Pages

Showing posts with label s. Show all posts
Showing posts with label s. Show all posts

Saturday, March 8, 2014

How to Install a Fuel Pump in a 1984 GMC S 15

The 1984 GMC S-15 truck with the six-cylinder, 2.8-liter engine is carbureted instead of fuel-injected. As such, the fuel pump on this truck is mounted on the side of the engine block and driven by a cam on the camshaft. If the fuel pump isnt working properly, you can experience poor performance, stalling, and even backfiring. You can change the fuel pump n the 1984 S-15 in about an hour to two hours in your front yard.

Instructions

    1

    Slide the jack under the front frame cross member, and lift the truck until there is enough room for you to comfortably slide under.

    2

    Place the jack stands under the frame behind both front wheels, and caully lower the truck onto them. Remove the jack.

    3

    Slide under the truck, and locate the pump on the lower left front side of the engine. Tag the fuel lines if they are both threaded fittings so you know which line goes where.

    4

    Remove the fuel lines from the pump. Most fuel pumps will have two threaded fittings; remove these using the flare nut wrenches and turning the fittings counterclockwise. If either of the connections has a rubber hose clamped to it, squeeze the clamp with the pliers, and slide it back on the hose a few inches. Grasp the fuel line, and twist and pull it off the pump nipple.

    5

    Remove the bolts securing the fuel pump to the block by turning them counterclockwise with the ratchet and socket. Remove the fuel pump by pulling it away from the engine.

    6

    Clean the block side mating surface of all remnants of the old gasket using the gasket scraper.

    7

    Apply a thin bead of RTV sealant to both the block and pump mating surfaces. Apply the gasket to block mating surface.

    8

    Hold the new fuel pump in place, and insert the bolts in the bolt holes, and turn them clockwise by hand. Tighten these bolts to 15 foot-pounds with the ratchet and socket.

    9

    Reattach the fuel lines to the pump. For threaded fittings, thread the fittings into the new pump by turning them clockwise by hand. Tighten the fittings to 15 foot-pounds using the flare nut wrench. If so equipped, slip the rubber fuel line over the nipple. Squeeze the clamp, and slide it over the nipple.

    10

    Slide the jack back under the front cross member, and lift the truck off the jack stands. Remove the jack stands, and lower the truck. Start the truck, and verify there are no leaks.

ReadMore

Thursday, December 12, 2013

Chevy S 10 Pickup Tailgate Problems

Some Chevy S-10 pickup trucks have problems with the tailgates. The tailgate cables ensure the tailgate stays at the correct level when it is in the down position. Weak cables may result in personal injury and damage to the truck.

History

    The National Highway Traffic Safety Administration completed a defect investigation (EA05008) which details that owners of select Chevy S-10 trucks are authorized to have the cables replaced free of charge. The investigation also recommended that owners of Chevy S-10 trucks periodically inspect the cables for signs of wear and tear.

Warning

    Cables that are worn or frayed can break unexpectedly. Moisture interacting with the cable reduces the strength of the cable. When the cable breaks, the tailgate can come down and hit the bumper. This can damage the bumper and tailgate cosmetically. A person may be injured if he is near or on the tailgate when the cable breaks.

Recommendation

    Cables that appear to be worn, frayed or bulging should be brought to the attention of General Motors. A trained technician will be able to determine if the cables need to be replaced. Cables may be replaced free of charge if they are included in a warranty, safety notice or recall.

ReadMore

Thursday, November 14, 2013

How to Remove the Door Handles From a Chevy S 10

A properly working door handle makes for an important part of your Chevy S-10 if you do not want to get into your truck like a "Dukes of Hazzard" television star. The metal used to manufacturer the brackets on the door handle, known as "pop steel," is a relatively soft metal usually used on low-wear items. Over time, however, the brackets can become weak and eventually break.

Instructions

    1

    Open the door, and remove the screws that secure the inner door panel to the sheet metal on the inner door with a screwdriver.

    2

    Pull on the upper left corner of the door to loosen the door panel from the sheet metal. Small plastic tabs connect the door panel with the sheet metal about every 10 inches. As you pull on the panel, pull the tabs out of the sheet metal.

    3

    Locate the back of the door handle by looking through the upper holes in the sheet metal. On the left side of the door handle, youll see a long bar connected to a piece of metal on the side of the handle. The bar moves when you lift up on the handle and opens the door latch.

    4

    Remove the metal bar from the left side of the handle by pulling the bar to the left. (The bar is not attached with bolts.)

    5

    Lift up on the handle from the outside door, and remove the two bolts located under the handle with wrenches. The bolts secure the handle to the sheet metal on the outside of the door.

    6

    Pull the handle out of the door.

ReadMore