Pages

Showing posts with label 1. Show all posts
Showing posts with label 1. Show all posts

Sunday, April 13, 2014

How to Replace the Thermostat on the 3 1 Grand Prix

The cooling system inside of the Grand Prix 3.1-liter engines comes equipped with a spring-loaded thermostat that opens and closes according to the temperature of the antifreeze. The thermostat has a bottom spring that compresses and opens the top of the thermostat to allow the antifreeze to flow through the engine block. The main purpose of the thermostat is to prevent the engine from overheating by regulating the flow of the antifreeze through the engine. If the thermostat fails, it has a safety feature that will allow the thermostat to return to the open position.

Instructions

    1

    Pull the Grand Prix with the 3.1-liter engine into a safe and level work area. Set the emergency brake and open the hood. Shut the motor off and wait two to three hours for the engine to cool down completely.

    2

    Slowly unscrew the radiator cap and set it to the side. Make sure that the cap is not hot and does not have pressure on it. Slide the drip pan underneath the radiator drain plug on the bottom of the radiator. Loosen the drain plug with the pliers and allow a couple of gallons of coolant to drain into the drain pan. Tighten the drain plug back down tight.

    3

    Locate the top radiator hose that connects to the top radiator port and the intake manifold. The other end of the radiator hose connects to the thermostat housing on top of the intake manifold. Unscrew the hose clamp from the end of the hose that is attached to the thermostat housing port with the pliers. Pull the clamp back onto the hose. Twist and pull the hose off the thermostat housing port.

    4

    Unscrew the two thermostat housing mounting bolts with a ratchet and a socket. Pull the housing off and set it to the side. Pull the thermostat out of the intake manifold and discard it into the drain pan. Scrape away any of the old gasket from the base of the intake manifold and the bottom of the thermostat housing. Wipe away the excess gasket, dirt and debris from both places with a clean rag.

    5

    Spread a thin line of the red high-temperature silicone around the bottom of the thermostat housing. Push the gasket onto the bottom of the housing so that the silicone will hold the gasket in place and act as a extra sealer. Make sure that the bolt holes are matched up on the gasket and the thermostat housing.

    6

    Set the thermostat housing back over the intake manifold and match the bolt holes up. Screw the two mounting bolts through the thermostat housing and tighten with the ratchet and socket.

    7

    Push the top radiator hose back over the thermostat housing port and line the hose clamp over the radiator hose and the port. Tighten the clamp with the screwdriver until the hose is securely tightened to the thermostat housing port.

    8

    Add the antifreeze to the radiator until it is full. Leave the cap off the radiator. Crank the motor and let the engine heat up until the thermostat opens. The thermostat generally opens around 180 degrees. When the thermostat opens, the antifreeze level will drop inside of the radiator. Keep adding more antifreeze to the radiator until the antifreeze stabilizes at the top of the radiator cap. Screw the cap on tight and turn the engine off.

ReadMore

Tuesday, March 4, 2014

How to Fix a Cylinder 1 Misfire in a 1996 Saturn

Misfires are a common problem among cars, particularly older ones, when a lack of spark, fuel, air or compression occurs. Diagnosing and fixing a misfire takes skill because of the multiple components involved in the control of just one necessary element of combustion. Modern cars such as a 1996 Saturn have an on-board diagnostics system that can help find the source of the problem quickly if one is detected by a sensor. Misfires are characterized by a rough idle, reduction in power and poor riding comfort at speed and require immediate attention to avoid serious engine damage.

Instructions

    1

    Open the hood and disconnect the negative terminal from the battery using a wrench. Set it safely aside.

    2

    Hook up an on-board diagnostics scanner to the Saturns on-board diagnostics II port. This is usually located under the drivers steering wheel column on either side. Turn the car to accessory and enter the scan mode of the scanner. Search for codes indicating injector, fuel or air delivery failure and replace components as necessary. Also scan for oxygen sensor codes giving higher than normal readings; these indicate a possible spark delivery problem.

    3

    Remove the cylinder 1 spark plug with a socket set and check it for discoloration using a spark plug color chart. Dry plugs indicate a lack of fuel, while wet spark plugs indicate a lack of spark. Replace the spark plug with a new one, ensuring to coat the threads in anti-seize compound.

    4

    Inspect the cylinder 1 spark plug wires from the distributor to the spark plug for cracking and exposed metal. These change the resistance in the wire, causing spark failure. If replacement is necessary, order an entire set and replace all spark plug wires to maintain uniform resistivity to all cylinders. Also check the distributor for signs of wear and replace as needed.

    5

    Remove the cylinder 1 injector connector at the wiring harness and inspect for corrosion or wiring damage and repair as needed. Check the resistance of the injector by attaching multimeter clips to the injectors metal connectors and turning the multimeter to the 200-ohm setting. Compare with the manufacturers specification for that particular injector to ensure the electrical components are working.

    6

    Reinstall the cylinder 1 fuel injector clip. Remove the entire fuel rail with the injectors attached and coil wire. Turn the car over with the fuel rail off and inspect the spray pattern of the cylinder 1 injector. If a fine spray does not come from the injector, have it professionally cleaned or replace it.

    7

    Run a compression check whether the misfire continues. Use a compression tester specifically for car motors. Poor compression indicates a leak in the cylinder and will most likely mandate a check of the valve train or an engine rebuild.

ReadMore

Friday, January 17, 2014

How to Retrieve Codes for a Ford OBD 1

How to Retrieve Codes for a Ford OBD-1

Fords manufactured before 1996 come equipped with a first-generation On-Board Diagnostics computer (OBD-I) that retrieves and stores all error codes sent to it from various sensors throughout the vehicle. When these sensors detect a malfunction, they send the trouble code to the Fords computer, which turns on the vehicles warning and service lights. You can pull these codes right at home using a small device known as an OBD-I code reader, which you can purchase at any auto-parts retailer.

Instructions

    1

    Locate the diagnostic port on the drivers-side dash near the steering column. The port will be the same size and shape as the connector end of the OBD-I code reader.

    2

    Plug the code reader into the port.

    3

    Put the key into the ignition and turn it to the "II" position, but dont crank the engine.

    4

    Wait for the code reader to power on. Some readers have to be turned on, so you may have to find the "on/off" switch.

    5

    Select the command on the reader that says "Retrieve Codes" or something similar (the command will vary by brand). Wait while the code reader interfaces with the vehicles computer, then write the codes down on a piece of paper.

    6

    Look up the codes in the scanner manual. Unplug the reader and have the vehicle serviced or repaired based on the diagnosis obtained from the codes you retrieved.

ReadMore

Monday, November 18, 2013

How to Replace the Timing Belt on a 2002 Hyundai Accent 1 6L DOHC

The Accent is a subcompact car that Hyundai began manufacturing in 1994. The 2002 model is a second generation Accent, which includes the 1999 through 2004 models. Hyundai introduced a 4-cylinder, 1.6-liter engine with a double overhead camshaft in 2002. This engine uses a timing belt to drive the camshafts with the crankshaft, allowing the cylinder valves to open and close in the correct sequence. The timing belt in a 2002 Hyundai Accent lasts about 60,000 miles.

Instructions

    1

    Remove any components needed to access the cover for the timing belt. Disconnect the timing belt cover with a socket wrench.

    2

    Rotate the crankshaft clockwise to align the timing marks. The timing mark on the crankshaft sprocket must align with the timing mark on the front of the crankcase. The timing mark on the camshaft sprocket must align with the timing marks on the cap of the camshaft.

    3

    Loosen the tensioning bolt and pivot bolt on the timing belt tensioner with a socket wrench. Pull the tensioner towards the water pump as far as possible and tighten the adjusting bolt to hold the tensioner in place.

    4

    Align the timing marks for the crank shaft sprocket and camshaft sprockets, if necessary. Place the timing belt onto the crankshaft sprocket, camshaft sprocket, and belt tensioner wheel, in that order. Turn the camshaft sprocket counterclockwise to take up the slack in the timing belt. Turn the crankshaft clockwise to align the timing marks once again.

    5

    Loosen the mounting bolts for the timing belt tensioner with a socket wrench to place tension on on the timing belt. Ensure that all of the teeth on the camshaft sprocket engage the timing belt.

    6

    Tighten the adjusting bolt on the timing belt tensioner with a socket wrench. Torque the pivot bolt to between 15 and 18 foot-pounds with a torque wrench. Turn the crankshaft one full turn clockwise to seat the timing belt. Ensure that the timing marks on the crankshaft align once again.

    7

    Loosen the attaching bolts on the timing belt tensioner with a socket wrench to allow the tensioner to position itself. Adjust the tension on the timing belt by turning the tensioner wheel. The timing belt is at the correct tension when you pull the timing belt toward the water pump and the teeth of the timing belt come halfway across the tensioner adjusting bolt.,

    8

    Replace the covers for the timing belt. Install any components you removed in step one to access the timing belt.

ReadMore

Saturday, October 19, 2013

What Causes a Bank 1 O2 Oxygen Sensor to Fail

The oxygen sensors in your car perform several duties. Their primary function is to monitor and adjust your vehicles fuel mixture so that it gets the best possible fuel mileage while emitting the least amount of toxic emissions. Most vehicles have several oxygen sensors installed throughout the fuel system and engine, so the term "bank one" or "bank two" is used to identify the location of the sensor.

Age

    No car part is built to last forever, and that is true for oxygen sensors as well. Over time, normal wear and tear can cause your oxygen sensor to fail. Common causes include the gases from engine emissions and buildup of naturally occurring engine deposits.

Chemicals

    Oxygen sensors can be damaged by bad gas, leaded gas, internal coolant leaks, burnt oil and even products that have been applied to other parts of the engine to fix problems, such as gasket sealers. Oxygen sensors are really only meant to be exposed to good quality fuel, so other additives or chemicals can cause them to stop functioning properly.

Heating Circuit

    Most modern O2 sensors have an electrical heating circuit built into the sensor. If the electrical heating circuit malfunctions or fails, it is not uncommon for the entire oxygen sensor to fail.

ReadMore

Thursday, September 5, 2013

1985 Toyota Corolla 1 6 Engine Specifications

The 1985 Toyota Corolla was part of the fifth generation of the vehicle. The cars had 1.4, 1.5 and 1.6 engines available. The 1.6 was first sold only in Japan and Europe, but made its way into the U.S. market during the year.

Engine Basics

    The 1.6-liter engine was used in the Corolla Coupe, and was considered somewhat of a sporty engine, from 1983 through 1987. It was a 96.9-cubic-inch, four-cylinder engine, mounted sideways in the car. The 1.6 had a bore and stroke of 3.19 and 3.03 inches. The bore and stroke relate to the size of the piston and the distance it travels.

Power

    The 1.6 engine had a compression ratio of 10-1, which is defined by how much the fuel and air mixture is compressed before ignition. This has a lot to do with how much power an engine produces. The 1.6 in the Corolla had 122 horsepower and 105 pound-feet of torque, which is pulling power.

Performance

    The 1.6 engine was slightly larger than most Corolla engines, and it performed a little better as well. It could go from zero to 60 miles per hour in eight seconds, which was good for a Corolla, a car not known for acceleration in its early years. It had a top speed of 122 mph. The cars gas mileage was 26.4 miles per gallon in the city and 31.7 mpg on the highway.

ReadMore