Pages

Showing posts with label 1990. Show all posts
Showing posts with label 1990. Show all posts

Sunday, April 20, 2014

How to Jump Start a 1990 535I BMW

How to Jump Start a 1990 535I BMW

The battery in a 1990 5-series BMW is designed to be a reliable as the car. There are occasions, however, when the battery goes flat. It usually comes as a surprise when the engine doesnt fire at the turn of the key. For this reason, its a good idea to know how to safely and correctly jump start your BMW. The battery on this model is located under the back seat, but the jump-start position is under the hood. Its marked with a one-inch plastic "plus" symbol. You will need another car with a live battery to do the job.

Instructions

    1
    Try the ignition first to troubleshoot the battery.
    Try the ignition first to troubleshoot the battery.

    Determine that the battery is the reason the engine wont start. Turn the ignition. If the engine cranks, the battery is good. If theres silence or a ticking sound, the battery is faulty.

    2
    Attach the positive clamps first.
    Attach the positive clamps first.

    Turn the ignition off. Lift the hood of both vehicles. Locate the positive post under the hood of the BMW 535i. It connects to the clamp of the positive (red) cable. Attach the clamp on the other end of the red wire to the positive terminal on the booster vehicle.

    3
    Attach the negative terminals last.
    Attach the negative terminals last.

    Attach the negative (black) clamp to the negative terminal of the booster battery. Attach the other negative clamp to the engine frame of the BMW to complete the circuit. Any unpainted metal surface will suffice. Just make sure its away from any moving parts.

    4
    Run the booster cars engine for a few minutes before trying to start the BMW.
    Run the booster cars engine for a few minutes before trying to start the BMW.

    Start the engine of the booster vehicle. Wait at least 5 minutes for a charge to build up. Start the BMW. If it starts, move on to the next step.

    If it fails to start, wait another few minutes and try again. If the car still fails to start after 30 seconds of trying, call a professional mechanic. The battery might not be at fault, and further tries could damage your engine.

    5
    Remove the cables in reverse order.
    Remove the cables in reverse order.

    Remove the cables in the reverse order they were attached: the BMW engine frame first, and the booster batterys red terminal last.

    6
    Charge the battery for at least 12 hours.
    Charge the battery for at least 12 hours.

    Drive the BMW to a location where you can safely remove the battery and attach it to a battery charger for at least 12 hours. The vehicles alternator will provide some charge to the battery as you drive, but this is not its primary function.

ReadMore

Sunday, April 6, 2014

The Location of the Oil Pan Sensor in a 1990 Mazda MPV

The oil pan or oil level sensor in your Mazda MPV monitors the amount of oil in the oil pan. The sensor has an electrical connection that enables it to communicate with the PCM (power control module). When the oil level reaches or falls beneath the sensor, it illuminates the oil light in your MPVs dash cluster. Damage to the oil level sensor most often results from electrical failure. You can located and replace the oil pan sensor on your 1990 Mazda MPV right at home. The job should take you approximately 30 minutes.

Instructions

    1

    Place a wheel block firmly into position behind both of your MPVs rear tires.

    2

    Apply the emergency brake and raise the front end of your vehicle with a hydraulic jack. The bottom of both of the front tires should visibly measure no more than 8 inches from the ground.

    3

    Set a jack stand behind the front tires underneath your MPVs frame rail. Lift the support arms on both jack stands to 85 percent of the height of the hydraulic jack.

    4

    Lower the hydraulic jack slowly while you monitor both of the jack stands. When you see that your MPV securely rests on the support arms of the jack stands, stop lowering the hydraulic jack. Do not completely remove or lower the hydraulic jack. Leave it in its position for extra support.

    5

    Slide under your Mazda MPV and locate its oil pan. The oil pan sits at the lower, rear of the engine. It looks like a black, metal rectangle and has 20 small bolts around its upper lip. The oil pan also has a large bolt at the bottom of it used to drain the oil.

    6

    Locate the oil pan sensor on the lower side of your oil pan. You will not be able to see the sensors length but you should see the wiring harness connected to the top of it. On some models of the 1990 Mazda MPV, the sensor mounts just above the oil draining bolt. On other models, the sensor mounts on the opposite side of the oil pan across from the oil draining bolt.

ReadMore

Sunday, March 16, 2014

How do I Troubleshoot a 1990 GM Truck That Wont Start

How do I Troubleshoot a 1990 GM Truck That Wont Start?

General Motors makes a wide variety of trucks for the consumer, but all of them rely on gas and a battery to start. If you are having problems starting your GM truck, you can troubleshoot the problem by taking a look at these two components. When your battery has a low charge or is dead, the trucks motor will not be able to fire up. GM trucks require gasoline to run, so a low fuel tank could be the culprit to your truck not starting.

Instructions

    1

    Turn the key in your GM truck to get the gauge readings. Check the fuel level and make sure you have enough fuel to start the truck. Add fuel if needed.

    2

    Pop the hood on the GM truck and locate the battery. Use a socket wrench to disconnect the battery terminals from the battery. Clean the battery terminals with a wire brush and a can of soda if corrosion has set in.

    3

    Reattach the battery terminals to the battery and start the truck.

    4

    Jump start the truck with jumper wires and another vehicle. Allow the truck to run for about five minutes and then turn it off.

    5

    Try to restart the truck. If the truck doesnt restart, you will need to replace your battery.

ReadMore

Sunday, February 16, 2014

How to Bleed a 1990 Honda Accord Clutch

How to Bleed a 1990 Honda Accord Clutch

The Honda Accord is the mid-level offering in Hondas Civic, Accord and Camry line of cars. In 1990, the Accord was made 5 inches longer. It received a larger 2.2-liter, four-cylinder engine and two new transmissions, a five-speed manual or a four-speed automatic. The five-speed manual transmission features a hydraulically actuated clutch, with a master cylinder mounted on the firewall next to the brake master cylinder and a slave cylinder mounted on the bell housing.

Instructions

    1

    Raise the front of the Accord with a jack and support it with jack stands on each side of the vehicle.

    2

    Locate the clutch master cylinder next to the brake master cylinder. Clean the top of the master cylinder with a shop rag. Fill the cylinder with fresh brake fluid if necessary.

    3

    Put on safety goggles. Loosen the bleeder screw on the clutch slave cylinder with a wrench but do not open it yet. The clutch slave cylinder is located on the drivers side of the car on the bell housing. Fill a plastic bottle about 1/3 full of brake fluid. Attach a 3-foot length of clear plastic tubing to the bleeder screw and insert the other end into the plastic bottle so it is below the level of the fluid.

    4

    Instruct an assistant to depress the clutch pedal three or four times and then hold pressure on the pedal. Open the bleeder screw with a wrench while your assistant maintains pressure on the pedal. Brake fluid and air bubbles will exit the slave cylinder. Close the bleeder screw. Your assistant can now release the pressure on the clutch pedal.

    5

    Check the fluid level in the master cylinder. You must keep checking the fluid level, as you bleed the slave cylinder, because it will go down every time you open the bleeder screw. Repeat the above process until no air exits the slave cylinder.

    6

    Wipe up any spilled brake fluid with a shop rag. Raise the front of the vehicle with the jack and remove the jack stands. Lower the vehicle. Make sure the master cylinder is full.

ReadMore

Saturday, February 8, 2014

1990 Mazda Rx7 Airbag Information

1990 Mazda Rx7 Airbag Information

The Center for Auto Safety (CAS) has recieved numerous consumer complaints concerning Mazda RX-7 seat belt failure and airbag defects. Seat belts failing to properly restrain passengers have been an issue for Mazda since 1977. In newer Mazdas, airbags have been trouble prone, states Clarence Ditlow of the CAS.

Recalls

    The 1990 Mazda RX-7 airbags have never been recalled, according to Consumer Guide. However, Anapol Schwartz attorneys list a recall of 1990 Mazda RX-7 frontal airbags. According to the attorneys, threaded inflator components of the airbags may have been damaged during assembly. This may have allowed airbag components to separate when deploying the air bag. The separation in the faulty airbags allows hot combustion gases to escape into the passenger area, which could result in injuries.

Models

    According to Edmunds, both side and curtain airbags come stock in all 1990 Mazda RX-7 models, including the Base, GTU, Turbo, GXL and 2+2 GXL.

Tests

    The Mazda RX-7 of 1990 has no safety test information available about the airbags from either the NHTSA or IIHS.

ReadMore

Thursday, November 28, 2013

How to Install TPS on a 1990 Ford F 350 5 8L

The 1990 Ford F-350 truck was available with three engines: a 5.8L Windsor engine, a 7.3L engine, a 7.5L engine, and a 4.9L engine. The 5.8L engine, like the others, comes with a throttle position sensor, also called a TPS. The throttle position sensor helps to regulate the trucks idle. If its faulty, the idle may be high, low, or otherwise irregular. Removing the old TPS and installing a new one shouldnt take you longer than 15 minutes.

Instructions

    1

    Turn off the F-350s engine. Gather your tools and replacement throttle position sensor.

    2

    Open the F-350s hood to view the 5.8L engine. Move to the passenger side of the engine compartment. Look in the center, behind the intake manifold, right next to the area the large black air hose comes from. Youll see the throttle position sensor mounted next to the air hose. The sensor looks similar to a capital "T." The top part of it is wide. The bottom part (the connector) is thin. It is a black plastic piece.

    3

    Push the tab on the TPS electrical connection and unplug it from the sensor. The connection is attached to the thin part of the throttle position sensor.

    4

    Remove the two screws with a Phillips screwdriver. Carefully pull the TPS away from its mount.

    5

    Insert and seat the new throttle position sensor in its mount. Insert and tighten the two screws. Plug in the electrical connection. Shut the hood.

ReadMore

Tuesday, November 26, 2013

How to Get Another Key for a 1990 Honda Prelude

Maybe youve lost the key to your Honda Prelude, your key no longer works correctly or you just want to have a spare key on hand. Obtaining a new car key, even for an older model vehicle, is not difficult. Honda vehicles are equipped with key codes that are personalized for each individual vehicle. As long as you can provide the vehicle identification number (VIN), which contains the key code for your 1990 Prelude, to a professional key maker, you can obtain a new key.

Instructions

    1

    Locate the vehicle identification number (VIN) on your 1990 Honda Prelude. You can find this number in the original purchase paperwork, on the title or on your insurance information. It is also located on the doorjamb on the drivers side and is visible only when the door is open.

    2

    Call your local Honda service department or a professional locksmith to order a new car key. If you call Honda, you will have to pick up your key when it is ready whereas a locksmith might come to you.

    3

    Provide your VIN to the Honda service department or locksmith. This number will allow the service technician or locksmith to read the key code for your car and cut the key correctly.

    4

    Provide proof that you are the owner of the vehicle for which you are requesting a new key. You will need to show the Honda service department or the locksmith your photo identification and proof of ownership such as the vehicle registration, insurance card, or purchase paperwork with your name on it. You can then pay for your new key.

ReadMore

Wednesday, November 13, 2013

How Do I Install a Fuel Pump in a 1990 Ford Ranger

The Ranger is a pickup truck that Ford has produced since 1983. The 1990 Ford Ranger was equipped with either a 6-cylinder 2.9-liter engine or a 6-cylinder 4.0-liter engine, each of which uses fuel injection. The Ranger has an electric fuel pump in the fuel tank that produces low pressure. The pump is part of the fuel gauge sending unit, and you have to remove the entire unit if you need to replace the fuel pump and install a new one.

Instructions

    1

    Loosen the cap on the fuel tank and remove the air filter. Disconnect the cable from the negative battery terminal. Remove the valve cap from the pressure relief valve on the fuel rail. Connect fuel pressure gauge tool T80L-9974-A to the pressure relief valve. Open the pressure relief valve to relieve the pressure in the fuel system. Disconnect the fuel pressure gauge and replace the valve cap.

    2

    Drain the fuel from the fuel tank. Support the fuel tank with jack stands. Release the clamp on the fuel tanks fill pipe. Disconnect the bolts for the skid plate and remove the skid plate and its brackets from the fuel tank. Disconnect the bolts for the front and rear straps of the fuel tank and remove the straps. Release the clamp for the fuel sender units fuel hose. Remove the fuel lines from the fuel sender unit. Lower the tank from the Ranger with the floor jacks. Remove the shield from the fuel tank.

    3

    Detach the electrical connector from the fuel system sender unit. Clean the fuel tank around the fuel sender unit with a shop rag. Turn the locking ring on the fuel sender unit counterclockwise with a hammer and brass drift. Remove the locking ring from the fuel sender unit and pull the fuel sender unit from the fuel tank. Discard the sealing gasket. Detach the fuel pump from the fuel sender unit.

    4

    Insert the new fuel pump into the fuel sender unit. Put a new sealing gasket on the fuel tank. Place the fuel sender unit into the fuel tank and align the fuel senders tabs with the fuel tanks slots. Attach the locking ring to the fuel sending unit and turn it clockwise until the ring tab is against the stop. Attach the electrical connector for the fuel sender unit.

    5

    Reinstall the fuel tank. Reconnect the negative cable on the battery. Turn the ignition on for five seconds, then turn it off. Repeat at least five times to pressurize the fuel system. Start the engine and check for fuel leaks.

ReadMore

Thursday, October 17, 2013

Specifications for a 1990 Honda Rebel 250

Specifications for a 1990 Honda Rebel 250

The Rebel 250, also known either as the CMX250 or the CMX250C, is a cruiser-style motorcycle manufactured by Honda. Introduced in 1985, it was retired by 1987 and re-introduced in 1996. As of November 2010, it is still in production as an entry-level motorcycle.

Engine Specifications

    The Honda Rebel 250 includes a 234cc, SOHC parallel twin-cylinder engine with a 53-millimeter bore and stroke. It is also built with a single 26-millimeter diaphragm-type constant-velocity (CV) carburetor, an automatic cam-chain tensioner and maintenance-free CD ignition with five-speed transmission.

Handling Specifications

    The front suspension of the Honda Rebel 250 includes a 33-millimeter hydraulic fork that combines with the five-way dual shocks of the rear suspension to provide optimum steering and control. It also consists of a single-disc front brake with a twin-piston caliper and a drum rear brake.

Dimensions

    The 331-pound Honda Rebel 250 includes a 30-degree rake that measures at 40 inches and a trail of 4.4 inches. With a seat height of 26.6 inches and a wheelbase of 57.1 inches, it also includes a 2.6-gallon fuel tank with a 0.7-gallon reserve.

ReadMore