Pages

Showing posts with label 2005. Show all posts
Showing posts with label 2005. Show all posts

Sunday, March 30, 2014

How Do I Change the Alternator Belt on a 2005 Kia Spectra

How Do I Change the Alternator Belt on a 2005 Kia Spectra?

The 2005 Kia Spectra left the factory with a 2.0-liter, four-cylinder engine with a single serpentine belt driving the alternator and water pump from power supplied by the crankshaft pulley. Replacing that belt is a simply process with just a few steps and requiring only hand tools to complete. Working in the driveway or garage at home, most home mechanics can accomplish this job in about 20 minutes. A replacement belt for your Kia is available from any auto-parts store or through the Kia dealer.

Instructions

    1

    Open the hood of the car and remove the retaining bolt that holds the negative battery cable on the negative battery terminal using a wrench. Isolate the cable from the battery while you work.

    2

    Locate the adjuster bolt on the top of the alternator and loosen it with a wrench. Push the alternator toward the center of the engine, loosening the belt.

    3

    Remove the belt from the pulleys and discard it. Place the new belt around the crankshaft pulley, run it up and over the water pump pulley, then around the alternator pulley. Pull the alternator back, tightening the belt.

    4

    Tighten the adjuster bolt on the top of the alternator with a wrench, then check the tension on the belt. Press down on the belt between the alternator pulley and the water pump pulley. The belt should deflect about 1/8 inch.

    5

    Install the negative battery cable on the negative battery terminal and install the retaining bolt. Tighten the bolt with a wrench.

ReadMore

Monday, January 20, 2014

How to Replace a Key for a 2005 Honda Pilot

How to Replace a Key for a 2005 Honda Pilot

The 2005 Honda Pilot comes with special keys that include a built-in key fob for remotely locking and unlocking the vehicle. To work properly, each key fob has to be programmed to match a unique vehicle. The key part must be custom cut by a locksmith or dealer as the cutting is not the same as older Hondas and cant be cut by a traditional key-cutting machine. Blank Pilot keys are available through dealers or some auto parts suppliers.

Instructions

Replacing the Key Through a Dealership

    1

    Contact a Honda dealership parts department and ask for a replacement key.

    2

    Provide to the dealership the Vehicle Identification Number (VIN) and proof of ownership. The dealership will cut and program the replacement key to work with your vehicle.

    3

    Test the new key and fob to make sure it works properly with your Pilot.

Replacing the Key Through an Auto Parts Supplier

    4

    Purchase a replacement key from a parts supplier. Make sure the supplier provides programming instructions with the key in case the key has any nonstandard programming steps. If they do not, check the programming link in the article resources for instructions. The instructions are for a 2008 Pilot, but they should work for most Honda-compatible key fobs.

    5

    Follow the directions provided with the key. The directions will vary based on the key manufacturer. The directions will only be for programming the fob; the key will still need to be cut. Test the fob after programming to make sure it works with the Pilot.

    6

    Take the key to an automotive locksmith that provides Honda key cutting or to a Honda dealership. Provide the VIN so the key can be cut to work with your Pilot. The key is cut based on the VIN. Locksmiths usually charge a lower fee than dealerships to stay competitive.

ReadMore

Wednesday, December 11, 2013

How to Change the Front Axle U Joints in a 2005 Dodge

Dodge is a brand within the Chrysler auto manufacturing family. Their vehicles range from medium sized front-wheel drive sedans to commercial grade four-wheel drive trucks. The vehicles that send their power to the front wheels rely on continuous velocity joints, also know as U joints, to transfer torque while flexing. Without U joints, the front wheels could not bend and flex with the suspensions struts. However these joints are put under a lot of stress and need to be replaced if they break.

Instructions

    1

    Park the 2005 Dodge out of traffic and engage the parking brake. Turn the Dodge off and jack up the front of the vehicle with the car jack. Slide in the jack stands to keep the front of the car or truck elevated. Take off the front wheels with your tire iron and place them to the side.

    2

    Locate the front differential that connects the front half axles together. The half axles have U joints on each end so that they can flex independently. The U joints are a physical part of the half axles, so each half axle has to be removed and replaced. Unbolt the half axle from the shaft on the front differential and wrench the single bolt out of the U joint. Then wrench the bolt out of the shaft on the steering knuckle that connects to the other end of the half axle. Repeat this process on the other half axle.

    3

    Lift the new half axle into place and thread the bolts through the U joints by hand. First thread in the differential shaft U joint, then the steering knuckle U joint. Once both bolts are in, wrench the nuts down tight. Then repeat the process on the other half axle. Use the car jack to lift the steering knuckle up if it is too heavy for you.

    4

    Lower the Dodge off the jack stands. Then inspect the bolts in the U joints to make sure they are still tight. Turn the Dodge on. If you are in a four-wheel drive vehicle, shift into "4H." Listen for any banging or screeching that would indicate a loose half axle. Stop the car immediately and tighten the bolts if that happens.

ReadMore

Monday, December 2, 2013

How to Turn Off the Seatbelt Chime on a 2005 Chevy

How to Turn Off the Seatbelt Chime on a 2005 Chevy

You can turn off the seat belt chime on your 2005 Chevrolet yourself from your home garage. The chime is there to remind you that you need to fasten your belt, but many people find it very annoying. Just keep in mind that it is illegal to drive without your seat belt fastened in most states. So leave the chime intact if you live in one of these states, as turning off the chime wont allow you to use the seat belt.

Instructions

    1

    Call a junkyard and ask if they have any 2005 Chevrolet vehicles in your exact model. If they do, ask them if they have any seat belt assemblies. Some yards will remove the seat belt part for you, but you may have to do it yourself at others. If so, make sure you bring a Flathead screwdriver and a socket wrench set with you.

    2

    Cut the seat belt strap with scissors and remove the seat belt clip by sliding it from the seat belt strap.

    3

    Fasten the clip into the seat belt buckle on your vehicle. This will shut off the seat belt chime.

ReadMore

Friday, November 22, 2013

Where Is the Fuse Box for a 2005 Ford Escape

Where Is the Fuse Box for a 2005 Ford Escape?

The 2005 Ford Escape is a compact four door SUV that first came out in 2001. It has two fuse panels: the main panel and an additional power distribution box to house high current fuses. The fuses help to run electronic equipment like the lights, radio and power doors and windows.

Main Fuse Panel

    The main fuse box for the 2005 Ford Escape is on the passenger side of the center console near the instrument panel below the glove compartment. Remove the panel cover so you can access the fuses.

Power Distribution Box

    The power distribution box, which holds the high current fuses, is in the engine compartment on the right hand side. The high-current fuses keep the electrical systems from overloading.

Safety

    To safely replace fuses, make sure your cars engine and power are off. When replacing high current fuses, disconnect the battery before opening the panel to the power distribution box. Use the list of fuse codes in your owners manual, and the fuse puller tool in the main fuse panel to remove and replace fuses. Always replace the panel to the power distribution box before reconnecting the battery.

ReadMore

Tuesday, November 19, 2013

2005 Pontiac G6 Problems

2005 Pontiac G6 Problems

As of 2010, General Motors has issued two recalls on the 2005 Pontiac G6. One addressed a brake problem, while the other corrected owner manual instructions for child safety restraint systems. Intermittent power steering lock-ups and failures, a common problem with this model, have not yet resulted in a safety recall.

Brake Lights

    General Motors recalled 8,012 2005 and 2006 Pontiac G6 vehicles to repair a problem with the brake lights. A wiring connector could corrode and cause the brake lights to malfunction, both lighting up when the brake isnt being pressed and not lighting up when the driver is braking. This issue can also affect the cars cruise control, causing the driver to have to apply extra force to brake. If not repaired, this problem could lead to a traffic accident.

Child Restraint Equipment

    General Motors recalled 35,777 2005 Pontiac G6 vehicles to correct misprints in the owners manuals that could cause problems with installing child safety seats. The way the erroneous manual instructs the owner to install the child restraint system could cause the safety seat to be installed in a way that could potentially not protect the child in the event of a crash.

Power Steering

    Multiple consumer complaints to NHTSA indicate a common intermittent power steering problem in the 2005 Pontiac G6. The power steering may lock up or go out completely on these vehicles, which could lead to a dangerous accident. As of 2010, no recall has been issued to resolve this problem.

ReadMore

Friday, October 11, 2013

2000 2005 Monte Carlo Problems

2000-2005 Monte Carlo Problems

General Motors has issued multiple recalls of 2000-2005 Chevy Monte Carlos for problems ranging from fuel leaks to air bag defects. Engine fires, crashes or injury to vehicle occupants could result. Concerned vehicle owners may contact the National Highway Traffic Safety Administration (NHTSA) to determine whether their Monte Carlo vehicles may be affected.

Steering and Brakes

    In 2004, certain 2004 model year Monte Carlo vehicles were recalled because of problems with lower-than-required torque in the bolts mounting the front brake caliper to the steering knuckle. The bolts could break or back out, causing difficulties in steering and/or braking. In a separate recall, certain 2000-2007 Monte Carlos were recalled in 2009 for a broken steering knuckle problem.

Air Bags

    In 2002, thousands of model year 2002-2003 Monte Carlos were recalled due to a manufacturing problem with the drivers side air-bag inflator. If the air bag deploys, shards of the inflator could fly out and hurt someone in the car. A small number of 2003 Monte Carlos were subsequently under recall as well, to repair a separate defect that could cause the drivers side air bag to rupture.

Fuel System

    In 2004, certain 2000 model year Monte Carlos equipped with 3800 V6 (L36) engines and certain Delphi fuel pressure regulators were recalled because a fuel leak could occur and cause an engine backfire. Backfiring could cause the intake manifold to rupture and displace a fuel line, potentially causing fire. In 2007, various 1995-2005 Monte Carlos equipped with Delphi fuel pressure regulators were recalled for a similar fuel problem that could cause a fire.

Engine

    In 2009, 1998-2003 model year Monte Carlos equipped with 3.8L V6 naturally aspirated engines were recalled for dripping engine oil onto the exhaust manifold. This could cause an engine fire.

ReadMore

Sunday, October 6, 2013

How to Replace Map Lights for a 2005 Honda Civic LX

How to Replace Map Lights for a 2005 Honda Civic LX

The map lights on a 2005 Honda Civic are located on the interior ceiling, directly above the driver and front passenger. These lights are turned on by pressing on them with a finger. When these lights burn out, its an inconvenience for anyone who wants to read in the car at night or has to locate an object. The replacement of the map lights requires no special tools.

Instructions

    1

    Push in on the map light. Hold it in this position so that the seam between the map lights is more prominent.

    2

    Insert the flat-head screwdriver into the seam between the map lights.

    3

    Pry off the the map light cover. Use firm pressure but do not jerk or force the screwdriver to avoid breaking the plastic.

    4

    Remove the old bulb and replace it with a new one.

    5

    Reattach the light cover. Apply pressure with the palm of your hand until the cover snaps into place.

ReadMore

Thursday, October 3, 2013

Is There a Way to Get the Power Window Up When the Switch Is Bad in a 2005 Chevy Equinox

The power window assembly in a 2005 Chevrolet Equinox is controlled by a switch thats mounted in a switch panel in the center of the dash board, just behind the shifter. This switch panel contains four switches; one for each window. The switches connect to wires that run to grounds, relays, and fuses within the vehicle. Because of the complex wiring system needed to control the window, its not possible to bridge any of the terminals or manipulate the wiring to raise or lower the window without using the switch. Unfortunately, if the switch fails, the switch panel needs to be replaced in order to raise or lower the window.

Instructions

Removal

    1

    Grip the bottom of the center column trim bezel. Pull up gently on the bottom of the bezel to detach it from the center column.

    2

    Work around the column trim bezel, gently pulling up at the edges until the entire bezel is detached from the vehicle.

    3

    Disconnect any electrical connectors from the back of the trim bezel, including the window switchs electrical connector.

    4

    Remove the screws holding the switch assembly to the bezel with a screwdriver, then remove the switch assembly.

Installation

    5

    Set the new window switch panel into position on the bezel. Reinstall and tighten the screws to 22 inch-pounds with a torque wrench.

    6

    Reconnect the window switch panels electrical connector. Reconnect any other electrical connectors from the car to the bezel.

    7

    Set the bezel into position and press down around its circumference in order to seat all of the retaining clips. Test the window switches to ensure that they work properly.

ReadMore

Thursday, September 26, 2013

How to Replace Belts on a 2005 Mitsubishi Endeavor

Replacing the serpentine belt on the Mitsubishi Endeavor is necessary if the belt is starting to stretch, has damage on it, or is extremely worn. The belt drives all the accessories on the front of the engine and if it fails, the engine may overheat, the alternator will not produce electricity and the power steering will not work. Replacement belts are available at most auto-parts stores. Check your serpentine belt often and replace it before it breaks.

Instructions

    1

    Locate the negative battery cable on the negative battery terminal. Remove the retaining bolt from the battery cable end with a wrench, then remove the cable from the battery. Isolate the cable from the battery terminals while you are working on the belt.

    2

    Locate the belt tensioner on the front of the engine between the alternator and the water pump. Loosen the axis bolt, the bolt in the center of the tensioners pulley, with a socket and ratchet but do not remove it.

    3

    Locate the adjusting bolt on the bottom of the tensioner, just below the pulley, then turn it counterclockwise with a socket and ratchet until the belt is loose. Remove the belt from the pulleys and discard it.

    4

    Install the new belt over the pulleys, following the same path as the original belt, then tighten the adjustment bolt by turning it clockwise. Tighten the belt until you can push the belt down 1/8- to -inch between the pulleys.

    5

    Tighten the axis bolt on the tensioner pulley with a socket and ratchet. Install the negative battery cable on the negative battery terminal, install the retaining bolt and tighten it with a wrench.

ReadMore

Sunday, September 22, 2013

How to Disable the Seatbelt Chime in a 2005 Chevy

Some 2005 Chevrolets come with a seat-belt chime to remind you to fasten your seat belt whenever you start the vehicle. Many people find it very annoying. But there is a way to disable it, and you can change it back if you change your mind. If you are someone who always forgets to put on your seat belt, keep in mind that in many states it is illegal to drive without your seat belt fastened. In that case, it may not be such a bad idea to retain the seat-belt chime as a quick reminder.

Instructions

    1

    Find a junkyard and ask the dealer if he or she has a 2005 Chevy of the same model as yours. If so, go to the junkyard with a pair of scissors and cut the seat belt clip off of the strap. You may have to remove the whole seat-belt assembly first or the junkyard dealer may have one already. Alternatively, you can call your local auto parts store and see if they sell a seat belt clip that will fit your buckle. The sales person can determine which size to sell you based on your vehicle identification number.

    2

    Put the seat-belt clip into the seat-belt buckle on your Chevy. This will turn off the sea-tbelt reminder. When you are ready to fasten your seat belt, remove the junkyard seat-belt clip and put on your seat belt.

    3

    Pull out the seat belt as far as it will go and wrap it around the back side of your drivers seat. Clip the seat-belt clip into the seat-belt buckle. This will stop the chiming.

ReadMore