed to supply the spark needed to the combustion chamber during the combustion process. The spark ignites the gas fumes and causes the combustion which in return causes the piston to move up and down. When the engine is running, the coil sends the electrical current to the spark plugs that causes the plugs to spark. Over time the spark plus will begin to corrode around the spark base causing the plugs to misfire. Once this happens, change the spark plugs out immediately for maximum engine performance.

Instructions

    1

    Open the hood and locate the row of spark plugs on the driver side and passenger side of the engine. The 2001 Toyota Tacoma comes with basic spark plug wires on the driver side of the engine and ignition coil plugs on the passenger side of the engine. Start replacing the spark plugs on the driver side of the engine.

    2

    Pull the first spark plug wire off of the driver side spark plug closest to the front of the vehicle. Insert the deep-well socket and the six-inch extension onto the spark plug. Lock the ratchet onto the extension and turn the ratchet counter clockwise to loosen the spark plug. Remove the ratchet and finish unscrewing the plug with your fingers. Pull the spark plug out of the hole and discard it.

    3

    Screw the new spark plug into the hole with your hand until it stops turning. Continue to tighten the spark plug another half-turn with the ratchet, extension and socket to properly tighten the plug. Push the spark plug wire over the new spark plug until it locks on to the end of the plug. Move to the other driver side spark plugs and repeat the same process for replacing the plugs one plug at a time.

    4

    Move to the passenger side of the engine and unscrew the top of the ignition coil wire from the first spark plug closest to the front of the vehicle with your hand. Pull the wire off of the spark plug and insert the spark plug socket, extension and ratchet onto the plug. Turn the ratchet counter clockwise to loosen the plug. Remove the ratchet from the plug and finish unscrewing the plug with your hand. Pull the plug out of the hole and discard it.

    5

    Screw the new spark plug into the hole until it stops turning. Finish tightening the plug by turning the plug another half-turn with the ratchet, extension and socket. Push the ignition coil wire back onto the top of the spark plug wire and screw the top of the coil wire onto the spark plug clockwise until the end of the coil wire is tightened to the top of the spark plug. Move to the other passenger side spark plugs and repeat the same process for replacing the spark plugs one plug at a time.

    6

    Inspect all of the plugs and plug wires to ensure that all of the plug wires are securely attached to each spark plug. Crank the vehicle for about thirty seconds to test the operation of the new spark plugs. The engine should be running smoothly with the new spark plugs in place.

ReadMore

Thursday, September 5, 2013

1985 Toyota Corolla 1 6 Engine Specifications

The 1985 Toyota Corolla was part of the fifth generation of the vehicle. The cars had 1.4, 1.5 and 1.6 engines available. The 1.6 was first sold only in Japan and Europe, but made its way into the U.S. market during the year.

Engine Basics

    The 1.6-liter engine was used in the Corolla Coupe, and was considered somewhat of a sporty engine, from 1983 through 1987. It was a 96.9-cubic-inch, four-cylinder engine, mounted sideways in the car. The 1.6 had a bore and stroke of 3.19 and 3.03 inches. The bore and stroke relate to the size of the piston and the distance it travels.

Power

    The 1.6 engine had a compression ratio of 10-1, which is defined by how much the fuel and air mixture is compressed before ignition. This has a lot to do with how much power an engine produces. The 1.6 in the Corolla had 122 horsepower and 105 pound-feet of torque, which is pulling power.

Performance

    The 1.6 engine was slightly larger than most Corolla engines, and it performed a little better as well. It could go from zero to 60 miles per hour in eight seconds, which was good for a Corolla, a car not known for acceleration in its early years. It had a top speed of 122 mph. The cars gas mileage was 26.4 miles per gallon in the city and 31.7 mpg on the highway.

ReadMore