Pages

Showing posts with label 2007. Show all posts
Showing posts with label 2007. Show all posts

Saturday, May 3, 2014

How to Change the Brake Light Bulb on a 2007 TrailBlazer

In 1983, Chevrolet introduced a mid-sized SUV to the market, known as the Blazer. The Blazer gave drivers the usefulness of an SUV, without the bulk of a full-sized SUV. In 2002, the Trailblazer replaced all four-door Blazers and finally, in 2006, the Trailblazer replaced the Blazer altogether. The 2007 Trailblazer came standard with a 4.2-liter, in-line six-cylinder engine that produced 291 horsepower and 277 foot-pounds of torque. The 2007 Trailblazers styling was similar to that of its Blazer predecessor, including the vertical taillight assemblies. Replacing the brake light bulbs in these vertical taillight assemblies is a relatively easy task.

Instructions

    1

    Open the rear hatch and remove the two screws on the inner part of the taillight assembly with a Phillips screwdriver.

    2

    Pull the taillight assembly rearward to remove it from the Trailblazers body. Unplug the wiring harness from the rear of the taillight assembly, by pressing the locking button and pulling the harness away from the assembly.

    3

    Turn the taillight assembly over and remove the three screws holding the socket plate -- the roughly 2-by-5-inch plastic plate on the rear of the taillight assembly. Pull the socket plate from the taillight assembly; notice the bulbs remain attached to the plate.

    4

    Pull the burnt-out brake bulb from the socket plate with a slight wiggling motion. Grab a new 3157 brake light bulb with a clean, lint-free cloth and press it into the socket. Never touch the glass part of the bulb with your bare hands, as the oils from your hands can cause the bulb to burn out prematurely.

    5

    Set the socket plate back on the rear of the taillight assembly and tighten the three screws with a Phillips screwdriver.

    6

    Plug the wiring harness back into the socket plate and set the taillight assembly back on the rear of the Trailblazer. Tighten the two screws on the inner part of the taillight assembly with a Phillips screwdriver.

    7

    Close the Trailblazers hatch.

ReadMore

Sunday, October 27, 2013

Chevrolet Avalanche 2007 Recommended Service

Those interested in buying a used full-size pickup truck may consider the Chevrolet Avalanche. The 2007 and 2008 models are almost identical except for side-curtain airbags and On-Star with GPS navigation available in 2008. Following manufacturer recommend maintenance extends engine and transmission longevity.

Oil Changes

    The Chevy Avalanche featured a "change engine oil" indicator within the instrument cluster that illuminated when an oil change was required. Chevrolet suggests changing the oil within 600 miles of the indicator light illuminating.

Fluid Replacement

    Chevrolet recommends changing the transmission fluid at 50,000 miles when driven in heavy traffic areas, rough terrain or in extreme hot or cold weather environments. Replace the transmission fluid every 50,000 miles thereafter when driven hard. For lighter driving, replace the transmission fluid at 100,000 miles and again at 200,000 miles. Change the transfer case fluid at 50,000 miles and then every 50,000 miles thereafter.

Air Filter Replacement

    At 50,000 miles, replace the engine air cleaner filter and transmission fluid filter. Replace both filters again at 100,000 miles. Chevy recommends replacing the engine air cleaner and transmission fluid filter every 50,000 miles.

ReadMore

Friday, September 27, 2013

How Do I Install a Brake Controller on a 2007 Chevrolet Suburban

The Chevrolet Suburban is a large sport utility vehicle that has the same platform as the Chevrolet C/K series of pickup trucks. The 2007 model has an anti-lock braking system (ABS), like most vehicles of this period. The ABS uses a brake controller, known as an electronic brake control module (EBCM), to determine the amount of braking force to apply to the wheels. The procedure for installing a brake controller in a 2007 Suburban is the same for similar vehicles such as the Escalade, Tahoe and Yukon.

Instructions

    1

    Disconnect the cable from the negative terminal of the battery with a socket wrench. Raise the vehicle with a floor jack and support it on jack stands.

    2

    Locate the EHCU under the vehicle on the drivers side next to the driveshaft. The EHCU is an assembly consisting of the EBCM, the brake pressure modulator valve, or BPMV, and a mounting bracket. It is roughly the shape of a cube 3 inches on a side when it is fully assembled. Wash the area around the EHCU to remove any dirt.

    3

    Disconnect the mounting screws for the EBCM with a socket wrench, and detach the EBCM from the brake pressure modulator valve (BPMV). The BPMV is the small box-shaped component that is connected to the brake lines. Clean the mounting surface on the BPMV with a clean shop rag.

    4

    Mount the new EBCM to the BPMV, and fasten new screws to the EBCM with a socket wrench. Lower the vehicle with the floor jack, and attach the cable to the negative battery terminal.

    5

    Connect a scan tool to the vehicles data link connector, and program the new EBCM using the scan tools tire-size calibration function. Turn the ignition on and perform the diagnostic system check.

ReadMore

Saturday, September 21, 2013

How to Install a Mirror on a 2007 Dodge Caravan

Car mirrors can suffer a lot of damage throughout the life of an automobile. When a mirror is beyond repair, the entire mirror must be replaced. Knowing how to install a mirror on a 2007 Dodge Caravan can spare Caravan owners time and expense.

Instructions

    1

    Pry off the panel where the mirror attaches to the vehicle with a small standard screwdriver. This will expose the screws attaching the mirror to the vehicle.

    2

    Remove the two exposed screws attaching the mirror to the vehicle with a T27 Torx driver.

    3

    Open the door next to the mirror you are replacing. This will expose the third and final screw attaching the mirror to the vehicle.

    4

    Unscrew the final screw with a T27 Torx driver. Some mirrors designed for a 2007 Dodge Caravan have an internal heating element with a cable attaching it to the vehicles electrical system. With this type of mirror, press the release tab on the cable connector and pull the cables apart before removing the mirror.

    5

    Lift the mirror to be replaced away from the vehicle.

    6

    Hold the replacement mirror in place against the vehicle so the screw holes in the mirror base and vehicle align. If the vehicles mirror has an internal heating element, first attach the replacement mirrors cable to the vehicles mirror cable before holding the replacement mirror in place.

    7

    Screw the screws into the three holes of the mirror base with a T27 Torx driver.

    8

    Replace the panel where the mirror attaches to the vehicle by sliding it into place and pressing firmly.

ReadMore