Wednesday, October 15, 2014
How do I Install a 99 Avenger Wheel Hub Assembly
Wheel bearing failure is a common cause of driving troubles that may lead to damage of the cars drivetrain, or at the very least cause some obnoxious noises. The Dodge Avenger features maintenance-free wheel bearings. As a result, when the bearings no longer operate properly they must be replaced with the entire wheel hub assembly. This procedure requires removal of the steering knuckle, so it may be beneficial to consider replacing other elements of the steering and drivetrain during this repair to avoid future frustration.
Instructions
- 1
Loosen the wheel hub bolt and remove the wheel cotter pin. Raise the front of the vehicle and support it on jack stands, then remove the wheel.
2Remove the steering knuckle from the vehicle. This will require removing the brake calipers from the rotor and disengaging the tie rod ends and the lower ball joint. Doing this will require the use of a tie rod presser and a ball joint separator tool.
3Remove the bolts holding the wheel hub to the steering knuckle once the knuckle has been removed from the vehicle. It is recommended to do this on a bench or other solid surface. Remove the hub from the steering knuckle by gently tapping it with a soft mallet.
4Clean the mating surface between the steering knuckle and the wheel hub. Install the new hub assembly and tighten the bolts to 65 foot-pounds of torque.
5Reinstall the steering knuckle and the brake calipers. Install the tire and lower the vehicle. Tighten the wheel hub nut and install a new cotter pin. Drive the vehicle to check for proper alignment.
Friday, April 4, 2014
How to Replace the Wheel Cover on a 2009 HHR
Replacing the wheel cover on your 2009 HHR involves one of the preliminary steps necessary to change a tire, and its a fairly simple process. Botching one of the steps, however, or forgetting to ensure the security of your replacement cover could result in damage to your car or even an accident, as covers can go flying if they arent properly secured. Replacing the wheel cover on your 2009 HHR requires thoughtful attention to both the removal of the old cover as well as the placement of the new cover.
Instructions
- 1
Pry the cover off of your HHRs wheel using a flat-head screwdriver or the flat end of your lug wrench. There will be a small insertion point into which you can place the screwdriver or the lug wrench. A simple prying motion will release the wheel cover.
2Position the new wheel cover so that the valve stem in the tire extends through valve-stem hole in the wheel cover. Standard HHR tires have 16-inch wheels, so you will need 16-inch replacement covers unless you have modified your HHR with different tires.
3Secure the wheel cover in place by hand. There is a seam running along the edge of the wheel into which the inner edge of the wheel cover will fit securely. You should be able to move your hands away from the wheel without the wheel cover falling off.
4Tap around the edges of the wheel cover gently with a soft mallet, hammer or the edge of the lug wrench, depending on how caul you want to be in handling your new wheel cover.
Friday, January 31, 2014
Portable Wheel Alignment Tools
Wheel alignment is one of the important tasks undertaken during vehicle maintenance. It is the relationship of the automobile wheels to the vehicle itself, to each other and to the road. The main purposes of conducting wheel alignment is to ensure the vehicle is stable on the road, to reduce the amount of wear on tires and to produce the least amount of moving resistance. Incorrect wheel alignment can be very dangerous because it can seriously affect handling and vehicle safety. Wheel alignment mainly involves three major measurement angles: the caster, the camber and the toe.
EZ Line Laser Wheel Alignment Tool
The EZ Line laser is a tool kit used for aligning different systems such as wheels and axles of vehicles such as heavy-duty trucks and trailers. One of its main advantages is that it is compatible with vehicles that use toe settings. This tool kit comes with magnets which are attached directly on the vehicle system, a 32-inch measuring tape and two magnetic fifth-wheel pin adapters. It has the ability to capture measurements in less than ten minutes. If the laser goes through the center of the magnet when shot, then the automobile system wheels are properly aligned. If not, the same lasers are used to align the wheels properly.
Camber Caster Gauge
A camber caster gauge is a small, portable device that is attached at the end of the axle on a wheeled vehicle in order to zero out the measurement dials. It captures measurements of the camber and the caster of a wheeled vehicle. Camber ers to the tip of the tire and wheel while caster is the angle of tilt of the kingpin. When the caster is tipped toward the center of the kart, the measurements are considered positive; toward the front of the kart, the measurements are negative. As for the camber, if the kart is tipped toward the center, the measurements are considered negative. If it is to the outside, the measurements are positive.
Laser Wheel Alignment Gauge
The laser wheel alignment gauge is a battery-operated and portable device which is easy to use and calibrate. It has the capability of taking fast measurements from automobiles and has a calculator for converting measurements. It produces measurements of the combined toe angle with high precision. It constitutes the laser, laser target plate and a mirror. This gauge produces clear laser lines which ensure fast and accurate readings.
Sunday, December 8, 2013
The Components of a 4 Wheel Drive System
Four-wheel drive vehicles receive torque from the engine in all four wheels at the same time. The original concept was to be able to maintain traction to either haul extra weight or drive in tough road conditions, or both. There are two modes of 4-wheel drives. The part-time mode is used for off-road driving or loose road surfaces. The driver is able to switch from 2-wheel drive to 4-wheel drive as needed. Full-time mode is used in all road conditions all of the time.
Differentials
The 4-wheel drive has a differential between the two front wheels and another between the back wheels. During a turn, all wheels are going at different speeds while at the same time, the inside wheels are following a different path than the outside wheels. The differentials allow front, back, left and right wheels to spin at different speeds during a turn by sending the power from the engine to the wheels. The differentials slow the transmissions rotational speed before it hits the wheels. In this manner it behaves as the last gear reduction of the vehicle.
Transfer Case
The transfer case is said to be the component that defines a vehicle as 4-wheel drive. This device splits power between all four axles on the vehicle. The transfer case is used to lock the front and rear axle drive shafts to force the wheels to have the same speed when they are turning. On part-time 4-wheel drive systems, transfer cases have an extra set of gears. These gears give a low range to the vehicle, providing extra torque.
Drive Shaft
Drive shafts enable the transfer case to transmit power from the drive to the front and back axles. The drive shafts are enclosed inside axle housings and transmit the drive to the tires. In part-time 4-wheel drive vehicles the drive is transmitted through the front axle drive only when the driver uses 4-wheel drive.
Locking Hubs
Every vehicles wheels are bolted to a hub. Part-time 4-wheel drive vehicles are equipped with locking hubs that are designed to disconnect front wheels from the front differential when 4-wheel drive is not engaged. The locking hubs also disconnect the front wheels from the drive shaft when a car is in 2-wheel drive.
Electronics
Electronically controlled clutches are used on some 4-wheel drive vehicles. This type of clutch controls torque transfer between the tires in a much more effective manner than older clutch mechanisms. Many 4-wheel drive systems use Anti Lock Brake Systems (ABS). The ABS systems provide brake-traction control when the tires begin to skid.
Sunday, November 24, 2013
How to Replace the Rear Axle Wheel Bearings in a 1999 Ford Expedition
The 1999 Ford Expedition is built on an F150 platform. The Expedition uses a 9.75-inch rear axle. The axles are retained with C-clips at the end of the axle shaft, inside the differential carrier. The axle bearings are of the roller type. A failed axle bearing can manifest itself as a noise at the rear wheel or gear oil leaking past the oil seal. When replacing axle bearings, the oil seals must also be replaced.
Instructions
- 1
Park the Expedition on a flat, paved surface, and do not set the parking brake. Place wheel chocks in front of the front wheels. Loosen the lug nuts on the rear wheels, then raise the rear of the Expedition with a jack, and support it with jack stands. Finish removing the lug nuts and rear wheels.
2Remove the rear brake drums. For disc brakes, use a ratchet and socket to remove the lower caliper mounting bolt and loosen the upper bolt. Pivot the caliper up and away from the rotor. Remove the rotor.
3Position a drain pan under the differential housing. Remove the bolts that hold on the carrier cover with a ratchet and socket. Catch the gear oil in the drain pan. Remove the old cover gasket, and use a gasket scraper to remove any material from the cover and the differential housing. Wipe both surfaces with a shop rag.
4Examine the carrier assembly inside the housing, and youll see the large vertically mounted ring gear. Next to the ring gear, running through the carrier housing, you will see the pinion shaft. Rotate the carrier assembly until youre looking at the end of the shaft. It runs through holes in both sides of the carrier assembly. To the right of the shaft is a small bolt that screws into the carrier assembly and engages the end of the shaft. Place a large screwdriver between the differential housing and one of the bolts that holds the ring gear onto the carrier assembly. This is to prevent the carrier from turning when you remove the small bolt. Remove the bolt with a ratchet and socket.
5Rotate the carrier assembly 180 degrees until youre looking at the hole on the other side of the carrier assembly that holds the pinion shaft. Slide the shaft out of the carrier assembly in this direction. Pull the shaft out until the stepped part of the shaft contacts the ring gear.
6Push the outer end of the axle in toward the center of the differential housing. Move back under the Expedition; you will be able to see the end of the axle shaft. The axle shaft has a C-clip in a groove on the end of the axle. Use needle-nose pliers to carefully remove the clip. Remove the C-clip for the other axle in the same manner. Do not rotate the differential while the pinion shaft is pulled out. Slide the axles out of the end of the axle tubes.
7Attach an axle bearing puller to a slide hammer. Insert the bearing puller through the center of the bearing. Using the slide hammer, extract the bearing and oil seal. Repeat for the other bearing and oil seal. Clean the end of the axle tube with a shop rag. Note that there is a small step inside the axle tube that the axle bearing seats against.
8Tap the new bearing into the axle tube with a hammer and a socket the same size as the outside of the bearing. Seat the bearing against the step in the axle tube. Coat the rubber lip of the oil seal with gear oil. Use the same socket to tap the oil seal into the axle tube. Make sure the seal is flush with the end of the tube. Repeat for the other bearing and seal. Slide the axle into the axle tube far enough so you can reinstall the C-clip. After you install the clip, pull out on the axle to seat the clip in the recess in the small spider gear. Repeat for the other axle.
9Push the pinion shaft back through the carrier. Put a couple of drops of non-hardening thread sealer on the pinion shaft bolt, and reinstall the bolt. Torque the bolt to 20 foot-pounds with a torque wrench and socket.
10Coat the gasket mounting surface on the differential cover and the gasket mounting surface on the differential housing with gasket sealer. Coat one side of a new differential cover gasket with gasket sealer and press the gasket onto the differential cover. Coat the other side of the gasket with gasket sealer, and position the cover onto the housing. Install the bolts, and tighten them until the cover is just seated against the housing. Moving in a crisscross pattern, torque the bolts 30 foot-pounds.
11Remove the filler plug from the differential cover. Add 4 ounces of limited-slip friction modifier to the differential, then fill it with 75W-140 GL-5 synthetic gear oil. The differential is full when the gear oil reaches the bottom of the filler hole. Replace and tighten the filler plug.
12Install the brake drum, or install the rotor and rotate the caliper back onto the rotor. Torque the caliper mounting bolts to 30 foot-pounds. Mount the wheels, and install the lug nuts. Raise the Expedition and remove the jack stands. Lower the Expedition to the ground. Tighten the lug nuts. Test drive, and check for leaks.
Monday, November 18, 2013
Wheel Alignment Specifications for 1966 Chevy II Nova
Chevrolet introduced the Nova sports car in 1962. The alignment specs were the same for all trims of the 1966 Chevy Nova. The alignment was not adjustable on the rear end because the Nova came with a fixed rear axle.
Caster
The caster angle is the measurement, in degrees, of how far a line drawn through a wheels steering knuckle is inclined from a vertical line through the center of the wheel. The ideal caster for the 1966 Nova is +1.0 degree, but it can range from +0.5 to +1.5 degrees.
Camber
Camber is the angle at which the top of a wheel tilts when viewed from the front of the vehicle. Tilting out is positive camber, and tilting in is negative camber. The ideal camber for the 1966 Nova is +0.5 degrees, but it can range from zero to +1.0 degree.
Toe-In
Toe, when measured in inches, is the difference in the distances between the centers of the fronts and the rears of the front wheels. Most vehicles are designed to toe-in, meaning the distance between the fronts of the two front wheels will be slightly less than that of the backs of the two front wheels. The toe-in for the 1966 Nova can range from 1/4 of an inch to 3/8 of an inch.
Monday, November 11, 2013
How to Switch a 1986 Ford F150 4X4 Into Four Wheel Drive
The 1986 Ford F150 shipped from the factory with two four-wheel drive hub options; automatic locking hubs and manual locking hubs. With manual locking hubs, you need to get out of the vehicle and manually lock the front hubs before the truck will engage the four-wheel drive. With automatic locking hubs, all you need to do is engage the four-wheel drive with a lever and they will automatically lock within a few revolutions of the front wheels. While automatic locking hubs are a nice feature, some owners actually prefer the manual locking hubs because they are less prone to malfunctioning due to their simpler design.
Instructions
- 1
Stop the truck shift it into park, or first gear for trucks equipped with a manual transmission. Apply the parking brake.
2Exit the truck and rotate the locking switch at the center of the wheel hubs to the lock position. If your truck doesnt have these switches, then you have automatic locking hubs and can skip this step.
3Shift the transmission into neutral. Move the four wheel drive selector lever to the left, then down into your desired four wheel drive range. Use 4-LOW for low speeds below 15 miles per hour and increased torque. Use 4-HI for driving at road and highway speeds.
4Shift the transmission back into drive, or first gear for trucks with a manual transmission. Release the parking brake, then drive forward 20 to 25 feet to engage the four-wheel drive hubs.
Friday, November 1, 2013
Types of Wheel Nuts
Wheel nuts, or lug nuts, come in a variety of sizes and styles. The wheel nuts hold the tire in place, so the differences are mainly aesthetic. Lug nuts are not all the same size or style. Foreign vehicles tend to use ball-seat lug nuts, while domestic models use tapered-seat nuts. Some vehicles use a mag lug nut to properly center a rim.
Tapered
The most common lug nut is the tapered lug nut, also known as the acorn or or bulge lug nut due to the appearance of a bulge near the rim. The tapered nut is available in multiple thread patterns and diameters to fit almost any vehicle. The majority of trucks and domestic-made cars use tapered lug nuts. Hub-centric rims, or rims that are centered on the axle through the center hole on the rim, will use this style for a more secure fit. Factory-installed tapered lug nuts are commonly capped with chrome overlays that require care when removing or installing. Replacements that are chromed without capping are available at any auto parts retailer.
Ball Seat
Most imports use a ball-seat lug nut. The operation of the lug nut is the same as the tapered variety. The unit is characterized by a rounded connection to the rim. These are available in open-ended or closed-ended variations for use on rims with or without hubcaps. After-market auto parts offer the ball-seat lug nuts in a variety of colors and finishes to complement the vehicle and rims. The ball-seat is a contemporary style but not as common as the tapered lug nut.
Mag and Screw-in Varieties
Mag nuts resemble the screw-in variety of lug nuts found on some German-made cars, such as the Volkswagen and Mercedes. The screw-in variety uses a bolt that goes through the rim to fit into female connections on the rotor or hub. The bolt is capped with a conical or tapered head similar to the other variations. The mag lug nut penetrates the rim rather than pressing against the rim. The nut is characterized by a long-sleeve that fits into the holes on the rim. The mag nut is used on lugs that are too small for the standard rim.
Friday, October 18, 2013
How to Replace a Wheel Hub and How Tight to Tighten the Nut
The wheel hub houses the wheel bearings, which allow the wheels to turn smoothly, due in part to the large amount of grease packed in with the bearings. The wheel bearings support the weight of the vehicle and its load while minimizing the effort needed by the vehicle to perform its duties. The wheel hub also keeps all the parts of the wheel securely assembled and keeps the wheel securely attached to the vehicle.
Instructions
- 1
Loosen the lug nuts around the inner part of the hub cap using the appropriate socket but do not completely remove them. Use the jack to hoist up the vehicle and return to the lug nuts and remove them, setting them in a safe place. Remove the wheel and place out of the way. Using a screwdriver and hammer, tap at the dust cap to remove it and set it aside in a safe place.
2Remove the two caliper bolts, taking care not to allow the brake caliper to dangle by the brake line. Untwist the wire clothes hanger and create a temporary loop to hold the brake caliper in place, attaching to the vehicle or something nearby that can support the brake caliper without pulling on the brake line.
3Remove the retaining screw at the center of the wheel hub and then remove the center hub. With a screwdriver and hammer, carefully knock the notch at the edge of the axle nut and use the appropriate axle nut socket and breaker bar to remove the axle nut. This will require some force as it is attached with 200 ft.-lbs. torque. When the axle nut has been removed, grip the bearings with a rag (to protect fingers and buffer against the grease) and pull with even pressure to slide off. Remove the brake shield, if desired, and clean it.
4Use the three-jaw puller to remove the inner bearing race. Knock the inner dust shield out. Take the old parts and set them aside to be properly disposed of. Get the new parts ready to be placed on the vehicle.
5Replace the brake shield, once it has been cleaned if this was done, and place the inner dust shield properly in its spot, pushing it into place by hand and gently tapping with a tool, if needed, to ensure it is in properly. With gloved hands, apply a generous amount of automotive grease to the axle to protect against rust and damage.
6Take the new hub bearing, check to ensure there is sufficient grease on it and adding more if needed, and carefully slide it into place. Use a bearing installer to secure it. Replace the axle nut, using the appropriate axle nut socket and breaker bar to apply 200 ft.-lbs. of torque. Using a screwdriver and hammer, notch or dent the outer portion of the axle nut. Install the dust cap but check the wheel hub by spinning it a few times to ensure there are no metal-on-metal sounds or other inappropriate noises coming from the motion of the spinning.
7Replace the wheel and tighten the lugs to 85 ft.-lbs. of torque, using the appropriate socket size. Replace the hub cap, if any. Lower the vehicle from the jack and dispose of all old parts properly.
Wednesday, October 16, 2013
2001 Chevy Malibu Wheel Alignment Specs
The 2001 Chevrolet Malibu was a four-door sedan with a maximum horsepower of 170 hp at 5200 rpm. The car takes P215/60R15 tires. You should rotate your tires to prevent uneven wear. This helps you get more mileage out of the tires. After rotating or changing tires, you should align your vehicle for better steering and handling.
Camber Angles
The camber angles in both the front and rear should ideally be -0.2. However, they can be aligned anywhere between -0.5 degrees and 0.5 degrees.
Caster Angle
The caster angle on the 2001 Malibu can be from 3.1 to 5.1 degrees. The optimal alignment is at 4.1 degrees.
Toe-In Alignment
The toe-in angle should be in the -0.15 to 0.35 degree range. Ideally, it should be at 0.1 degrees. In the rear, the toe-in angle should be between -0.26 and 0.14 degrees. The optimal toe-out angle is 0.06 degrees.
Ride Height
After aligning the tires, check the ride height of the 2001 Malibu. Ride height is also known as ground clearance. The distance between the center of the front axle to the ground should be 32.2 inches. The bottom of the rocker panel should be 9.33 inches off the ground. The distance between the bottom of the ball joint and the bottom of the frame rail should be zero inches. The center of the rear axle should be 25 inches from the ground.
Saturday, September 28, 2013
How to Remove the Steering Wheel on a 65 66 Mustang
Ford released the Mustang late in the 1964 model year. The 1965 model year brought about the elimination of the 260-cubic-inch V-8 engine in favor of the 289-cubic-inch V-8, which had 36 more horsepower. The 1966 model year brought few changes to the Mustang. The most famous change was the addition of the "floating horse" to the grille. Replacing the steering wheel on 1995 and 1966 Mustang is a fairly straightforward process.
Instructions
- 1
Disconnect the negative battery cable from the battery, using a combination wrench.
2Rotate the horn button assembly -- horn button and three chrome arms in the center of the steering wheel -- counterclockwise to unlock it and pull the button assembly from the steering wheel. Make certain to catch the horn spring if it pops out.
3Remove the steering wheel retaining nut, using a ratchet and a 15/16-inch socket.
4Draw a matchmark line on the steering wheel and the shaft it mounts onto, using white marking paint. This allows for correct alignment of the steering wheel when reinstalling it.
5Install a steering wheel puller on the steering wheel and use the puller to free the steering wheel from the column. The exact instruction for the use of the steering wheel puller depends on the type of puller, so refer to the pullers instruction for specific details.
6Pull the steering wheel off the column slowly, as to not disturb any components in the steering column. Remove the steering wheel puller once the steering wheel is off the column.
7Draw a matchmark line on the new steering wheel, if applicable, as closely to the line on the old steering wheel as possible.
8Position the steering wheel so the lines match, and push the steering wheel onto the shaft. Tighten the steering wheel retaining nut to 20 to 30 foot-pounds, using a torque wrench and a 15/16-inch socket.
9Set the horn spring behind the horn button. Set the horn button assembly back on the center of the steering wheel and rotate it clockwise to lock it in place.
10Reinstall the negative battery cable and tighten it to 11 foot-pounds, using a torque wrench and socket.
Wednesday, September 18, 2013
Car Alloy Wheel Repair
Repairs to your cars alloy wheels can cost hundreds of dollars if you have them done in a garage, and they can leave you without wheels while they are getting repaired. You can repair scuffs, dents and scratches yourself if you have a modicum of previous knowledge about car maintenance. The work can be quite challenging; so if you find yourself struggling, ask for some help from someone who has experience with wheel refinishing.
Instructions
- 1
Apply some paint thinner to the rag, and scrub the entire alloy wheel to remove any buildup or dirt and debris.
2Put a small amount of auto-body repair filler putty on a putty knife, then fill all of the damaged areas on the alloy wheel. Allow the filler to fully dry before gently sanding off any excess filler with a small sander. You can get filler putty and a putty knife from most hardware stores.
3Apply masking tape on the areas of the alloy that you do not want paint applied to. Masking tape will help prevent paint leaks from getting on other areas of the alloy wheel and tire.
4Spray the alloy wheel with the primer, making sure to give it a thorough coat over the recently repaired areas. Allow the primer to fully dry before applying a second coat of primer spray. Remove all of the masking tape after allowing the second coat to dry. Spray a tiny amount of primer over the obvious primer edges revealed when you removed the masking tape.
5Apply more masking tape to the tire to protect the areas you dont want paint applied to. Spray a thin layer of your chosen color over the alloy. A thin layer will help prevent the paint from running. Apply a second coat once the first coat has dried. Remove the masking tape once finished.
6Wipe over the alloy with a rag to remove any dirt or dust left on the alloy wheel.
Tuesday, September 17, 2013
DIY Wheel Bearings for a Utility Trailer
Utility trailers are simple vehicles for light hauling and need little maintenance. Still, they do have some items that need to be checked and serviced regularly. The tires should be checked for air pressure and for damage before each trip. Also, the wheel bearings need to be serviced at least once a year. The wheel bearings on utility trailers are separate from the hub and can be serviced and replaced separately. This can be done with basic tools in a couple of hours on a two-axle trailer.
Instructions
Removal
- 1
Raise the trailer with a jack and support it on jack stands. Remove the center dust cap from the hub with a screwdriver. Remove the cotter pin from the castle nut inside the cap with a pair of pliers.
2Grasp the wheel from the top and bottom and pull out. The outer bearing will pop out. Remove it and set it aside. Set the wheel on the ground face up.
3Tap out the inner bearing and seal with a non-metallic object to prevent damage to the bearing races. A block of wood works great for this. Set the inner bearing aside, keeping it separate from the outer bearing.
Cleaning, Inspection and Installation
- 4
Spray shop solvent on both bearings and inside of the hub. Wipe away all of the grease with a shop rag. Inspect both bearings and their contact surface. They should be free of pits and roll smoothly. If not, replace them.
5Place a lump of grease in the palm of your hand and work the inner and outer bearing into the grease, forcing it thoroughly inside all of the rollers.
6Insert the inner bearing into the hub. Tap in a new grease seal with the hammer and block of wood to prevent damage. Place the wheel and hub onto the spindle of the trailer. Place the outer bearing onto the spindle, pushing it inside the hub. Replace the washer and castle nut.
7Tighten the castle nut firmly as you spin the wheel then back off the castle nut by 1/8 of a turn. Insert a new cotter pin through the hole in the spindle and the castle nut. Replace the dust cover. Repeat for the other wheels on the trailer.