Friday, April 25, 2014
How to Clear a Service Engine in an Acura
Your Acura generates and stores fault codes whenever there is a problem with a solenoid, valve or sensor. This will show up on your instrument panel as "Service Engine" or other warning light. Once you have the codes checked and the vehicle serviced by a qualified mechanic, you need to clear the codes. Usually the mechanic can and will do this, but not always. Not only is it annoying to have the light remain on your instrument panel, it is also bad for the vehicles computer, which may not able to keep track of when your next servicing is due. You dont need any special tools to clear the service engine light on your Acura. Its a relatively easy fix.
Instructions
- 1
Put the key into the ignition and turn the engine to the "off" position on your Acura.
2Find the reset button on the odometer located on the instrument panel. Press and hold this button while simultaneously turning the key in the ignition to the on or "II" position.
3Hold the button for about 10 to 15 seconds, then release it. The "service engine soon" light will go out.
4Turn off the vehicle, then turn the engine on. Verify that the "service engine soon" light is still off.
Monday, April 21, 2014
How to Repair Clear Coat Bubbles
It can be disheartening when repainting your automobile to see bubbles in your final stage of applying the clear coat. After all the work you put into sanding, primer and paint, it is all too easy to see your labor marred by these tiny bubbles, also known as fish eyes. These can be caused by a variety of things, including tiny bits of oil, water or dirt. Even passing diesel exhaust fumes can cause fish eyes in your clear coat. You can repair them, but it is a time-consuming process.
Instructions
- 1
Wet sand the bubbled portion of your automobiles surface using extra-fine sandpaper and water. You must sand away all of the clear coat on the affected portion. For example, if there are bubbles on the hood of your car, you must sand the entire hood, not just the bubbles. Always keep your sanding area wet, and gently sand away the clear coat. Do not sand too hard, or you may remove the paint.
2Wash and rinse the sanded areas of your automobile thoroughly to completely remove all debris from the surface. If there is any debris remaining, fish eyes will form again when you reapply the clear coat. Allow the surface to completely dry since water can also cause bubbling in the clear coat.
3Mix fish eye preventer and clear coat in your paint sprayer according to the fish eye preventers instructions. The preventer is silicon-based, and can compensate for tiny bits of oils or debris in the atmosphere that could potentially cause fish eyes.
4Spray the clear coat and fish eye preventer mixture on the affected portion of your automobile. Use a smooth, even motion. If you plan to apply more than one coat, make sure that the preceding coat is completely dry. If the preceding coat is still wet, this could also cause bubbles to form.
Wednesday, February 26, 2014
Auto Clear Coat Urethane Safety
Urethane clear coats are applied to create a lasting shine and to provide protection for the base colors that lay underneath them. As with any solvent-based materials, safety guidelines always should be followed when urethane products are used.
Inhalation
Urethane clear coats contain harmful vapors. The product always should be used in a well-ventilated area or in closed conditions where extraction is available. Users should wear suitable air-fed respiratory equipment at all times.
Skin and Eyes
Contact with skin and eyes should be avoided at all times. Protective clothing, eye-wear and gloves always should be worn during handling. In the event of accidental spillage, urethane clear coats should be washed off with copious amounts of water and medical advice should be considered.
Consumption
Urethane clear coats should never be consumed internally. If accidental swallowing occurs, do not induce vomiting and seek medical advice immediately.
Usage
Always use urethane clear coats in accordance with manufacturer instructions and never use non-compliant solvents to help harden or thin the material. Users with respiratory problems should avoid contact with all urethane-based products.
Friday, February 7, 2014
How to Clear Trouble Codes From My 1995 Dodge Truck
1995 Dodge trucks use a system called an On-Board Diagnostics computer to monitor the vital functions of the vehicles. When any of a trucks systems fail, it causes a warning light to illuminate on the instrument panel. The computer also keeps track of the trucks regular servicing needs. After the Dodge has been serviced or repaired, you or your mechanic will need to clear the trouble codes from the computer using a diagnostic code scanner. This can be purchased from any auto parts store.
Instructions
- 1
Open the drivers door and find the diagnostic scanner port. You can find it on the underside of the drivers dash.
2Push the diagnostic code scanners connector cable into the diagnostic port on the Dodge.
3Put the key into the ignition and turn it to the "run" position, taking care not to start the engine.
4Search the trouble codes using the instructions in the manual that came with the scanner. When it is finished, press the command "Clear Trouble Codes."
5Disconnect the scanner and turn on the engine. Verify that all warning and service lights have shut off.