Wednesday, April 30, 2014
How to Remove a Spline Nut on a 1999 Oldsmobile Alero
The spline nut, also known as the axle spline nut or axle nut, is located on the threaded end of each front axle shaft. This nut holds the splined end of the axle securely inside the wheel hub. The axle nut is a 34 mm nut that is pinched in order to prevent it from loosening. Because the nut is pinched in the manufacturing process, it is not reusable. There are two types of axle nuts installed on 1999 Aleros, and both are not reusable. The first type is the older style that is black with a sheet metal cage around the nut. The new nut is a silver-colored, standard-size pinch nut. If your vehicle has the old style nut, it must be removed and replaced with the new style nut. If your vehicle has the new style nut, it must be replaced when removed with a new nut of the same style.
Instructions
Removal
- 1
Apply the parking brake and chock the rear wheels. Break the front lug nuts loose with a lug nut wrench. Raise the vehicle with a jack and slide jack stands under the frame. Lower the vehicle onto the jack stands and make sure that its secure.
2Remove the lug nuts completely, then remove the tire. Have an assistant depress the brake pedal. Attach a 34 mm socket to a T-handle bar and break the axle nut loose while your assistant is holding the brake pedal; this will prevent the wheel and hub from turning while you break the nut loose.
3Remove the axle nut the rest of the way using a 1/2-inch ratchet and your 34 mm socket. Throw away the old nut; it cannot be reused.
Installation
- 4
Thread the new nut onto the spindle by hand, then have an assistant depress the brake pedal once again.
5Tighten the nut to 173 foot-pounds with a torque wrench. Reinstall the tire and snug the lug nuts with a lug nut wrench.
6Lower the Alero back to the ground and torque the lug nuts in a criss-cross pattern to 100 foot-pounds with a torque wrench.
Friday, October 18, 2013
How to Replace a Wheel Hub and How Tight to Tighten the Nut
The wheel hub houses the wheel bearings, which allow the wheels to turn smoothly, due in part to the large amount of grease packed in with the bearings. The wheel bearings support the weight of the vehicle and its load while minimizing the effort needed by the vehicle to perform its duties. The wheel hub also keeps all the parts of the wheel securely assembled and keeps the wheel securely attached to the vehicle.
Instructions
- 1
Loosen the lug nuts around the inner part of the hub cap using the appropriate socket but do not completely remove them. Use the jack to hoist up the vehicle and return to the lug nuts and remove them, setting them in a safe place. Remove the wheel and place out of the way. Using a screwdriver and hammer, tap at the dust cap to remove it and set it aside in a safe place.
2Remove the two caliper bolts, taking care not to allow the brake caliper to dangle by the brake line. Untwist the wire clothes hanger and create a temporary loop to hold the brake caliper in place, attaching to the vehicle or something nearby that can support the brake caliper without pulling on the brake line.
3Remove the retaining screw at the center of the wheel hub and then remove the center hub. With a screwdriver and hammer, carefully knock the notch at the edge of the axle nut and use the appropriate axle nut socket and breaker bar to remove the axle nut. This will require some force as it is attached with 200 ft.-lbs. torque. When the axle nut has been removed, grip the bearings with a rag (to protect fingers and buffer against the grease) and pull with even pressure to slide off. Remove the brake shield, if desired, and clean it.
4Use the three-jaw puller to remove the inner bearing race. Knock the inner dust shield out. Take the old parts and set them aside to be properly disposed of. Get the new parts ready to be placed on the vehicle.
5Replace the brake shield, once it has been cleaned if this was done, and place the inner dust shield properly in its spot, pushing it into place by hand and gently tapping with a tool, if needed, to ensure it is in properly. With gloved hands, apply a generous amount of automotive grease to the axle to protect against rust and damage.
6Take the new hub bearing, check to ensure there is sufficient grease on it and adding more if needed, and carefully slide it into place. Use a bearing installer to secure it. Replace the axle nut, using the appropriate axle nut socket and breaker bar to apply 200 ft.-lbs. of torque. Using a screwdriver and hammer, notch or dent the outer portion of the axle nut. Install the dust cap but check the wheel hub by spinning it a few times to ensure there are no metal-on-metal sounds or other inappropriate noises coming from the motion of the spinning.
7Replace the wheel and tighten the lugs to 85 ft.-lbs. of torque, using the appropriate socket size. Replace the hub cap, if any. Lower the vehicle from the jack and dispose of all old parts properly.
Saturday, September 14, 2013
Lug Nut Problems
Every vehicle, from a passenger car to a large semi-truck, uses lug nuts. But, when the wheels have a problem, the lug nuts are among the first thing to be checked and adjusted.
Identification
Lug nuts are the large, threaded covers that hold each vehicle wheel to the axle. Depending on the vehicles manufacturer, there can be four to six lug nuts for each wheel.
Considerations
A loose lug nut can result in a wobbling wheel. Tire tread and balance of the wheel is compromised if the lug nut is loose. Verify the proper torque of the lug nuts in the owners manual or with a dealer.
Significance
Lug nuts can be over-torqued as well. If they are too tight, they can warp the brake rotor or break the studs, leading to a costly repair. Lubrication should not be applied to lug nuts or their studs to prevent improper torque.