Pages

Showing posts with label use. Show all posts
Showing posts with label use. Show all posts

Wednesday, April 9, 2014

How to Use a U Joint C Frame Press Service Kit

A C-frame U-joint press kit is not something that most homeowners have in their toolboxes. In the past, if someones U-joint needed replacement, the vehicle had to go into the shop for service. Today, auto parts stores are renting and lending specialized tools for the do-it-yourself mechanic. Among tools available for rent are brake caliper kits, specialized wrenches and C-frame U-joint press service kits. Having access to this kit makes replacing U-joints something that a vehicle owner may accomplish in a home garage.

Instructions

Removing U-Joints with the C- Clamp U-Joint Press Kit

    1

    Clean all grease and grime away from the yoke.

    2

    Remove the snap ring bearing cap retainers by inserting the tips of snap ring pliers into the holes on the snap ring and squeezing the handle of the pliers together to unseat the rings from the grooves in the yoke. Pull the snap rings out.

    3

    Slip a receiving cup --- taken from the service kit and large enough to allow removal of the bearing cap from the yoke but small enough to be in full contact with the yoke --- into the open end of the C-clamp with the open end of the cup facing the inside of the C-clamp.

    4

    Slide an anvil onto the end of the forcing screw on the other side of the C-clamp. Ensure that the anvil is small enough to pass through the yoke of the U-joint.

    5

    Position the U-joint press over the yoke. Tighten the forcing screw by hand until the anvil sits on the bearing cap and the cup is firmly on the yoke over the bearing cap on the opposite side.

    6

    Tighten the forcing screw clockwise with an adjustable wrench until the bearing cap on the cup side is out of the yoke.

    7

    Turn the clamp around 180-degrees. Tighten the forcing screw by hand until the anvil is firmly against the solid portion of the U-joint and the cup is in position to receive the other bearing cap.

    8

    Tighten the forcing screw until the other bearing cap is free from the yoke. Repeat the steps for the other two bearing caps.

Installing U-Joints with the C-clamp U-joint press kit

    9

    Remove the receiving cup from the U-joint press. Remove the bearing caps from a replacement U-joint and set them aside. Ensure that the needle bearings inside the bearing cap remain on the sides of the bearing caps.

    10

    Slide the solid portion of the U-joint into the yoke so that two of the opposite ends are in the two holes in the yoke. Move the solid portion to one side in the yoke and insert a bearing cap over the end. Tap the bearing cap lightly with a hammer to get it started into the hole in the yoke.

    11

    Position the U-joint press over the yoke so that the anvil is in contact with the bearing cap. Hand-tighten the forcing screw until the other side of the C-clamp is firmly in contact with the yoke. Tighten the forcing screw, pressing the bearing cap into the hole in the yoke. Keep pressing the cap into the yoke until the groove for the snap ring is clearly visible.

    12

    Move the solid center of the U-joint to the other side of the yoke far enough that a bearing cap can be partially inserted on the end, but not so far that it comes out of the first bearing cap. This ensures that the needle bearings inside the caps do not fall out of place.

    13

    Turn the clamp around 180 degrees and position the anvil on the second bearing cap. Hand-tighten the forcing screw until the other side of the C-clamp is solidly against the yoke. Press the second bearing cap into the other hole in the yoke by turning the forcing screw until the groove for the snap ring retainer is visible, ensuring that the solid center of the U-joint does not come out of either bearing cap. Repeat for the other bearing caps. Reinstall the snap rings.

ReadMore

Friday, March 21, 2014

How to Use a Truecraft Torque Wrench

A Truecraft torque wrench allows you to tighten a bolt to a specific torque value. Most automotive repair jobs require that you secure bolts to a certain torque value, measured in foot-pounds or inch-pounds. Too little torque could cause the bolt to work its way loose, and too much could cause uneven pressure and it could even cause the head of the bolt to snap off.

Instructions

    1

    Grip the metal portion of the Truecraft torque wrench with one hand and grip the handle of the torque wrench with the other.

    2

    Turn the black handle on the torque wrench until it matches up with the specified torque you need to obtain. For example, if your bolt requires 20 foot-pounds of torque, turn the handle until the end of the handle lines up with the line next to 20.

    3

    Push the socket onto the head of the Truecraft torque wrench and then place the socket onto the head of the bolt.

    4

    Tighten the bolt down with the torque wrench with slow smooth strokes. Continue this until the torque wrench clicks one time. You have reached the desired torque on the bolt.

    5

    If you tighten past the first click you will over-torque the bolt. This could cause the bolt to break.

ReadMore

Tuesday, November 26, 2013

How to Use a Bicycle Pump to Fill an Air Tank

How to Use a Bicycle Pump to Fill an Air Tank

Compressed air is useful for many things. It can pump up flat tires, run a variety of air tools, or simply be used to clean a bit of dirt out of a crevice. In order to create and use compressed air you need to have a commercial air compressor or an air tank. If you have an air-tank equipped with a pressure gauge and Schrader valve you can easily fill it up with a bike pump.

Instructions

    1

    Press the bike pump connection onto the Schrader valve located near the top of the air tank. It will be an approximately 3/8 inch metal threaded tube with a small pin in the center.

    2

    Pump up the tank while keeping an eye on the tank air valve. After several dozen pumps you should start to see some air pressure registered. Continue this action until the tank reads about 20 pounds of pressure.

    3

    Remove the bike pump nozzle and use the tire gauge to verify the pressure for safety. Once it is verified, continue pumping to your desired pressure.

ReadMore

Friday, November 22, 2013

What Weight Engine Oil Does a VW VR6 Use

Replacing the engine oil in your Volkswagen VR6 with the appropriate engine oil weight is important to maintain proper engine function. The type of oil you use depends on the weather. Oil that functions well in southern Texas may not be appropriate for winters in New England. By taking into account the temperature and information from your owners manual, you can determine the best oil to use in your car.

Temperature Considerations

    Temperature should be a primary consideration when choosing engine oil. If you are going to operate your car at temperatures below 15 degrees Fahrenheit, choose an engine oil with a first weight of 10 or lower (e.g. 10W30, 10W40). If you are going to operate your engine above 100 degrees Fahrenheit, use an engine oil in which the second number is at least 50 (e.g. 10W50, 20W50).

Manufacturer Recommendations

    VW recommends engine oil meeting Volkswagens "502.00" engine oil standard. Many oils meet the quality standards for Volkswagens 502.00 standard.

Approved Oils

    Before purchasing oil, check the bottle or manufacturers website to make sure the oil conforms to Volkswagens standard. If you have any questions, contact your local Volkswagen dealer.

ReadMore

Wednesday, November 20, 2013

How to Use a Bore Scope for Auto Lockouts

How to Use a Bore Scope for Auto Lockouts

Bore scopes are optical devices comprised of a length of fiber-optic cabling fed into a display screen or lens, allowing the user to feed the thin end of the fiber-optic cable into a difficult-to-reach, tight area, and project the image onto the screen of the device. These devices can be extremely convenient when attempting to open a locked car door. With the scope inserted into the crevice between the car door and window, you can easily identify the lock control components, making opening a locked door a simple task.

Instructions

    1

    Insert a plastic wedge -- available at a home-improvement store -- between the car window and door, creating a gap between them and allowing you to insert your bore scope into the door cavity.

    2

    Insert your bore, or fiber, scope and while looking at the display or through the lens, identify the lock control rod. This will be a rod that connects the internal lock control with the key control mounted on the rear of the keyed door lock cylinder in the car door.

    3

    Insert the Slim Jim unlocking device or wire coat hanger with a bend at the tip. While looking through the bore scope, place the Slim Jim or wire coat hanger hook over the lock control rod and either push down, pull up, or push it sideways to toggle it into the open position.

    4

    Remove the Slim Jim or coat hanger, bore scope and plastic wedge, and open the unlocked car door.

ReadMore

Sunday, November 17, 2013

Why Use an Auto Repair Chain

Why Use an Auto Repair Chain?

When routine maintenance is needed or when car problems arise, three main options are available. The car can be taken to the dealership, an auto repair chain shop or an independent repair shop. Auto repair chain shops offer certain advantages over the other two options.

Reduced Cost

    Auto chain shops in general offer lower prices for routine maintenance, such as oil changes, explained AutoMD President Shane Evangelist. Auto repair chains often offer specials or promotions for oil changes and other basic services. Because an auto repair chain has less overhead and lower labor pricing, it can afford to offer lower prices to its customers. Also, an auto repair chain generally uses aftermarket high-quality auto parts instead of dealership factory parts. Auto repair chains often publish coupons in flyers or over the Internet that offer additional discounts.

Reputation

    Because they have a reputation to uphold, auto chain shops strive to provide quality service on the first visit. According to one auto repair chain, Cottman Transmission & Total Care, many auto chain facilities are registered with the BBB (Better Business Bureau) and many technicians are listed with the AAA-approved auto repair list. Like dealerships, most auto repair chains honor extended warranties on vehicles.

Various Locations

    Because an auto repair chain has stores in several areas, the repair history of the vehicle will be saved in the chains computer system. This is convenient for customers who have moved to a new location or for those who for some reason need their vehicles fixed while out of town. Also, since a number of shops form part of the auto repair chain, more company resources can be shared for fixing car problems.

Knowledgeable Technicians

    As many chains specialize in a certain aspects of auto repair, their technicians gain experience and efficiency in these specific fields. Unlike a dealership, they have knowledge of many different types of cars, not just one make or model. That being so, they can offer service for all the cars that a family owns. Dealerships also have to focus on selling cars, but auto repair chains are devoted exclusively to performing auto repair and maintenance.

ReadMore

Friday, September 20, 2013

How to Use a Power Steering Pulley Puller

How to Use a Power Steering Pulley Puller

Power steering pulleys are usually fitted on the pump shaft by pressing and the assembly is held together with friction. Hence, if you wish to remove the power steering pulley, it cannot be done by hand. The specific tool to be used is a puller that can remove the pulley from the pump shaft. This puller is different from the usual gear pullers with jaws. Various brands of the puller are available; there may be slight differences in the parts, but they function in a similar manner. A few brands also come with tools that can be used to fit back the power steering pulley.

Instructions

    1

    Study the parts. A power steering pulley puller consists of two half-parts that make up a split collar, a metal sleeve to retain the collar and a threaded bolt which is the puller. If your kit consists of tools to re-install the pulley, therell be a bolt nut assembly, too.

    2

    Fit on the puller by inserting the half-part that projects more inward below the pulley lip. Close the two parts so the pump shaft is held tight. Fit the metal sleeve over the ring formed by closing the two parts. Push the rounded end of the threaded bolt inside the pump shaft, until it touches the pulley shaft, and tighten it.

    3

    Position a wrench at the bottom of the threaded puller assembly. On the top side, near the threaded shaft, use a ratchet. Tighten the nut and bolt parts by screwing the puller assembly into the bottom portion; this will cause the pulley to move off the pump shaft.

    4

    Fit back the pulley by positioning it to sit squarely on the pump shaft. Use the bolt nut assembly provided with the puller kit. Insert the bolt inside the pump shafts internal threading and screw it on until the bolt touches the lower surface. Push the pulley on by rotating the nut assembly along the bolt. When the pulley has reached down completely, the nut assembly stops moving; remove the assembly and check that the pulley is flush with the level of the pump shaft.

ReadMore