Pages

Showing posts with label 1996. Show all posts
Showing posts with label 1996. Show all posts

Monday, November 17, 2014

How to Replace the Fuel Pump on a 1996 Ford Ranger

The Ford Ranger pickup truck comes with 2-wheel drive and 4-wheel drive transmissions. It may have a 6-cylinder 3.0L or a 6-cylinder 4.0L engine, and all versions of the Ford Ranger use electronic fuel injection. The fuel pump on this vehicle uses high pressure, and is located on the fuel tank. This makes it necessary to remove the fuel tank before replacing the fuel pump on a 1996 Ford Ranger.

Instructions

    1

    Relieve the pressure in the fuel system, and disconnect the fuel tank. Clean the area around the attaching flange for the fuel pump with a shop rag. This will prevent dirt from getting into the fuel tank when you replace the fuel pump.

    2

    Turn the locking ring on the fuel pump counter-clockwise with a locking ring removal tool. Remove the locking ring from the fuel pump. Disconnect the fuel pump assembly from the fuel tank, including the bracket. Remove the gasket for the fuel pump.

    3

    Apply a thin layer of heavy grease to the new fuel pump gasket, and install it into the ring groove on the fuel tank. Place the new fuel pump assembly into position in the fuel tank. Place the locking ring onto the fuel pump, and turn it clockwise until it locks into place.

    4

    Connect the fuel tank onto the vehicle, and put at least ten gallons of gas into the fuel tank. Fix any fuel leaks, and connect a pressure gauge to the throttle body valve. Turn the ignition on for three seconds without starting the engine, and turn it off for three seconds. Repeat this at least five times to pressurize the fuel system to at least 30 pounds per square inch, or PSI.

    5

    Check the vehicle and fix any leaks. Disconnect the pressure gauge, and start the engine. Check the vehicle again, and fix any leaks.

ReadMore

Thursday, May 15, 2014

How do I Remove Valve Covers on a 1996 7 3 Diesel

The valve covers sit on the top of the cylinder heads, and removing them will allow you access to the valves, springs, rocker arms, and push rods on your 7.3-liter Powerstroke Diesel. The 1996 7.3-liter was an optional engine in the Ford F250 and F350 Super Duty series trucks. The engine is very durable and has a good torque band, allowing it to pull heavy loads with little to no stress to the engine.

Instructions

    1

    Open the hood of your Ford truck and locate the negative battery cable end on the battery terminal. Loosen the clamp bolt on the battery cable end with a wrench then remove the cable from the battery and move it aside, isolating it from the battery.

    2

    Locate the retaining bolts along the perimeter of the valve covers on the top of the engine. There are eight of them on each valve cover.

    3

    Remove the eight retaining bolts, one at a time, with a socket and ratchet. Set the bolts aside as you will need them later.

    4

    Slide a putty knife or other flat, stiff tool under the edge of the valve cover and pry the cover loose from the head. Lift the valve cover straight off the cylinder head and set it aside. Repeat the process on the second valve cover if you are removing both covers.

ReadMore

Monday, May 12, 2014

How do I Replace the Fuel Pump on a 1996 Probe SE

The Ford Probe was a two-door coupe that Ford manufactured from 1989 to 1997. The 1996 model is a member of the second generation of Probes that includes the 1993 to 1997 models. Ford Probes may have a four-cylinder, 2.0-liter engine or a six-cylinder, 2.5-liter engine. All versions of this vehicle have multiport fuel injection, which requires a high-pressure fuel pump. You must remove the fuel tank of a Ford Probe in order to replace the fuel pump.

Instructions

    1

    Start the engine and remove the fuel-pump relay in the engine compartment. Allow the engine to stall and turn off the ignition. Replace the fuel-pump relay.

    2

    Drain the fuel tank and remove the cable from the negative battery terminal with a socket wrench. Raise the vehicle with a floor jack. Disconnect the exhaust pipe and exhaust-pipe insulator. Remove the electrical connectors and fuel lines from the fuel tank. Support the fuel tank with jack stands and disconnect the support straps for the fuel tank. Lower the fuel tank from the vehicle with the jack stands.

    3

    Detach the fuel lines from the fuel pump on the fuel tank. Turn the locking ring on the fuel pump counterclockwise with a brass drift and hammer. Disconnect the locking ring from the fuel pump and remove the fuel pump from the fuel tank. Discard the gasket.

    4

    Put the new gasket into position on the fuel tank and install the new fuel pump. Turn the locking ring for the fuel pump clockwise until the flange on the locking ring reaches the stopper. Connect the fuel lines for the fuel pump.

    5

    Connect the fuel tank to the vehicle and add at least 3 gallons of fuel to the fuel tank. Check the fuel system for leaks, and lower the vehicle. Connect the cable for the negative battery terminal with a socket wrench.

ReadMore

Tuesday, April 22, 2014

1996 Mustang Alignment Specs

1996 Mustang Alignment Specs

Ford introduced the Mustang in 1964 to compete with Chevrolets Corvette. The Mustang quickly became one of the most popular muscle cars ever made and went on to become an American icon. The Mustang has changed dramatically since those early years, in terms of both its appearance and its performance, but it is still one of most popular sports cars on the market.



The Mustang was redesigned in 1994 and kept that body style until it went through another major redesign in 1999, taking on a boxier, more aggressive style than the rounded-off body of the 1994 to 1998 models. In 1996, Ford put a new Borg-Warner T-45 Transmission in the Mustang, as well as a new 4.6-liter, modular engine, which is still used in the Mustang today.

General Alignment Information for the 1996 Ford Mustang

    The front end of 1996 Ford Mustang has a modified McPherson strut-design with shock struts and coil springs. The rear end has a solid-axle design, and its alignment cannot be adjusted. Problems with the alignment on the rear end are more likely due to bent or damaged parts.

    The front-end alignment specs are the same for all trims of the 1996 Mustang. (Reference 4)

    Always consult an owners manual or a certified mechanic before attempting to perform your own automotive repairs.

Caster Angle

    The limits for the caster angle for the front wheels of the 1996 Ford Mustang range from +2.65 to +4.15, with the ideal angle being +3.4 degrees.

Camber Angle

    The limits for the camber angle for the front wheels of the 1996 Ford Mustang range from 1.35 to +.15 for the left wheel and 1.35 to +.15 for the right wheel, with the ideal angle being -.6 for each wheel.

Toe-in

    The toe-in can range from 0 to +.24 inches.

Toe-out on Turns

    On the 1996 Ford Mustang, the toe-out on turns, measured by degrees, should be 19.84 for the outer wheel and 20 for the inner wheel.

ReadMore

Tuesday, March 25, 2014

How to Put on Belts in a BMW 1996 TI

The 1996 BMW 318 TI engine comes equipped with two different accessory belts that operate all of the engine accessories. The front belt is a single V-belt that operates the air conditioner compressor, and the back belt is a single serpentine belt that operates the power steering pump, cooling fan and the alternator. Both belts are tensioned inside of each accessory pulley by two separate belt tensioners. Excessive heat and wear can cause the belts to fray. Once the fraying becomes visible, replace the belt soon before it breaks.

Instructions

    1

    Open the hood and locate the belt tensioner for the air conditioner belt. The tensioner is mounted to the front of the engine block between the crankshaft and the a/c compressor. Use the tensioner pulley bolt to loosen the tension from the belt.

    2

    Position a 3/8-inch drive breaker bar and a metric socket onto the tensioner pulley bolt. Turn the breaker bar in a counter-clockwise motion to loosen the tension from the belt. Pull the belt out from around the tensioner pulley, the a/c pulley and the crankshaft pulley. Remove the belt from the engine well.

    3

    Locate the serpentine belt tensioner mounted to the front of the engine block on the lower left hand side of the alternator. Use the tensioner pulley bolt to loosen the tension from the belt.

    4

    Position a 3/8-inch drive breaker bar and a metric socket onto the tensioner pulley bolt. Turn the breaker bar in a counter-clockwise motion to loosen the tension from the belt. Pull the belt off the tensioner pulley and the remaining accessory pulleys. Remove the belt from the engine compartment.

    5

    Route the new serpentine belt around the accessories exactly as described by the belt routing diagram that is stamped to the top of the fan shroud. Once the belt is inside the accessory pulleys, turn the tensioner counterclockwise with the breaker bar and socket again and slide the belt around the tensioner pulley. Release the breaker bar and remove it from the tensioner.

    6

    Route the new air conditioner belt around the a/c compressor pulley and the crankshaft pulley. Turn the tensioner counterclockwise with the breaker bar and socket again. Slide the belt around the tensioner pulley and release the breaker bar. Remove the breaker bar from the engine compartment. Look over both belts to ensure they are seated inside of each accessory pulley.

    7

    Crank the engine for 10 to 15 seconds to completely seat the new belts inside the accessory pulleys. Turn the engine off.

ReadMore

Tuesday, March 4, 2014

How to Fix a Cylinder 1 Misfire in a 1996 Saturn

Misfires are a common problem among cars, particularly older ones, when a lack of spark, fuel, air or compression occurs. Diagnosing and fixing a misfire takes skill because of the multiple components involved in the control of just one necessary element of combustion. Modern cars such as a 1996 Saturn have an on-board diagnostics system that can help find the source of the problem quickly if one is detected by a sensor. Misfires are characterized by a rough idle, reduction in power and poor riding comfort at speed and require immediate attention to avoid serious engine damage.

Instructions

    1

    Open the hood and disconnect the negative terminal from the battery using a wrench. Set it safely aside.

    2

    Hook up an on-board diagnostics scanner to the Saturns on-board diagnostics II port. This is usually located under the drivers steering wheel column on either side. Turn the car to accessory and enter the scan mode of the scanner. Search for codes indicating injector, fuel or air delivery failure and replace components as necessary. Also scan for oxygen sensor codes giving higher than normal readings; these indicate a possible spark delivery problem.

    3

    Remove the cylinder 1 spark plug with a socket set and check it for discoloration using a spark plug color chart. Dry plugs indicate a lack of fuel, while wet spark plugs indicate a lack of spark. Replace the spark plug with a new one, ensuring to coat the threads in anti-seize compound.

    4

    Inspect the cylinder 1 spark plug wires from the distributor to the spark plug for cracking and exposed metal. These change the resistance in the wire, causing spark failure. If replacement is necessary, order an entire set and replace all spark plug wires to maintain uniform resistivity to all cylinders. Also check the distributor for signs of wear and replace as needed.

    5

    Remove the cylinder 1 injector connector at the wiring harness and inspect for corrosion or wiring damage and repair as needed. Check the resistance of the injector by attaching multimeter clips to the injectors metal connectors and turning the multimeter to the 200-ohm setting. Compare with the manufacturers specification for that particular injector to ensure the electrical components are working.

    6

    Reinstall the cylinder 1 fuel injector clip. Remove the entire fuel rail with the injectors attached and coil wire. Turn the car over with the fuel rail off and inspect the spray pattern of the cylinder 1 injector. If a fine spray does not come from the injector, have it professionally cleaned or replace it.

    7

    Run a compression check whether the misfire continues. Use a compression tester specifically for car motors. Poor compression indicates a leak in the cylinder and will most likely mandate a check of the valve train or an engine rebuild.

ReadMore

Tuesday, January 14, 2014

What Are Lifters on a 1996 Honda

What Are Lifters on a 1996 Honda?

Lifters in a car engine are part of the valve train, which operates the opening and closing mechanisms of the cylinders intake and exhaust valves. As the name suggests, they are the parts that physically lift and lower the plungers that allow the cylinder to "breathe."

Types of Lifters

    Lifters fall into three types: hydraulic, mechanical and roller. Hydraulic lifters, the most common, are filled with engine oil that pushes the lifter plunger up and down as it is compressed by the camshaft. Mechanical lifters are fixed metal pieces that push the lifter plunger as the camshaft moves. Roller lifters contain a roller in conjunction with either a hydraulic or mechanical mechanism to reduce friction.

96 Honda Lifters

    The lifters in a 96 Honda engine are hydraulic. The number of lifters in the engine depends on the Honda model and engine size in question.

Honda VTEC

    In 1989, Honda introduced a more efficient valve train mechanism called VTEC with an extra specially adapted cam and pin attached to each pair of lifters. The cam pushes the lifters to open the valves further at higher engine speeds to increase engine performance.

Replacement Lifters

    Replacement OEM (original equipment manufacturer) lifters and other parts for the valve train are readily available. Mechanics may also be able to suggest alternative parts that should work just as well.

ReadMore

Saturday, November 23, 2013

How to Replace the Glass Panel on the Mirror of a 1996 Suburban

If you want to replace just the glass panel in the mirror on your 1996 Suburban, youll be happy to know that you do not have to remove the large plastic housing that bolts onto the side of the Chevys door. The glass panel, which is actually made of plastic, is secured to the small motor mounted inside the plastic mirror housing. This makes replacing just the glass panel easier since no tools are required to disconnect the mirror from the motor in the housing.

Instructions

    1

    Push one side of the Suburbans glass panel mirror into the mirror housing. If youre replacing the mirror on the drivers side, push the right side of the mirror into the housing. If youre replacing the passengers side mirror on the Suburban, push the left side of the mirror into the housing.

    2

    Grasp the side of the mirror sticking out of the housing and pull hard on it to remove it. The mirror has a long metal tab that sticks out of the back of it. This tab slides into a slot in the face of the motor located inside the mirror. As you pull on the mirror, the metal tab will slide out of the slot on the motor.

    3

    Place the metal tab of the new glass panel mirror into the slot on the face of the mirrors motor.

    4

    Push on the face of the mirror to push the metal tab into the slot. Once the mirror rests inside the housing, the mirror is in place.

ReadMore

Sunday, November 17, 2013

How to Remove the Fuel Pump in a 1996 GMC Yukon

The GMC Yukon is a full-size sport utility vehicle. The 1996 model has a standard 8-cylinder, 5.7-liter engine with sequential fuel injection. The fuel pump in this vehicle must maintain a high level of pressure in the fuel system. The fuel pump is mounted in the fuel tank, so you must remove the fuel tank before you can remove the fuel pump.

Instructions

    1

    Disconnect the negative battery terminal with a socket wrench to prevent the unintentional discharge of fuel. Open the fuel tanks filler cap to relieve the pressure in the fuel tank. Siphon as much fuel from the fuel tank as possible with a hose. Drain the fuel into a gasoline container.

    2

    Raise the vehicle with a floor jack and support it on jack stands. Disconnect the filler neck and fuel vent tube from the fuel tank. Support the fuel tank with a transmission jack and remove the support straps for the fuel tank with a socket wrench.

    3

    Lower the fuel tank slightly with the transmission jack so you can disconnect the electrical wiring and fuel hoses to the fuel tank. Disconnect the fuel tank from the vehicle and move it to a work area.

    4

    Turn the locking ring on the fuel pump assembly counterclockwise with a hammer and brass punch. Remove the locking ring and pull the fuel pump assembly from the fuel tank. Detach the fuel pump from the rest of the fuel pump assembly.

    5

    Pull the fuel pump away from its bottom support without damaging the rubber insulator or fuel strainer. Pull the fuel pump out of the rubber connector after it is clear of the bottom support.

ReadMore

Friday, November 15, 2013

How to Replace the Oil Sending Unit on a 1996 Grand Cherokee

Located on the passengers side of the engine block, the oil pressure sensor in your 1996 Jeep Grand Cherokee converts engine oil pressure to milliamps and sends this information to the engine management computer. Whether your Jeep has a 4.0-liter inline six cylinder or a 5.2-liter v-8, the sensor sits in nearly the same place on the engine block. Sensor failures can exhibit as erratic readings at the oil pressure gauge on the instrument panel or a low pressure indicator light flashing on and off randomly. You can replace the sensor in minutes, and a new sensor is available from Jeep or through a parts store.

Instructions

    1

    Open the hood of your Jeep and locate the negative battery cable end at the battery. Loosen the clamp bolt on the cable end with a wrench then separate the cable from the battery terminal. Isolate the cable end away from the battery while you work.

    2

    Locate the oil pressure sensor on the passenger side of the engine, near the oil filter housing. The sensor threads into the engine block and has an electrical connector on the top of it with a single wire coming off it.

    3

    Release the locking tab on the electrical connector then pull the connector off the sensor and lay it aside. Slide a deep socket over the sensor, connect a ratchet to it and rotate the sensor counterclockwise until it is free of the engine block. Discard the old sensor.

    4

    Position the new sensor in the engine block, rotating it clockwise by hand until it is snug. Place the socket and ratchet on the sensor then carefully turn it another 1/4-turn to secure it.

    5

    Push the electrical connector on to the new sensor until the locking tab engages. Move back to the battery and position the negative battery cable end onto the battery terminal. Tighten the clamp bolt with a wrench then close the hood.

ReadMore

Wednesday, October 16, 2013

How to Change the Fuel Pump in a 1996 Chevy Van 1500

The 1996 Chevrolet C1500 may refer to a truck or a van. The power plant for both vehicles is an eight-cylinder, 5.7L engine, which uses fuel injection. This means that the fuel pump for this vehicle pumps fuel into the engine under high pressure. The fuel pump for the 1996 Chevy is located in the fuel tank, so you must remove the fuel tank in order to replace the fuel pump.

Instructions

    1

    Relieve the pressure in the fuel tank by loosening the fuel filler cap. Disconnect the cable for the negative battery terminal with a socket wrench. Raise the rear of your vehicle with jack stands and drain the fuel tank. Remove the fuel tank.

    2

    Locate the fuel pump assembly on top of the fuel tank. Turn the locking ring for the fuel pump assembly counterclockwise with a drift punch and hammer. Pull the fuel pump assembly away from the fuel tank and disconnect the fuel pump from the rest of the fuel pump assembly.

    3

    Pull the fuel pump away from the bottom support and pull it into the attaching hose. Pull the fuel pump out of the connector. Ensure you dont damage the fuel strainer and insulator while removing the fuel pump. Remove the O-ring.

    4

    Install a new O-ring on the fuel pump assembly. Attach the new fuel pump to the hose without twisting the fuel strainer. Place the fuel pump assembly into the fuel tank and turn the locking ring for the fuel pump clockwise until its tight.

    5

    Install the fuel tank and lower the vehicle with the jack stands. Connect the cable to the negative terminal of the battery. Tighten the fuel filler cap.

ReadMore

Sunday, October 6, 2013

How to Replace a Timing Belt on a 1996 Nissan Pathfinder

The Nissan Pathfinder is a sport utility vehicle in production since 1986. The 1996 model was the first of the second generation Pathfinders, which Nissan produced until 2004. Nissan introduced the VG33E engine with the 1996 Nissan Pathfinder, which is a six-cylinder, 3.3-liter engine with a single overhead camshaft. This engine has a timing belt to synchronize the movement of the crankshaft and camshaft. It is essential for the engine to be in the correct position when replacing the timing belt.

Instructions

    1

    Disconnect the cable from the negative terminal with a socket wrench. Remove the engine undercover and the radiator shroud. Disconnect the cooling fan assembly, including its pulleys. Drain the radiator and detach the radiator hose. Disconnect the radiator.

    2

    Detach the drive belts for the power steering motor, air conditioner and alternator. Disconnect the spark plugs with a socket wrench, and remove the dust shield for the distributor. Detach the intake tube near the cover of the cylinder head. Disconnect the hose from the thermostat.

    3

    Remove the crankshaft pulley bolt with a socket wrench and disconnect the pulley with a gear puller. Remove the front covers for the timing belt. Rotate the crankshaft clockwise to align the timing mark on the crankshaft sprocket with the timing mark on the oil pump housing. Align the timing mark on the camshaft sprocket with the timing mark on the rear timing belt cover.

    4

    Install the bolt for the crankshaft pulley bolt with a socket wrench. Turn the timing belt tensioner counterclockwise with a hexagon wrench to relieve the pressure on the timing belt, and remove the timing belt.

    5

    Disconnect the covers for the cylinder heads with a socket wrench, and loosen the retaining bolts for the rocker arm shaft. Turn the timing belt tensioner clockwise with a hexagon wrench to tighten it. Tighten the locking nut for the tensioner to hold it in place.

    6

    Install the timing belt onto the crankshaft and camshaft so that the arrow on the timing belt points toward the front timing belt covers. Align the white lines on the timing belt with the timing marks on the crankshaft and camshaft. Loosen the locking nut on the belt tensioner with a hex wrench to turn the tensioner about 75 degrees clockwise, and tighten the locking nut.

    7

    Turn the crankshaft clockwise by several turns to seat the timing belt, and align the timing marks. Press timing belt between the camshaft sprocket and tensioner pulley with about 22 lbs. of force as you loosen the locking nut for the timing belt tensioner.

    8

    Turn the crankshaft clockwise to advance the timing belt by about 2.5 teeth, and tighten the locking nut for the tensioner. Turn the crankshaft clockwise by several full turns and align the timing marks again.

    9

    Replace the front covers for the timing belt, and tighten their mounting bolts to 24 foot-pounds with a torque wrench. Install the crankshaft pulley onto its shaft, and torque its mounting bolt to between 90 and 98 foot-pounds. Attach the hose to the thermostat housing, and connect the air intake to the cylinder head cover.

    10

    Connect the dust protector for the distributor with a socket wrench, and install the spark plugs. Attach the drive belts for the power steering motor, air conditioner and alternator. Connect the radiator and attach the hose from the water pump. Fill the radiator with coolant and replace the cooling fan assembly. Connect the undercover for the engine. Start the engine and correct any fluid leaks.

ReadMore