Pages

Showing posts with label is. Show all posts
Showing posts with label is. Show all posts

Saturday, May 17, 2014

What Is the Benefit of a Transmission Service

What Is the Benefit of a Transmission Service?

Ask any mechanic and youll be assured that having your transmission serviced on a regular basis is a smart move and will extend its life. Service can range from a basic service check to a pressurized flush. Aside from the fact that a flush replaces the old fluid in your transmission with new fluid, this procedure also cleans the filter and system; in addition, it can identify minor transmission issues before they become major problems.

General Benefits

    A general transmission service involves removing the fluid pan, replacing the filter and gasket, and replacing some of the transmission fluid. According to Speed Lube, this routine service extends the life of the transmission. Clean lubricant prevents seals and gaskets from hardening, which can cause metal parts to warp and valves to stick.

Full Transmission Flush Benefits

    A flush replaces all of the vehicles transmission fluid. Pressure is used to push all of the old fluid out so that it can be replaced with new fluid. Flushing also does a good job of cleaning out a transmissions internal parts and its filter.

Discovering Transmission Issues

    Both general service and a flush can reveal transmission problems but a flush will give a more accurate indication of what is going on inside your transmission. This is because the pressurized cleaning method helps expose decaying seals and cracks. It will be less costly to replace an old seal or gasket than to wait for serious damage to occur and then have to replace the complete transmission.

ReadMore

Sunday, May 11, 2014

Why Is a Drive Shaft Hollow

Why Is a Drive Shaft Hollow?

The drive shaft is a long rod or tube used to carry rotational force from a vehicles engine to the wheels. Drive shafts vary in size, configuration and features. One variation is a hollow drive shaft, used for several reasons.

Rotational Inertia

    The engine would have to power the rotation of a solid piece of metal. With a hollow drive shaft, there is less mass for the engine to push and the force it produces is able to accelerate the drive train faster.

Low Cost

    Making a hollow drive shaft uses less material than a solid one. With some good engineering, manufacturers can make hollow drive shafts with the same structural integrity as their solid counterparts. The saved material lowers the cost.

Fuel Efficiency

    Because of the reduced rotational inertia, the engine can get the same push with less work. This translates into fuel efficiency. With less material to push, it takes less fuel to get the same acceleration.

ReadMore

Wednesday, April 30, 2014

Can You Pull off Spark Plug Wires While the Engine Is Running

Like most ponderings in automotive repair, the question of removing spark plug wires from a running engine isnt necessarily so much one of "could" as it is of "should." Technically, yes, you can yank the plug wires off of a running engine just as easily as you could one that isnt running, but it may not necessarily prove conducive to you or your cars good health.

You Could

    Removing a plug wire from a running engine isnt likely to result in catastrophic engine failure, particularly if you put it back on shortly afterward. All spark plugs misfire from time to time, you just dont notice it because its intermittent, random and usually happens so quickly that the cylinders firing again before the engine has a chance to vibrate. So, intentionally creating a misfire by removing the plug wire for a few seconds or even a few minutes isnt likely to destroy anything on most engines.

Common Effects on the Engine

    Most engines have a rubber ring on the front of the crankshaft called a harmonic balancer; on the outer edge of the balancer is a heavy, metal ring. When the explosions in the engines cylinders push down on the pistons, the forces they exert quickly accelerate the crankshaft. When that accelerations over, the crank tries to slow down, resulting in a constant cycle of acceleration and deceleration that manifests as vibration in the crankshaft. The metal ring on the balancer resists these sudden, but tiny, vibrations and keep the crank from tearing itself in two. Over a long enough period of time, a dead cylinder and the resultant heavy vibration will over-work the balancer, causing it to fail. Once that happens, you could be looking at serious damage to the engine.

Effects on the Converter

    Your cars catalytic converter works something like a blast furnace to convert toxic gases produced by your engine into more inert forms that wont drown polar bears or grow fish with three eyes. The converter takes advantage of unburned fuel -- which is, itself, a pollutant -- coming from your engine and uses it to fuel the furnace in the converter matrix. More fuel means more heat. Killing the spark in one cylinder will drastically increase the amount of fuel pouring into your exhaust, which will, at some point, cause the converter to overheat and fail. The engines control computer will compensate for this to some extent, but you can count on extra fuel going into the exhaust.

Lean-Out

    Depending upon the computers control strategy, disconnecting a plug wire and leaving it that way could seriously fry something. When the oxygen sensor detects excess fuel in the exhaust, your cars computer may assume that this represents a net excess of fuel through all the cylinders. It will respond by decreasing the amount of fuel injected to all of the other cylinders in order to get the air/fuel ratio back in line. The resulting lean condition will increase combustion chamber temperature, causing overheating, detonation in the engine and, eventually, complete meltdown. Most computers do have programming provisions to account for a dead cylinder, and wont react this way; but some dont, and theres no way to be sure unless you know exactly how your fuel injection system thinks.

Safety Issues

    Before pulling the plug wire off of a running engine, bear in mind that your are, in fact, grabbing a live wire with about 40,000 volts worth of electricity coursing through it. Normally, this electricity will pass through the plug wire and race to the spark plug, which acts as a ground. But when you remove that ground, the spark is going to find the next, most convenient ground. If you happen to be touching the body of the car when you pull the wire off, then you become that ground. While electricity normally wouldnt arc through the insulation, even if it is a bit old and damaged, removing the primary ground will make that spark pretty determined to get out whatever way it can. Its not likely to kill you unless you have heart or nervous system problems, since the amperage is very low -- but the sensation is rather, shall we say, "life affirming."

ReadMore

Tuesday, April 29, 2014

How to Tell If Your Fuel Pump Is Broken

How to Tell If Your Fuel Pump Is Broken?

The fuel pump is an essential component of a vehicle. Fuel is pumped from the fuel tank to the engine. Without a functioning fuel pump, adequate fuel pressure cannot be delivered to the engine. This will cause problems such as hard starting, rough idle, misfiring, hesitation and stalling and can even prevent the car from starting . This may happen at the most inconvenient time. If you suspect that your fuel pump is broken, there are certain tests that you can perform to confirm it.

Instructions

    1

    Listen for a humming sound that normally occurs when the key is turned to the "Start" position. Turn the key in the ignition to the "Start" position and listen for a humming sound from the fuel tank. A hum means that the pump is in working condition.

    2

    Check if your fuel pump is broken by doing a static fuel test. Turn the key in the ignition to the "on" position. Look at the fuel pressure gauge to detect movements. The fuel pressure should immediately come up and stay steady. If it doesnt, that can indicate that there is a defect in the fuel pump.

    3

    Connect a voltage meter to the wires that connect to your fuel pump. Connect the voltage meter to the green wire. The fuel pump wires are located under the vehicle, behind the drivers door. Let someone start the engine while the voltage meter is connected to the wire. A normal reading is between 10 to 11 volts. If there is a zero reading, this usually mean that the fuel pump is bad.

ReadMore

Saturday, April 19, 2014

What Happens When Water Is Put Into a Cars Gas Tank

What Happens When Water Is Put Into a Cars Gas Tank?

Water and fuel dont mix, so its never a good idea to put water into a cars gas tank. However, when water does get into a gas tank, either accidentally, or as the result of a malicious prank, the result is engine trouble.

Condensation

    Water can get into a gas tank even if you didnt put it there. Sometimes water gets in through a badly sealed cap on the tank, or by natural condensation on the inside of the gas tank

Problems

    Water in the gas tank may lead to the car bucking, stalling or not starting at all, or starting the car could be difficult. This is because the water and fuel separate, especially when the car has been sitting for a while, and the water sinks to the bottom with the fuel on top. Water can also get into other parts of the engine causing rust and corrosion.

Removal

    The method you use to get rid of water in your cars gas tank depends on how much got in there in the first place. In the case of only a little water, an additive that dries up water could be used. The additive combines with the water as it goes through the running engine. If there is a lot of water, a mechanic will have to remove the gas. This may include removing the fuel tank from the car and putting in new filters. The tank is then put back and is filled with clean gas.

ReadMore

Thursday, April 3, 2014

My Power Steering Oil Is Leaking

When a car is leaking power steering fluid, the leak needs to be found and repaired in order to keep the system working properly. Power steering fluid leaks can allow moisture and other contaminants into the system, which can cause further damage.

Leaking Seals

    One of the most common sources of leaks in a power steering system is old seals that have dried out and shrunk. Power steering stop leak additives are designed to soften and swell older seals, causing them to seal the leak. These additives are inexpensive and easy to use to correct minor leaks.

Lines and Hoses

    Power steering lines and hoses carry pressurized power steering fluid from the power steering pump to the steering rack. The lines and hoses can become damaged and cause a leak. Car owners should inspect these caully looking for splits, cracks, and kinks. Lines or hoses that are leaking should be replaced.

Worn Parts

    The power steering pump and other parts of the power steering system can become worn or damaged and cause leaks. To identify the leak, wipe clean the power steering system, then observe it while a helper starts the motor and turns the wheels. These leaks will require the replacement of the defective part.

ReadMore

Sunday, March 23, 2014

What Is a Distributor Pickup Coil

What Is a Distributor Pickup Coil?

The ignition system in your car takes the spark generated by the distributor pickup coil and sends it through the plug wires to the spark plugs at just the right time. With this in mind, the pickup coil is a vital part of the ignition system.

Definition

    The distributor shaft is typically turned by a gear on the bottom of the shaft. This gear is turned either by a timing belt, a timing chain or directly by the camshaft. The pickup coil is around this shaft, generally under the distributor rotor. The pickup coil is an electromagnetic sensor.

Function

    On the distributor shaft there is a raised metal "tongue." This tongue passes by the pickup coil each time the distributor rotates. This causes the pickup coil to send a signal to the ignition control module, letting it know where the distributor is in its rotation. This corresponds with where the motor is in the compression cycle. The control module then knows when to send spark to the coil.

Options

    Modern vehicles usually have a camshaft position sensor or a crankshaft position sensor and sometimes both. These work on the same principle as the pickup coil; but because they are located directly beside the crankshaft and the camshaft, they are more accurate. In newer vehicles these sensors also help time fuel delivery through the injection system, making them more efficient.

ReadMore

Saturday, March 1, 2014

Why Is the Boron Additive in Engine Oil

A boron-based additive makes motor oil more slippery, according to the Argonne National Laboratory. Boric acid particles can reduce friction between engine parts in an automobile and thus reduce metal wear.

History

    In 1991, scientist Ali Erdemir discovered that boric acid could make surfaces slicker than Teflon. He also found that reducing the boric acid to nanoparticles enhanced this quality by staying in suspension in motor oil rather than separating.

Fuel Savings

    Reducing friction reduces the amount of energy lost as heat and results in up to a 5 percent decrease in fuel consumption. Furthermore, boric acid is cheap to make and is neither a hazardous or toxic material.

Further Developments

    Some commercial motor oils with boron-derived nanoparticles are available. Erdemir expects such particles will have wider applications in other industries, including medicine, aviation and air conditioning.

ReadMore

Sunday, January 26, 2014

What Is an EGT Sensor on a WRX

An exhaust gas temperature (EGT) sensor is a device used to measure a car engines air-fuel ratio. It often is used on high-performance vehicles, particularly those that have turbocharged engines.

Purpose

    The EGT sensor monitors the temperature of the exhaust system of certain internal combustion engines, specifically those that are turbocharged for high performance, like the Subaru WRX.

Placement

    The EGT sensor can be placed before the turbo, where it measures the temperature of air as it enters the turbine, or after the turbo, where it measures the temperature of the exhaust.

Importance

    High engine temperatures in an engines combustion chamber can cause detonation, resulted in melted valves and pistons, and generally destroying the engine. The EGT sensor can warn the operator of dangerously high temperatures, thus preventing fatal engine malfunction.

ReadMore

Thursday, January 23, 2014

What Is a Smog Pump

What Is a Smog Pump?

A smog pump is a crucial piece of equipment used for helping to reduce emissions. It is one of the systems found in automobiles that helps fuel burn cleaner.

Air Injection

    The smog pump is the common term for the secondary air injection system (or just air injection system). After combustion occurs, the exhaust gases must leave the combustion chamber through a port. The air injection system pumps fresh oxygen into the exhaust port, causing the exhaust gases (hydrocarbon and carbon monoxide) to continue to burn and theore deplete more efficiently. On some vehicles, it also supplies air to the catalytic converter. The system usually consists of an air pump, a diverter valve, an air distributor and a check valve.

Air Pump

    The air pump is what creates the force of the air to push fresh air into the system. It is run by a belt or electric motor.

Diverter Valve

    The diverter valve is used by some cars to keep too much air from entering the system when the vehicle is decelerating, reducing backfiring and limiting air pressure.

Air Distributor

    The air distributor is known as the air management valve or air distribution manifold. This valve switches the flow of air direction to point toward either the exhaust manifold or toward the catalytic converter, depending on the operating conditions of the vehicle.

Check Valves

    Check valves prevent exhaust air from flowing into the system and causing possible damage.

ReadMore

Tuesday, January 14, 2014

What Is Thread Coating Liquid

According to Precote.com, liquid thread coating is the application of a sealant, lubricant or anti-corrosion chemical to the threads of screws, nuts and bolts. Liquid thread coatings are used by automotive manufacturers, the airline industry, railway companies, shipyards and nearly every manufacturing industry. Liquid thread coatings can be applied during the manufacturing process or after-market to the threads of screws, nuts and bolts.

Liquid Nylon

    Liquid nylon provides a number of benefits when applied to part threads and works well on both iron and non-iron metal threads, such as steel, aluminum, brass and stainless steel threads. A thin layer of liquid nylon protects threads from wear, friction and corrosive elements and inhibits electrical conductivity. The nylon remains intact in both high heat and freezing temperatures.

Wax

    Wax-based liquid thread coatings serve primarily as a thread lubricant. Wax-based liquid coatings are applied to nut, bolt and screw threads to make assembly smoother and to avoid cross-threading or sticking threads. The liquid wax is sprayed on the part or the part is dipped in the wax by a machine, or the wax can be applied by hand. New threaded parts may be coated with liquid wax lubricant at the end of the manufacturing process.

Teflon

    Liquid Teflon is often applied to threaded parts as a sealant and to help reduce wear caused by friction. Liquid Teflon is typically used on screws, nuts and bolts that are subjected to vibration, such as those used in refrigeration units and manufacturing environments. Liquid Teflon thread lubrication applications may contain other chemicals, such as polytetrafluoroethylene that increase the efficiency of Teflon lubrication. Teflon is used on metal, plastic and fiberglass parts.

Fluoro-Carbon Coating

    Liquid fluoro-carbon thread coatings prevent threads from damage during assembly of parts by lubricating the threads. Fluoro-carbon thread coating is often used on part threads if the final product will be painted before or after assembly. Once dry, the fluoro-carbon coating resists paint. Fluoro-carbon coatings also resist electroplated paints and primers.

ReadMore

Thursday, December 12, 2013

Where Is the Oil Sending Unit on a 2004 350Z

The oil sending unit on a Nissan 350Z coupe is an integral part of the engines lubrication system. This unit is attached to the front-right side of the engine block, just below the alternator. The oil filter, oil pan, and lower engine compartment are protected by a special undercover thats attached to the frame with metric steel bolts. The vehicle must be lifted, and the cover must be removed in order to access the oil filter and oil sending unit.

Instructions

    1

    Shut off the engine, chock the rear wheels, and apply the parking brake.

    2

    Lift the front of the vehicle with a jack and support it with two jack stands; one under each side of the front frame. Check to make sure that the stands are firmly supporting the vehicle.

    3

    Slide under the vehicle on a mechanics creeper and remove the bolts holding the engine undercover to the frame with a metric socket and a ratchet.

    4

    Shine a work light up on the right side of the engine block, just below the alternator. The oil filter is attached to the oil sending unit.

ReadMore

Saturday, December 7, 2013

What Weight of Oil Is Best for a Four Cylinder Car During the Winter

What Weight of Oil Is Best for a Four Cylinder Car During the Winter?

The location of the vehicle in winter will affect the type of oil chosen during colder months. Hawaii, for example, stays relatively warm all year and therefore there is less need to change oil weight with the season. Consulting the owners manual for the specific vehicle will reveal what the manufacturer recommends (for instance, the owners manual for a 2001 Honda Civic recommends using 5W-20 oil year-round, but 5W-30 is acceptable if 5W-20 is not available).

Numbers and Letters on Oil

    The numbers on motor oil show the oils viscosity rating and range from zero to 50. The oils weight is the "viscosity index" on a scale up to 100 degrees Celsius. The lower number, often followed by a W for "winter", corresponds to the oils ease of movement during colder temperatures. The higher numbers correspond the the oils thickness and ability to maintain that thickness even at higher temperatures. Numbers such as 5W-30 have a wide range, from below -30 degrees to over 100 degrees.

Age of the Vehicle

    Older vehicles, whose engines have high mileage, are often recommended to use or switch to an oil that is thicker. This will help limit the noise produced by older engines, as well as reducing the overall oil-consumption by the vehicle and prolong its life. The improved lubrication of the engine helps protect it from wear due to long-time use and age.

Regional Differences

    Many newer vehicles, less than 20 years old for example, are recommended by manufacturers to use one type of oil year-round, such as the 5W-20 in a 2001 Honda Civic. If the location, however, suffers extremely cold winters (temperatures below -30 degrees Celsius, for instance) local auto parts stores and mechanics will have regionally-appropriate recommendations for oil weights. Not all manufacturers will account for such temperature extremes in the owners manuals so consulting local experts will prove helpful.

ReadMore

Friday, November 22, 2013

Where Is the Fuse Box for a 2005 Ford Escape

Where Is the Fuse Box for a 2005 Ford Escape?

The 2005 Ford Escape is a compact four door SUV that first came out in 2001. It has two fuse panels: the main panel and an additional power distribution box to house high current fuses. The fuses help to run electronic equipment like the lights, radio and power doors and windows.

Main Fuse Panel

    The main fuse box for the 2005 Ford Escape is on the passenger side of the center console near the instrument panel below the glove compartment. Remove the panel cover so you can access the fuses.

Power Distribution Box

    The power distribution box, which holds the high current fuses, is in the engine compartment on the right hand side. The high-current fuses keep the electrical systems from overloading.

Safety

    To safely replace fuses, make sure your cars engine and power are off. When replacing high current fuses, disconnect the battery before opening the panel to the power distribution box. Use the list of fuse codes in your owners manual, and the fuse puller tool in the main fuse panel to remove and replace fuses. Always replace the panel to the power distribution box before reconnecting the battery.

ReadMore

Thursday, November 21, 2013

What Is the Difference Between a Front Pipe a Header Pipe

The exhaust pipes on your car, truck or motorcycle carry the gasses expelled from the engine during the combustion process safely to the rear of the vehicle. This is usually accomplished with pieces of steel tubing that are suspended to the underside of the vehicle. Since the exhaust usually has to wind over, under or around the vehicle undercarriage to get to the rearmost part of the vehicle, it is manufactured in several different pieces and either welded, bolted or clamped together to form a continuous flow. Each manufacturer may have different names for the various exhaust pieces, but may include the header pipe, front pipe, exhaust pipe, catalytic converter, muffler, resonator and tailpipe.

Exhaust Manifold

    Converting the exhaust from each cylinder on your engine to a single outlet is usually accomplished with an exhaust manifold. An exhaust manifold is usually constructed of cast iron and is bolted to the cylinder head. V-type or boxer engines have two banks of cylinders -- one on each side of the block. In these cases, there should be an exhaust manifold bolted to each cylinder head. The exhaust manifold is usually not considered part of the exhaust system, but it gives the exhaust pipe a place to attach to.

Header Pipe

    When referring to exhaust pipes, the header pipe sometimes refers to the part of the exhaust system that attaches directly to the exhaust manifold of the engine. If your vehicle is a single cylinder motorcycle or a vehicle that has an inline engine, a single header pipe would connect directly to the exhaust manifold or engine. Header pipes used on V-type or boxer engines can sometimes be referred to as a Y pipe, as it connects to both sides of the engine and comes together to form one pipe. Some vehicles use a dual exhaust system. These types of vehicles may a have a separate, single header pipe for each exhaust header.

Headers

    Some vehicles may use factory or aftermarket exhaust headers in place of a cast iron exhaust manifold and header pipe. Headers are usually constructed of several pipes welded together and take the place of both the exhaust manifold and the header pipe. Headers are usually tuned, meaning the length of the tube that attaches to each exhaust port on the engine is engineered in such a way to extract maximum power and efficiency from the engine. Headers are factory-installed on some performance engines, but are usually an aftermarket accessory that is owner-installed.

Front Pipe

    Depending on the manufacturer, the front pipe on an exhaust system can refer to pipe that bolts to the engine -- the header pipe -- or the pipe that connects the header pipe to the remainder of the exhaust system. The exhaust system on vehicles that have transverse-mounted engines may need to compensate for the back-and-forth rocking motion of the engine when accelerating or decelerating. Whereas the header pipe may be a solid, fixed pipe, a flexible pipe -- sometimes referred to as the front pipe -- connects the header pipe to the rear of the exhaust system. On some vehicles, the exhaust pipe that connects to the rear of the flexible pipe may be referred to as the front pipe.

ReadMore

Tuesday, November 12, 2013

What Is an AX15 Transmission

The AX15 is a five-speed, standard shift transmission made by Aisin-Warner. Although the transmission is no longer used in newer vehicles, Aisin-Warner still produces the part.

Vehicle Models

    Jeep used the AX15 in its 1988 Wrangler XJ and YJ models, the Comanche and the MJ Cherokee. The transmission was standard in all XJ, YJ and TJ Jeeps from 1988 to 1999. In 1993, the AX15 came in the ZJ Grand Cherokee in the six-cylinder model.

Description

    The AX15 has a cast aluminum case and mid-plate. It measures 16.5 inches in length. It is a top-shifting, overdrive transmission with a split case. All gears are synchronized and helically cut. The gear ratios are 3.83 for first, 2.33 for second, 1.44 for third, 1.00 for fourth and 0.79 for fifth. The AX15 uses a 10-spline input shaft. It has a 23-spline output shaft and uses dowel pins for bellhousing alignment.

Variations

    The input shaft pilot tips were smaller in the AX15 made from 1988 to 1991. They measured 19/32 inch, while later models use a 3/4-inch tip. The 1988 to 1993 models had an internal slave throwout, which was switched to a slave cylinder with cross arm design in later years.

ReadMore

Friday, November 8, 2013

What Is Etching Primer Used For

What Is Etching Primer Used For?

Etching primer has many different uses in a variety of industries, such as automotive, construction and medical. Etching primer is made with different ingredients that etch and bond to surfaces, including various metals. Though it can be used on different materials, including fiberglass and wood, etching primer is more commonly used for preparing metal surfaces to be finished with paint. Etching primer is also referred to as self-etching primer.

Automotive and Boating

    Etching primer is used to seal both automobiles and boats, protecting the metal bodies from the elements of weather, salt water, wear and tear and other damaging effects of wind and water. When used properly, it can help prevent rust and cracking in the metal and surface when finished. An etching primer can be used to seal and protect wood, fiberglass, aluminum, iron or other metals used in cars and boats.

Adhesive

    The properties of an etching primer allow it to be used to help make different metal surfaces stick together. For example, the primer can prepare the surface of two metal parts prior to adhesive application. The primer allows the adhesive to create a stronger bond on the surface of both pieces. The etching primer can also be used to seal and adhere protective coatings to surfaces.

Protection and Preparation

    Although etching primer is primarily used to prepare surfaces for painting and installation, it also protects metal surfaces from corrosion, rust and damage from exposure to various elements. Once the etching primer has dried the surface can be sanded and painted while still preventing corrosion.

Dental

    Through research, it has been discovered that etching primer can be used to protect and prime teeth. The etching primer is used in the dental field to bond teeth and cover with sealants. The primer is also used by orthodontists when adhering braces to the teeth.

ReadMore

Friday, November 1, 2013

What Is a Carriage Bolt Assembly

What Is a Carriage Bolt Assembly?

Carriage bolt assemblies are threaded fasteners with a bolt that has a rounded, dome-shaped head. The bolt has a square neck that extends from the head towards the threads. A regular hex nut or wing nut allows the assembly to hold the components together. This assembly can be tightened with just one wrench.

Function

    When used in metalworking applications, carriage bolts are often called plow bolts. These bolts must go through a square opening to accommodate the neck, which will keep the bolt from turning when the assemblys nut is tightened.

Considerations

    Carriage bolt assemblies are commonly used in carpentry and construction; they are well-suited for fastening two structural wood pieces together, especially when extra strength is required. The square neck sinks into the wood as the fastener is tightened, preventing the bolt from turning and countersinking the bolt head at the same time.

Types

    Carriage bolt assemblies are available in varying degrees of hardness, or grades. Grades three, five and eight are common strengths. Zinc is the most common coating for a carriage bolt. They are also available in silicon bronze.

ReadMore

Saturday, October 26, 2013

What Is an Engine Mount Strut Bracket

What Is an Engine Mount Strut Bracket?

An engine mount strut bracket consists of several separate parts and components. Struts and mounts are the main components that make up the engine mount strut bracket. These parts help the engine run properly by connecting all components of the engine together so the parts can run in unison with one another.

Mount

    The mount is usually made of steel or rubber. It is a connector piece for other components of the engine. According to the glossary on AutoZone.com, engine mounts include "pulleys, mounting plates, belts, and fittings necessary to mount a compressor."

Strut

    The strut is the part of the engine that helps resist compression and in return helps strengthen the frame of the engine. According to the Glossary on AutoZone.com, struts "maintain the knuckle position and act as shock absorbers to control spring action in a vehicles suspension system." Struts that have failed or stopped working may cause the car to bounce around or shake while driving.

Safety

    Consistent checkups on engine mounts and strut brackets can help minimize engine issues. Broken mounts can lead to leaks and punctures of the engine. Broken struts will keep your car from absorbing compressions, leading to flat tires.

ReadMore

Sunday, October 20, 2013

What Is a Heat Crossover

What Is a Heat Crossover?

An internal combustion engine produces plenty of heat. While this heat is a potentially destructive factor, the heat crossover puts some of it to good use.

Exhaust Manifolds

    Gasoline burns in structures called cylinders, usually six or eight in number. Half of the cylinders lie on the left side of the engine, the other half on the right. Little exhaust pipes lead from each cylinder to the main exhaust system. Collectively these pipes are called the exhaust manifold. Some cars have two exhaust manifolds, one on each side of the engine. The right exhaust manifold collects exhaust gases from the cylinders on the right side of the engine while the left exhaust manifold collects exhaust gases from the cylinders on the left.

Fuel Delivery System

    The carburetor lies in the center of the engine between the two sets of cylinders. The carburetor mixes the fuel with air and sends the mixture to the two sets of cylinders through a delivery system that includes a chamber called the plenum and an intake manifold consisting of pipes to each cylinder.

Heat Crossover

    Some car engines have an extra passage in the intake manifold called a heat crossover. It leads from the exhaust manifold on one side of the engine to the exhaust manifold on the other side, passing the carburetor and the plenum en route. Some of the hot exhaust gases pass through this heat crossover before exiting through the exhaust system. As these gases pass by, the heat of the exhaust gas warms the carburetor and plenum. Consequently, the injected fuel vaporizes better. This is especially helpful when the car first starts and the engine is still cold..

ReadMore