Monday, January 13, 2014
How To Find the Firewall Plug in a 1998 Toyota Tercel
The firewall in a 1998 Toyota Tercel is designed to protect the passengers from an engine fire. When you are building your own car stereo system for your Toyota Tercel, the firewall has small plugs that can be punctured to run wires through. In order to find these small plugs, you have to locate them on the firewall.
Instructions
- 1
Pop the Tercels hood by pressing the hood button inside the car.
2Look inside the cars hood. Look for the large firewall, a large rectangle with rounded corners, behind the engine and just before the Tercels cab.
3Find the rubber plug jetting out off the right side of the firewall. There will be only one plug coming out of the right side of the firewall. This is the firewall plug.
Tuesday, November 5, 2013
How to Find Toyota T 100 Axle Gear Ratio
The Toyota T100 was introduced 1993 and featured standard rear antilock brakes, along with a V6 engine. Styling, cab configurations and upgraded powertrain options followed in subsequent model years, until the Toyota Tundra replaced the T100 in 1998. Different axle ratios were available as factory option for certain model years. Determining the axle ratio for your Toyota T100 will allow you to order correct replacement parts or make informed decisions when making modifications to the drivetrain.
Instructions
- 1
Open the drivers side door and locate the VIN plate mounted on the lower door pillar for 1989 or newer models. Check the firewall, inside the engine compartment, for the VIN plate on vehicles older than 1989. The VIN plate contains important codes used to determine trim options, transmission and axle type.
2Write down the four-character axle code listed on the VIN plate. For vehicles made before 1989, the axle code occupies the eighth through eleventh digit positions in the block of codes listed next to "C/TR/A/TM". Check for the four-character axle code positioned directly to "A/TM:" near the bottom of the VIN plate.
3Navigate to the "Toyota Differential Identification" website (see Resources). Scroll to the "Toyota Differential Code Decoder" chart and cross-reference your vehicles axle code with the codes provided on the page. The second and third digits found within the axle code will determine the axle ratio for your vehicle.
Friday, October 4, 2013
How to Find a Key off Battery Draw
Sometimes its easy to figure out why your battery is dead because you left the lights on, or accidentally bumped an interior light as you got out and it went unnoticed. But, after the car is jumped and the battery dies again, its clear that you need a new battery or something else is drawing off the battery even when the car is off. Replacing the battery wont fix the problem if your car has a parasitic battery drain. Rather than a costly trip to the mechanic, find the source of the problem yourself with a multimeter, also known as an ammeter.
Instructions
- 1
Charge your car battery if your car doesnt start. Otherwise proceed to step 3.
2Let the car sit for at least 20 minutes after recharging the battery so the engine, lights and fuses will be cool.
3Turn off the radio, unplug any devices from the lighter socket like phone chargers or GPS units.
4Pop the hood. Remove the keys from the ignition. Check that all interior and exterior lights are off. Get out of the car and shut your door. Check that all the other doors are shut securely.
5Connect the meter to your cars battery per the manufacturers instructions. Once the meter is in series with the post and clamp, the display will show the current draw from the battery. Now, its time to go searching for the root of the problem.
6Pop the trunk. Touch the interior light. If the light is hot or warm, that means the light is staying on even when the trunk is closed.
7Open the glove box. Touch the interior light. If the light is hot or warm, that means the light is staying on even when the box is closed.
8Pull fuses methodically until you see the number displayed on the meter drop. This means youve found the source of the drain. Put each fuse back in the right socket after pulling it if you found the number didnt go down.
Sunday, September 22, 2013
How to Find a Chevrolet Motor Size
There are several reasons that you might need to know how to find a Chevrolet motor size. Two typical reasons are for ordering replacement parts or while finding replacement parts for your engine on another same-sized engine on a wrecked vehicle in a junkyard. In general, motor sizes are referenced by their cylinders, like 4 cylinder (V4), 6 cylinder (V6), or 8 cylinder (V8). There is another measurement referring to engine size that is important when replacing engines, the cubic inches (ci) displaced by the cylinders. A 3.6 Chevy engine displaces 3.6 liters or approximately 219ci.
Instructions
- 1
Open your glove box and remove the owners manual. In the index or glossary, look up engine and these pages will tell you all the specs (specifications) of your Chevrolet motor size.
2Pull the lever under your dashboard to pop the hood. Run your hand under the hood to find the latch that is present on some models of Chevy hoods that allow you to unlock and lift the hood.
3Look at the engine case. Some motors have the engine size, cylinders, and ci (cubic inches) or liters (1 liter is 1,000 cubic centimeters). For example, you might see V8 for an 8 cylinder or 3.6L for a 3.6-liter engine.
4Remove the valve cover and write down the code on the underside for the head numbers. Replace the valve cover securely. Use the code to find the matching motor size or compare the code to an engine chart like the Chevy big block engine charts found in the "references" below.