Tuesday, March 18, 2014
How to Remove the Light Switch From the Panel in a 2008 Dodge Dakota
The headlight switch assembly on the dash of your 2008 Dodge Dakota does more then just turn the lights on and off; do not put off replacing a faulty switch. The switch controls the interior lights, the dash lights, parking or running lights and the headlights. A faulty switch will often cause other functions to fail; if the switch fails altogether, youll find yourself with no headlights at all and unable to drive your truck. Look for replacement switches at any auto parts retailer or your local Dodge dealer.
Instructions
- 1
Locate the retaining screws on the instrument panel of your Dakota, remove them with a Phillips screwdriver and set them aside. Pop the bezel off the instrument panel using a flat-blade screwdriver. Set the bezel aside for safekeeping.
2Locate the three retaining bolts on the face of the headlight switch assembly---two on the outboard edge and one on the inboard side---then remove them using a socket and ratchet. Set the bolts aside for reuse during installation.
3Slide the headlight switch assembly forward until you can reach the electrical connector on the rear of the assembly. Press the locking tab in on the connector, and separate the connector from the rear of the headlight switch. Pull the headlight switch out of the dash, and discard it.
4Slide the new headlight switch assembly into the dash far enough to allow the electrical connector to reach it. Push the connector onto the back of the switch, ensuring that the locking tab engages completely.
5Push the switch in place, and install the three retaining bolts. Tighten the bolts with a socket and ratchet until they are just snug enough to hold the switch securely but wont crack its plastic casing.
6Position the instrument panel bezel in place, snapping it into the retaining clips. Install the retaining screws and tighten them with a Phillips screwdriver only until they are just snug enough not hold the bezel in place without damaging it.
7Turn on the headlight switch, and cycle the headlights through the high- and low-beam positions several times to ensure a successful repair.
Saturday, November 23, 2013
How to Replace the Glass Panel on the Mirror of a 1996 Suburban
If you want to replace just the glass panel in the mirror on your 1996 Suburban, youll be happy to know that you do not have to remove the large plastic housing that bolts onto the side of the Chevys door. The glass panel, which is actually made of plastic, is secured to the small motor mounted inside the plastic mirror housing. This makes replacing just the glass panel easier since no tools are required to disconnect the mirror from the motor in the housing.
Instructions
- 1
Push one side of the Suburbans glass panel mirror into the mirror housing. If youre replacing the mirror on the drivers side, push the right side of the mirror into the housing. If youre replacing the passengers side mirror on the Suburban, push the left side of the mirror into the housing.
2Grasp the side of the mirror sticking out of the housing and pull hard on it to remove it. The mirror has a long metal tab that sticks out of the back of it. This tab slides into a slot in the face of the motor located inside the mirror. As you pull on the mirror, the metal tab will slide out of the slot on the motor.
3Place the metal tab of the new glass panel mirror into the slot on the face of the mirrors motor.
4Push on the face of the mirror to push the metal tab into the slot. Once the mirror rests inside the housing, the mirror is in place.
Wednesday, October 23, 2013
How to Remove the Tailgate Inside the Panel on a 1994 Corolla Wagon
The seventh generation of the Toyota Corolla includes the 1993 through 1997 model years in the United States and features a few different models, including a four-door station wagon. This model has a tailgate that lifts up and allows direct access to the rear of the vehicle. To remove the tailgate in the 1994 Corolla station wagon you must also remove the trim panel for the tailgate.
Instructions
- 1
Open the tailgate and raise it as far as possible. Remove the fasteners for the inner trim panel with a socket wrench. Remove the inner panel from the tailgate by pulling it forward and then out of the vehicle.
2Detach the electrical wiring harness from the the tailgate and push it out of your way. Mark the location of the hinges on the tailgate with a scribe to help you position the tailgate if you must reinstall it later.
3Disconnect the bolts for the damper stays with a socket wrench. Remove the damper stays from the tailgate and move them out of the way.
4Detach the electrical wiring for the rear defroster, if your vehicle is so equipped. Remove the mounting bolts for the tailgate with a socket wrench and detach the tailgate from its hinges.
Sunday, October 13, 2013
How to Remove the Seat Belt Panel on a 94 Mustang GT
The Ford Mustang was introduced in 1964. The 1994 Ford Mustang was available in GT and Cobra trim levels. The GT variant was equipped with a 3.8-liter V-6 capable of producing 145-horsepower. The famous 5.0-liter V-8 was optional for 1994 Mustang GT, and could produce 215 horsepower. Removing or replacing the seat belt panel on the 1994 Mustang GT requires work on the body of the vehicle. This project should be carried out by someone with prior mechanical knowledge. Removing the seat belt panel involves the removal of a safety device, which should be re-installed by a professional mechanic.
Instructions
- 1
Open the door of the Mustang. Slide the seat as far forward as it can go, then release the back of the seat to tilt it forward. Locate and remove the two screw caps on the vertical door rail, near the door catch, using a flat-head screwdriver. Remove the two bolts beneath the caps with a ratchet and socket.
2Push the front edge of the back seat back and release it from the clips. Pull the front lip of the seat upwards -- you may have to get in on both sides of the car and use your knee to push the seat back, to release the clips. Tilt the front of the seat up and remove the back seat from the Mustang.
3Remove the cover from the speaker on the seat belt panel by gently prying it off with a flat-head screwdriver. Remove the three Philips screws that hold the speaker to the panel. Pull the speaker out of the panel, and pull the speaker wires free from the back of the speaker, by hand. Set the speaker out of your work area.
4Remove the 15-mm bolt from the base of the seat belt panel, using a ratchet and socket. Allow the bottom of the belt to retract through the slot in the panel. Gently pry the panel loose from the side of the Mustang, using a putty knife wrapped in a towel. Slide the putty knife along the edges until you hit a clip, then pry the panel free from that clip -- the rest of the panel is held on by multiple body clips. Pry the panel free from all of the clips, then remove the panel from the Mustang.
5Install the panel into the car, and align the panel with the clips underneath. Gently tap the panel with the side of your fist or a rubber mallet, starting in the center-rear of the panel. Pull the bottom of the seat belt through the panel, then install the seat belt mounting bolt in the floor, by hand. Turn the bolt a couple of threads to temporarily hold the belt in place.
6Tap the edges of the panel to install the panel on the rest of the body clips. Tighten the seat belt mounting bolt back into the bottom of the seat deck, using a 1/2-inch drive torque wrench and socket. Tighten the bolt between 25 and 34 foot-pounds. Install the speaker wires back onto the rear speaker. Insert the speaker into the panel and tighten the screws snug with a Phillips screwdriver -- no torque is needed on the speaker screws; adding torque can crack the panel.
7Install the rear side of the back seat under the vertical seat cushion. Push the front edge of the seat back and down to clip it into the floor of the car -- you may have to enter both sides of the vehicle and use your knee to push the seat back enough to engage the clips. Lift up on the front lip of the seat with your fingers to make sure that you have the seat clipped in. Repeat this step until both sides of the back seat are securely fastened.
8Install the two screws into the panel near the door catch, on the vertical door jamb. Tighten the screws snug with a ratchet and socket. Install the screw caps.