Monday, November 17, 2014
How to Replace the Fuel Pump on a 1996 Ford Ranger
The Ford Ranger pickup truck comes with 2-wheel drive and 4-wheel drive transmissions. It may have a 6-cylinder 3.0L or a 6-cylinder 4.0L engine, and all versions of the Ford Ranger use electronic fuel injection. The fuel pump on this vehicle uses high pressure, and is located on the fuel tank. This makes it necessary to remove the fuel tank before replacing the fuel pump on a 1996 Ford Ranger.
Instructions
- 1
Relieve the pressure in the fuel system, and disconnect the fuel tank. Clean the area around the attaching flange for the fuel pump with a shop rag. This will prevent dirt from getting into the fuel tank when you replace the fuel pump.
2Turn the locking ring on the fuel pump counter-clockwise with a locking ring removal tool. Remove the locking ring from the fuel pump. Disconnect the fuel pump assembly from the fuel tank, including the bracket. Remove the gasket for the fuel pump.
3Apply a thin layer of heavy grease to the new fuel pump gasket, and install it into the ring groove on the fuel tank. Place the new fuel pump assembly into position in the fuel tank. Place the locking ring onto the fuel pump, and turn it clockwise until it locks into place.
4Connect the fuel tank onto the vehicle, and put at least ten gallons of gas into the fuel tank. Fix any fuel leaks, and connect a pressure gauge to the throttle body valve. Turn the ignition on for three seconds without starting the engine, and turn it off for three seconds. Repeat this at least five times to pressurize the fuel system to at least 30 pounds per square inch, or PSI.
5Check the vehicle and fix any leaks. Disconnect the pressure gauge, and start the engine. Check the vehicle again, and fix any leaks.
Thursday, May 15, 2014
How to Replace the Fuel Pump in a 97 Lumina Car
The Chevrolet Lumina is a series of coupes, minivans and sedans manufactured from 1990 to 2001. The replacement fuel pump for these vehicles depends on the engine, which may be a six-cylinder 3.4 L engine or a 3.1 L engine. All versions of the 1997 Lumina have sequential fuel injection, meaning that the electric fuel pump on these vehicles uses high pressure to deliver fuel to the fuel injectors. You can access the fuel pump on most 1997 Luminas through a removable access panel in the trunk.
Instructions
- 1
Disconnect the negative battery cable with a socket wrench, and remove the engine cover. Relieve the pressure in the fuel tank by loosening the filler cap for the fuel tank. Remove the cap for the fuel pressure port on the fuel rail, and connect special tool J 34730-1A to the fuel pressure port. Place the bleed hose for this special tool into a gasoline container. Open the valve on the special tool to bleed the fuel in the fuel system into the gasoline container.
2Drain the fuel tank to 1/4 of its capacity, and remove the jack, spare tire and spare tire cover from the trunk. Take out the trunk liner, and unfasten the retaining nuts for the access panel with a socket wrench. Remove the panel, and disconnect the electrical connector for the fuel pump.
3Clean the fuel sender assembly with a shop rag, and disconnect the quick-connect fittings from the fuel sender assembly. Remove the retaining snap ring on the fuel sender assembly with a socket wrench, so that the fuel sender assembly springs up. Remove the fuel sender assembly without handling the fuel pipes. Discard the old O-ring and clean the sealing surfaces for the O-ring.
4Place the new O-ring on the fuel tank and install the new fuel sender assembly onto the fuel tank. Avoid folding the fuel strainer and ensure that the fuel strainer does not impede the movement of the float arm for the fuel gauge after the installation is complete.
5Replace the retaining snap ring for the fuel sender assembly, and turn the snap ring clockwise with a socket wrench until it fully seats with the fuel tanks tab slots. Attach the electrical connector and quick-connect fittings to the fuel sender assembly. Connect the cable for the negative terminal on the battery, and fasten the filler cap for the fuel tank.
6Turn the ignition switch for 2 seconds, then turn it off for 10 seconds. Turn the ignition back on and check for leaks in the fuel system. Replace the access cover in the trunk and tighten the retaining nuts to 96 inch-pounds. Replace the trunk liner, jack, spare tire and spare tire cover.
Monday, May 12, 2014
How do I Replace the Fuel Pump on a 1996 Probe SE
The Ford Probe was a two-door coupe that Ford manufactured from 1989 to 1997. The 1996 model is a member of the second generation of Probes that includes the 1993 to 1997 models. Ford Probes may have a four-cylinder, 2.0-liter engine or a six-cylinder, 2.5-liter engine. All versions of this vehicle have multiport fuel injection, which requires a high-pressure fuel pump. You must remove the fuel tank of a Ford Probe in order to replace the fuel pump.
Instructions
- 1
Start the engine and remove the fuel-pump relay in the engine compartment. Allow the engine to stall and turn off the ignition. Replace the fuel-pump relay.
2Drain the fuel tank and remove the cable from the negative battery terminal with a socket wrench. Raise the vehicle with a floor jack. Disconnect the exhaust pipe and exhaust-pipe insulator. Remove the electrical connectors and fuel lines from the fuel tank. Support the fuel tank with jack stands and disconnect the support straps for the fuel tank. Lower the fuel tank from the vehicle with the jack stands.
3Detach the fuel lines from the fuel pump on the fuel tank. Turn the locking ring on the fuel pump counterclockwise with a brass drift and hammer. Disconnect the locking ring from the fuel pump and remove the fuel pump from the fuel tank. Discard the gasket.
4Put the new gasket into position on the fuel tank and install the new fuel pump. Turn the locking ring for the fuel pump clockwise until the flange on the locking ring reaches the stopper. Connect the fuel lines for the fuel pump.
5Connect the fuel tank to the vehicle and add at least 3 gallons of fuel to the fuel tank. Check the fuel system for leaks, and lower the vehicle. Connect the cable for the negative battery terminal with a socket wrench.
Sunday, May 4, 2014
How to Replace the Fuel Pump on a 1991 Cougar
The Mercury Cougar is a model of car manufactured by the Lincoln-Mercury division of Ford Motor Company. The 1991 Mercury Cougar is a full-size coupe that belongs to the seventh generation of these vehicles. It may have a six-cylinder 3.8L engine or an eight-cylinder 5.0L engine. The fuel pump in a 1991 Mercury Cougar attaches to the fuel tank, so replacing the fuel pump requires you to remove the fuel tank.
Instructions
- 1
Disconnect the cable from the negative terminal on the battery with a socket wrench. Loosen the cap on the fuel tank and remove the cap for the fuel pressure relief valve on the fuel rail. Connect fuel pressure gauge T80L-9974-A to the relief valve and place its drain hose in a gasoline container. Open the pressure gauge and drain the fuel from the fuel system into the container. Disconnect the fuel pressure gauge.
2Raise the vehicle and support its rear end with jack stands. Siphon as much fuel from the fuel tank as possible and disconnect the filler hose from the fuel tank. Remove the exhaust pipe and exhaust shields from the fuel tank. Place a floor jack under the fuel tank and place a plank of wood on top of the fuel tank. Disconnect the nuts for the retaining strap on the fuel tank and lower the fuel tank slightly so you can disconnect the fuel lines electrical wiring from the fuel tank. Remove the air deflector from the retaining straps of the fuel tank. Lower the fuel tank and remove it from the vehicle.
3Clean the area around the retaining flange for the fuel pump on the fuel tank. Turn the locking ring for the fuel pump counterclockwise and detach the locking ring. Disconnect the fuel pump and bracket from the fuel tank and discard the seal ring.
4Clean the mounting flange for the fuel pump and the groove for the seal ring on the fuel tank. Apply a thin layer of grease to the new seal ring and place the seal ring into the groove on the fuel tank. Connect the new fuel pump and bracket to the fuel tank without damaging the fuel filter. Align the keys on the fuel pump with the holes on the mounting bracket. Install the locking ring to the fuel pump so that the locking tabs on the locking ring are under the ring tabs on the fuel tank. Turn the locking ring clockwise until it reaches the limit of its travel.
5Connect the fuel tank to the vehicle and lower the vehicle. Put at least 10 gallons of fuel in the fuel tank. Install a fuel pressure gauge on the relief valve and connect the negative battery cable with a socket wrench. Turn the ignition on for three seconds at a time until the fuel pressure reaches 35 psi. Remove the pressure gauge and cover the relief valve with the cap. Start the engine and check for fuel leaks.
Tuesday, April 29, 2014
How to Tell If Your Fuel Pump Is Broken
The fuel pump is an essential component of a vehicle. Fuel is pumped from the fuel tank to the engine. Without a functioning fuel pump, adequate fuel pressure cannot be delivered to the engine. This will cause problems such as hard starting, rough idle, misfiring, hesitation and stalling and can even prevent the car from starting . This may happen at the most inconvenient time. If you suspect that your fuel pump is broken, there are certain tests that you can perform to confirm it.
Instructions
- 1
Listen for a humming sound that normally occurs when the key is turned to the "Start" position. Turn the key in the ignition to the "Start" position and listen for a humming sound from the fuel tank. A hum means that the pump is in working condition.
2Check if your fuel pump is broken by doing a static fuel test. Turn the key in the ignition to the "on" position. Look at the fuel pressure gauge to detect movements. The fuel pressure should immediately come up and stay steady. If it doesnt, that can indicate that there is a defect in the fuel pump.
3Connect a voltage meter to the wires that connect to your fuel pump. Connect the voltage meter to the green wire. The fuel pump wires are located under the vehicle, behind the drivers door. Let someone start the engine while the voltage meter is connected to the wire. A normal reading is between 10 to 11 volts. If there is a zero reading, this usually mean that the fuel pump is bad.
Saturday, April 12, 2014
Will a Car Run Without a Power Steering Pump Belt
Some car owners wonder if a vehicle can operate without a power steering pump belt or if this function is safe. Not replacing a PSP belt may save money and hassle at first, but it will eventually cause huge problems.
Function
The movement of the engine drives the PSP belt. The belt then transfers engine power to the PSP itself, which puts power steering fluid under pressure. This pressurized fluid amplifies steering wheel movement to make steering the car effortless.
Removal
Removal of the PSP belt stops the pumps function, and eliminates power steering. Technically, a car could be driven without a PSP belt, but its not a recommended practice.
Warning
With power steering disabled, the steering wheel becomes much less responsive and more difficult to operate. Without the circulation of power steering fluid, the steering mechanism will lose lubrication over time, ultimately causing the entire steering system to fail, endangering the life of the driver and others.
Tuesday, April 8, 2014
How to Replace a 1993 Buick Century Fuel Pump
The Buick Century is a mid-size car manufactured by the Buick division of General Motors. The 1993 model belongs to the fifth generation of the Century, produced from 1982 to 1996. The engine in a 1993 Buick Century may be a four-cylinder 2.2L engine or a six-cylinder 3.3L engine. Both of these engines use fuel injection, requiring a high-pressure fuel pump. The fuel pump in the 1993 Buick Century attaches to the fuel tank, which you must remove in order to replace the fuel pump.
Instructions
- 1
Loosen the filler cap of the fuel tank and raise the the vehicle on jack stands. Disconnect the electrical connector from the fuel pump and lower the vehicle. Start the engine and allow it to run until the engine stalls. Crank the engine for three seconds to consume any remaining fuel in the fuel lines.
2Disconnect the cable for the negative battery terminal with a socket wrench. Raise the vehicle on jack stands and drain the fuel tank. Detach the electrical wiring from the fuel tank, including the ground wire under the body of the vehicle. Disconnect the fuel lines from the fuel tank. Support the fuel tank with a jack stand and remove the nuts on the fuel tanks retaining strap with a socket wrench. Lower the fuel tank with the jack stand and remove it from the vehicle.
3Disconnect the fuel filter from the fuel pump by twisting it and pulling it off the fuel pump. Discard the fuel filter. Detach the electrical connector for the fuel sending unit and remove the fuel sending unit from the fuel tank. Pull the fuel pump from its mounting bracket on the fuel sending unit.
4Install the new fuel pump onto the fuel sender assembly between the mounting bracket and the pulsator. Connect the electrical connector for the fuel sender assembly. Place the fuel filter into position on the fuel pump and push the fuel filter until it is fully seated.
5Install the fuel sending unit onto the fuel tank and connect the fuel tank. Check the fuel system for leaks and connect the battery cable to the negative terminal of the battery with a socket wrench.
Monday, March 10, 2014
How to Remove the Power Steering Pump Pulley on a Dakota
Dodge Dakotas use a rack-and-pinion power steering system. This system uses a pump to drive power steering fluid to the rack-and-pinion. A pulley that runs on the accessory drive belt powers the pump. If the pulley is damaged, the pump will not move fluid into the steering system and the pulley must be replaced. In order to replace the pulley, you must first remove it from the power steering pump.
Instructions
- 1
Locate the diagram on the underside of your hood that depicts the drive belt routing. Use this diagram to help locate your idler pulley. This will be the lower of the two pulleys on the far right.
2On the left-hand side of the idler pulley assembly, locate the tension adjusting bolt. Using a wrench, loosen the bolt until you can move the idler pulley assembly enough to relieve tension on the drive belt.
3Locate the power steering pump pulley. This is the uppermost of the two pulleys on the far right, located above the idler pulley. Remove the drive belt from around the pulley.
4Place the pulley puller on the power steering pulley. Place the arms of the puller behind the pulley and align the threaded end with the center of the pulley. Turn the nut on the shaft by hand until it is tight.
5Place a socket and ratchet on the bolt head end of the pulley puller. Hold the ratchet in place and place a wrench on the nut you hand-tightened in Step 4. Turn the wrench counterclockwise to move the threaded shaft into the power steering pulley.
6Continue to turn the nut until the pulley comes loose from the power steering pump. Remove the pulley from the engine compartment and turn the nut clockwise until the puller shaft comes free of the pulley.
Saturday, March 8, 2014
How to Install a Fuel Pump in a 1984 GMC S 15
The 1984 GMC S-15 truck with the six-cylinder, 2.8-liter engine is carbureted instead of fuel-injected. As such, the fuel pump on this truck is mounted on the side of the engine block and driven by a cam on the camshaft. If the fuel pump isnt working properly, you can experience poor performance, stalling, and even backfiring. You can change the fuel pump n the 1984 S-15 in about an hour to two hours in your front yard.
Instructions
- 1
Slide the jack under the front frame cross member, and lift the truck until there is enough room for you to comfortably slide under.
2Place the jack stands under the frame behind both front wheels, and caully lower the truck onto them. Remove the jack.
3Slide under the truck, and locate the pump on the lower left front side of the engine. Tag the fuel lines if they are both threaded fittings so you know which line goes where.
4Remove the fuel lines from the pump. Most fuel pumps will have two threaded fittings; remove these using the flare nut wrenches and turning the fittings counterclockwise. If either of the connections has a rubber hose clamped to it, squeeze the clamp with the pliers, and slide it back on the hose a few inches. Grasp the fuel line, and twist and pull it off the pump nipple.
5Remove the bolts securing the fuel pump to the block by turning them counterclockwise with the ratchet and socket. Remove the fuel pump by pulling it away from the engine.
6Clean the block side mating surface of all remnants of the old gasket using the gasket scraper.
7Apply a thin bead of RTV sealant to both the block and pump mating surfaces. Apply the gasket to block mating surface.
8Hold the new fuel pump in place, and insert the bolts in the bolt holes, and turn them clockwise by hand. Tighten these bolts to 15 foot-pounds with the ratchet and socket.
9Reattach the fuel lines to the pump. For threaded fittings, thread the fittings into the new pump by turning them clockwise by hand. Tighten the fittings to 15 foot-pounds using the flare nut wrench. If so equipped, slip the rubber fuel line over the nipple. Squeeze the clamp, and slide it over the nipple.
10Slide the jack back under the front cross member, and lift the truck off the jack stands. Remove the jack stands, and lower the truck. Start the truck, and verify there are no leaks.
Monday, February 24, 2014
How to Change the Fuel Pump in a 1993 Dodge Spirit
The Dodge Spirit is a mid-size sedan manufactured from 1989 to 1995. Most 1993 models have a four-cylinder, 2.5-liter engine that uses throttle-body injection, or TBI. TBI is an early form of fuel injection developed in the 1980s that used low fuel pressure, typically in the range of 10 to 15 pounds per square inch. The fuel pump on the 1993 Dodge Spirit is integrated with the fuel sender into a single unit. The replacement of the fuel pump on this vehicle requires you to disconnect the fuel tank.
Instructions
- 1
Disconnect the cable to the batterys negative terminal with a socket wrench to prevent an accidental spark from the battery. Drain the fuel in the fuel tank by siphoning the fuel into a gasoline container. Raise the vehicle with a jack, and support it on jack stands. Remove the fuel tank from the vehicle. Squeeze the retainer tabs on the fuel supply line and fuel return lines. Disconnect these fuel lines from the fuel pump module.
2Remove the mounting bolts from the fuel pump module with a socket wrench. Disconnect the wiring on top of the fuel pump module, and remove the nut for the fuel pumps lower bracket with a socket wrench. Remove the hose clamp from the fuel pump, and disconnect the outlet hose from the fuel pump. Remove the clamp for the inlet hose on the fuel pump, and disconnect the inlet hose.
3Tilt the fuel pump to avoid damage to the float arm and fuel filter. Remove the lower gasket. Remove the fuel pump from the faceplate of the fuel tank. Remove the lower bracket and upper gasket from the fuel pump.
4Place the new upper gasket onto the new fuel pump. Connect the fuel pump to the upper bracket and outlet hose. Attach the hose clamp to the outlet hose. Place the new lower gasket into the lower bracket, and fasten the bolt for the lower bracket with a socket wrench. Connect the inlet hose to the fuel pump, and attach its hose clamp. Connect the electrical wiring for the fuel pump.
5Install the fuel pump module so the filter on the fuel pump module fits into the tray on the fuel tank. Align the bottom gasket so its holes align with the corresponding holes on the fuel tank. Attach the fuel pump module to the fuel tank by tilting it as necessary to clear the float arm and fuel filter. Use a socket wrench to fasten the fuel pump module to the fuel tank with the mounting bolts.
6Connect the fuel supply line and fuel return line to the fuel pump module. Install the fuel tank, and lower the vehicle. Fill the fuel tank with fuel, and connect the cable for the batterys negative terminal with a socket wrench. Start the engine, and check for fuel leaks.
Friday, February 7, 2014
How to 1998 Chevy Metro Fuel Pump Replacement
Suzuki markets the Suzuki Cultus under a variety of names, including the Chevrolet Metro, Geo Metro and Suzuki Swift. The engine for the 1998 Chevy Metro is a four-cylinder 1.3-liter engine with multiport fuel injection. This type of fuel injection requires the fuel pump to deliver fuel under high pressure. The fuel pump for the 1998 Chevy Metro is in the fuel tank, so you must remove the fuel tank when you replace the fuel pump.
Instructions
- 1
Open the cap for the fuel tank, and remove the control relay in the fuse box. Start the engine, and allow it to stall. Crank the engine for a few seconds to ensure no fuel remains in the fuel system. Disconnect the cable on the negative terminal of the battery with a socket wrench to ensure you dont accidentally start the engine.
2Remove the rear seat cushion, and disconnect the electrical wiring for the fuel gauge in the bottom of the rear seat. Raise and support the vehicle on jack stands. Disconnect the fuel line from the fuel filter, and connect the open end of the fuel line to a hose. Siphon the fuel from the fuel tank into a gasoline container.
3Disconnect the hoses for the fuel pipes on the fuel tank. Detach the fuel filler hose and breather hose from the fuel tank. Support the fuel tank with jack stands, and disconnect the mounting bolts for the fuel tank with a socket wrench. Lower the fuel tank from the vehicle.
4Release the clamps for the fuel hoses to the fuel pump assembly. Remove the mounting screws for the fuel pump assembly with a socket wrench, and detach the electrical connector for the fuel pump. Lift the fuel pump assembly and gasket from the fuel tank.
5Install the new fuel pump by reversing steps 1 through 4. Fill the fuel tank, and turn on the ignition to pressurize the fuel system. Start the engine, and check for fuel leaks.
Wednesday, February 5, 2014
How to Replace the Water Pump in a 1997 Caravan 3 3L
The Caravan is a family minivan manufactured by Chrysler under its Dodge brand since 1984. The 1997 Model is a third-generation Caravan that had a choice of several different engines, including a 6-cylinder 3.3-liter engine. This engine uses a belt-driven water pump to circulate coolant around the engine. If you need to replace the water pump in a 97 Caravan, you must access it from underneath the vehicle.
Instructions
- 1
Remove the cable from the negative terminal of the battery with a socket wrench. This will prevent you from starting the engine during the water pump replacement procedure. Place a drain pan under the drain plug for the radiator and open the drain plug. Allow the coolant to drain into the drain pan.
2Remove the serpentine drive belt with a socket wrench. Raise the vehicle with a jack and support it on jack stands. Disconnect the right front wheel and the lower shield on the right front fender.
3Disconnect the pulley for the water pump with a socket wrench. Remove the mounting bolts for the water pump and detach the water pump from the engine. Discard the O-ring for the water pump and clean the mounting surface for the O-ring with a shop towel.
4Place the new O-ring onto its mounting surface on the new water pump. Install the new water pump onto the engine and tighten its mounting bolts to 108 in. lbs. with a torque wrench. Install the pulley for the water pump and tighten its mounting bolts to 20 ft. lbs.
5Connect the lower shield for the right front fender with a socket wrench and install the right front wheel. Connect the lug nuts for the right front wheel and torque them to 95 ft. lbs. with a torque wrench. Lower the vehicle and connect the serpentine drive belt. Fill the radiator with a mixture of 50 percent water and 50 percent ethylene glycol antifreeze.
6Connect the cable to the negative battery terminal with a socket wrench. Start the engine and allow it to run until the thermostat opens. Turn the engine off and allow it to cool. Check and correct any leaks in the coolant system.
Thursday, January 23, 2014
What Is a Smog Pump
A smog pump is a crucial piece of equipment used for helping to reduce emissions. It is one of the systems found in automobiles that helps fuel burn cleaner.
Air Injection
The smog pump is the common term for the secondary air injection system (or just air injection system). After combustion occurs, the exhaust gases must leave the combustion chamber through a port. The air injection system pumps fresh oxygen into the exhaust port, causing the exhaust gases (hydrocarbon and carbon monoxide) to continue to burn and theore deplete more efficiently. On some vehicles, it also supplies air to the catalytic converter. The system usually consists of an air pump, a diverter valve, an air distributor and a check valve.
Air Pump
The air pump is what creates the force of the air to push fresh air into the system. It is run by a belt or electric motor.
Diverter Valve
The diverter valve is used by some cars to keep too much air from entering the system when the vehicle is decelerating, reducing backfiring and limiting air pressure.
Air Distributor
The air distributor is known as the air management valve or air distribution manifold. This valve switches the flow of air direction to point toward either the exhaust manifold or toward the catalytic converter, depending on the operating conditions of the vehicle.
Check Valves
Check valves prevent exhaust air from flowing into the system and causing possible damage.
Sunday, December 8, 2013
How to Change the Fuel Pump on a 95 Ford 7 3 Diesel
An 8-cylinder 7.3-liter diesel engine is one of the engines that Ford uses in full-size pickup trucks. This engine is most common in the F-250 3/4-ton and F-350 full-ton pickup truck. The fuel system for this engine requires the fuel pump to deliver fuel under high pressure. The fuel pump for this engine is located in the engine compartment on top of the engine. A turbocharged engine will also require you to remove the turbocharger prior to replacing the fuel pump.
Instructions
- 1
Disconnect the banjo bolt for the fuel line on the fuel pump with a socket wrench. Remove the fittings for the fuel line at the rear of the cylinder heads and discard the old seal rings. Release the clamps for the fuel pump lines on the front of the fuel pump and detach the fuel lines.
2Disconnect the drain hose from the fuel filter and remove the fuel filter with a socket wrench. Loosen the retaining bolts for the fuel pump retaining bolts and pull the fuel pump from the crankcase. Discard the O-ring and disconnect the tappet of the fuel pump from the crankcase bore.
3Connect the fuel pump tappet to the base of the new fuel pump and replace the O-ring on the fuel pump. Install the new fuel pump into the crankcase and fasten the mounting bolts with a socket wrench.
4Install the fuel filter and fasten its mounting bolts with a socket wrench. Attach the drain hose to the fuel filter and connect the fuel lines to the front of the fuel pump. Tighten the clamps on the fuel line and install new seal rings on the rear of the fuel pump.
5Install the fittings for the fuel lines towards the rear of the cylinder heads without tightening them. Install the banjo bolt onto the fuel pump and tighten it to 40 ft. lbs. with a torque wrench. Tighten the fittings for the fuel line with a socket wrench.
Tuesday, November 26, 2013
How to Use a Bicycle Pump to Fill an Air Tank
Compressed air is useful for many things. It can pump up flat tires, run a variety of air tools, or simply be used to clean a bit of dirt out of a crevice. In order to create and use compressed air you need to have a commercial air compressor or an air tank. If you have an air-tank equipped with a pressure gauge and Schrader valve you can easily fill it up with a bike pump.
Instructions
- 1
Press the bike pump connection onto the Schrader valve located near the top of the air tank. It will be an approximately 3/8 inch metal threaded tube with a small pin in the center.
2Pump up the tank while keeping an eye on the tank air valve. After several dozen pumps you should start to see some air pressure registered. Continue this action until the tank reads about 20 pounds of pressure.
3Remove the bike pump nozzle and use the tire gauge to verify the pressure for safety. Once it is verified, continue pumping to your desired pressure.
Wednesday, November 20, 2013
How to Replace the Water Pump on a 1994 Chevrolet K1500
A Chevrolet K1500 is a pickup truck with four-wheel drive and a nominal carrying capacity of 1/2 ton. The 1994 model belongs to the fourth generation of this series, which was in production from 1988 to 2000. The water pump in the 1994 Chevrolet K1500 attaches to the front of the engine and is accessible from the engine compartment. The replacement of the water pump in this vehicle also requires you to drain the cooling system and remove additional components from the engine.
Instructions
- 1
Disconnect the cable to the negative battery terminal with a socket wrench to ensure you dont inadvertently start the engine. Put a drain pan under the radiator and open the radiator drain. Allow the coolant to drain from the radiator and replace the radiator drain plug.
2Disconnect the drive belts on the engine with a socket wrench and remove the alternator. Disconnect the cooling fan assembly, including the clutch and pulley. You might also need to remove some accessory brackets to access the water pump. Remove the radiator hose and heater hose from the water pump. Disconnect the bypass hose from the water pump if your vehicle has a 7.4-liter engine.
3Use a socket wrench to remove the mounting bolts that attach the water pump to the timing chain cover. Detach the water pump from the timing chain cover and discard the water pumps gasket.
4Clean the timing chain cover with a shop towel to remove any traces of the old gasket. Install the new water pump and gasket to the timing chain cover. Tighten the mounting bolts for the water pump to 30 ft. lbs. with a torque wrench.
5Connect the hoses to the water pump. Install the alternator and any other components you removed to access the water pump. Connect the drive belts to their respective pulleys. Fill the radiator with coolant and connect the cable for the batterys negative terminal.
Sunday, November 17, 2013
How to Remove the Fuel Pump in a 1996 GMC Yukon
The GMC Yukon is a full-size sport utility vehicle. The 1996 model has a standard 8-cylinder, 5.7-liter engine with sequential fuel injection. The fuel pump in this vehicle must maintain a high level of pressure in the fuel system. The fuel pump is mounted in the fuel tank, so you must remove the fuel tank before you can remove the fuel pump.
Instructions
- 1
Disconnect the negative battery terminal with a socket wrench to prevent the unintentional discharge of fuel. Open the fuel tanks filler cap to relieve the pressure in the fuel tank. Siphon as much fuel from the fuel tank as possible with a hose. Drain the fuel into a gasoline container.
2Raise the vehicle with a floor jack and support it on jack stands. Disconnect the filler neck and fuel vent tube from the fuel tank. Support the fuel tank with a transmission jack and remove the support straps for the fuel tank with a socket wrench.
3Lower the fuel tank slightly with the transmission jack so you can disconnect the electrical wiring and fuel hoses to the fuel tank. Disconnect the fuel tank from the vehicle and move it to a work area.
4Turn the locking ring on the fuel pump assembly counterclockwise with a hammer and brass punch. Remove the locking ring and pull the fuel pump assembly from the fuel tank. Detach the fuel pump from the rest of the fuel pump assembly.
5Pull the fuel pump away from its bottom support without damaging the rubber insulator or fuel strainer. Pull the fuel pump out of the rubber connector after it is clear of the bottom support.
Thursday, November 14, 2013
How to Remove a Windshield Washer Pump in a 2000 GMC Jimmy
The washer pumps in a 2000 GMC Jimmy are located on the outside edge of the washer fluid reservoir, next to the right-side fender. These electric pumps draw fluid from the reservoir and force it through rubber tubes that connect to the washer jet nozzles. Over time, the small motors inside these pumps wear out and fail, rendering the washer fluid system inoperable. In order to replace these pumps, the washer reservoir must be removed from the vehicle.
Instructions
Removal
- 1
Shut down the engine and pop open the hood. Open the washer fluid reservoir cap and draw the fluid out of the reservoir and into a bucket with a hand pump.
2Disconnect the electrical connectors and hoses from the washer pumps near the bottom of the reservoir.
3Remove the screw holding the reservoir to the vehicle with a ratchet and metric socket.
4Lift up on the reservoir and remove it from the vehicle. Remove each from the reservoir by gently pulling and twisting it until it pops loose from its rubber grommet.
Installation
- 5
Install each new pump into the reservoir by pressing it into the rubber grommet, using a twisting motion, until it is fully seated.
6Set the reservoir into position inside the engine compartment and reinstall its retaining screw. Torque the screw to 27 inch-pounds, using a torque wrench.
7Reconnect the hoses and electrical connectors to both pumps.
8Place a funnel inside the reservoir fill hole and refill the reservoir to the appropriate level, then test the pumps.
Wednesday, November 13, 2013
How Do I Install a Fuel Pump in a 1990 Ford Ranger
The Ranger is a pickup truck that Ford has produced since 1983. The 1990 Ford Ranger was equipped with either a 6-cylinder 2.9-liter engine or a 6-cylinder 4.0-liter engine, each of which uses fuel injection. The Ranger has an electric fuel pump in the fuel tank that produces low pressure. The pump is part of the fuel gauge sending unit, and you have to remove the entire unit if you need to replace the fuel pump and install a new one.
Instructions
- 1
Loosen the cap on the fuel tank and remove the air filter. Disconnect the cable from the negative battery terminal. Remove the valve cap from the pressure relief valve on the fuel rail. Connect fuel pressure gauge tool T80L-9974-A to the pressure relief valve. Open the pressure relief valve to relieve the pressure in the fuel system. Disconnect the fuel pressure gauge and replace the valve cap.
2Drain the fuel from the fuel tank. Support the fuel tank with jack stands. Release the clamp on the fuel tanks fill pipe. Disconnect the bolts for the skid plate and remove the skid plate and its brackets from the fuel tank. Disconnect the bolts for the front and rear straps of the fuel tank and remove the straps. Release the clamp for the fuel sender units fuel hose. Remove the fuel lines from the fuel sender unit. Lower the tank from the Ranger with the floor jacks. Remove the shield from the fuel tank.
3Detach the electrical connector from the fuel system sender unit. Clean the fuel tank around the fuel sender unit with a shop rag. Turn the locking ring on the fuel sender unit counterclockwise with a hammer and brass drift. Remove the locking ring from the fuel sender unit and pull the fuel sender unit from the fuel tank. Discard the sealing gasket. Detach the fuel pump from the fuel sender unit.
4Insert the new fuel pump into the fuel sender unit. Put a new sealing gasket on the fuel tank. Place the fuel sender unit into the fuel tank and align the fuel senders tabs with the fuel tanks slots. Attach the locking ring to the fuel sending unit and turn it clockwise until the ring tab is against the stop. Attach the electrical connector for the fuel sender unit.
5Reinstall the fuel tank. Reconnect the negative cable on the battery. Turn the ignition on for five seconds, then turn it off. Repeat at least five times to pressurize the fuel system. Start the engine and check for fuel leaks.
Sunday, November 10, 2013
Installing a Fuel Pump on a 97 Chrysler Sebring LXi
Like the first generation of Sebring Convertibles, the 1997 Chrysler Sebring LXI has a Mitsubishi 2.5L V6 engine with fuel injection. The fuel-injection system operates under very high pressure supplied from the gas tank by the fuel pump. Replacing the fuel pump on the LXI is a different procedure than other Sebring models, but fortunately, is well within the capabilities of even a novice mechanic.
Instructions
- 1
Relieve fuel tank pressure by opening the gas filler cap. Inside the car, pull upward on the rear seat cushion to disengage it from its retaining hooks and remove the cushion from the vehicle. Of the two access panels underneath the cushion, remove the one on the right.
2Disconnect the wiring harness that attaches to the fuel pump. Turn the ignition and allow the engine to run until it dies from a lack of fuel system pressure. This permits safe removal of the fuel pump. Once the fuel pressure has been released, disconnect the negative battery cable.
3Remove the hose connecting the fuel pump to the fuel rail. Remove the mounting bolts holding the fuel pump in place and lift the pump out of the fuel tank. Wrap the pump in shop towels to catch remaining gasoline and relocate the pump to a well-ventilated area.any
4Place the new fuel pump into the fuel tank by carefully aligning the pump with the slots in the tank until the pump is securely seated. Reinstall the mounting bolts (22 inch-pounds of torque) and reconnect the hose leading to the fuel rail. Reinstall the access panel and seat cushion.
5Make sure that the gas filler cap has been reinstalled and reconnect the negative battery terminal. Turn the ignition to the "On" position for a few seconds to allow the fuel system to build pressure, then start the engine to confirm proper operation.