Monday, January 20, 2014
How to Replace a Key for a 2005 Honda Pilot
The 2005 Honda Pilot comes with special keys that include a built-in key fob for remotely locking and unlocking the vehicle. To work properly, each key fob has to be programmed to match a unique vehicle. The key part must be custom cut by a locksmith or dealer as the cutting is not the same as older Hondas and cant be cut by a traditional key-cutting machine. Blank Pilot keys are available through dealers or some auto parts suppliers.
Instructions
Replacing the Key Through a Dealership
- 1
Contact a Honda dealership parts department and ask for a replacement key.
2Provide to the dealership the Vehicle Identification Number (VIN) and proof of ownership. The dealership will cut and program the replacement key to work with your vehicle.
3Test the new key and fob to make sure it works properly with your Pilot.
Replacing the Key Through an Auto Parts Supplier
- 4
Purchase a replacement key from a parts supplier. Make sure the supplier provides programming instructions with the key in case the key has any nonstandard programming steps. If they do not, check the programming link in the article resources for instructions. The instructions are for a 2008 Pilot, but they should work for most Honda-compatible key fobs.
5Follow the directions provided with the key. The directions will vary based on the key manufacturer. The directions will only be for programming the fob; the key will still need to be cut. Test the fob after programming to make sure it works with the Pilot.
6Take the key to an automotive locksmith that provides Honda key cutting or to a Honda dealership. Provide the VIN so the key can be cut to work with your Pilot. The key is cut based on the VIN. Locksmiths usually charge a lower fee than dealerships to stay competitive.
Sunday, January 19, 2014
How to Replace a Starter on a 1987 Honda Prelude
The 1987 Honda Prelude might have a direct-drive starter or a gear reduction starter mounted to the engine. Regardless of the starter mounted on your Prelude, the differences are internal and the process for removing and replacing the starter remains the same. A starter turns the flywheel when you turn the cars key, and this helps your engine to start. When the starter fails, your Prelude will not start.
Instructions
- 1
Disconnect both battery terminals, starting with the negative terminal. Use a wrench to loosen the nut on the clamp, and pull the terminal off the battery.
2Disconnect the large black and white cable form the starter motor by pulling it off the connector.
3Remove the nut that holds the starter wire onto the starter solenoid. On the Honda Prelude, the solenoid bolts to the right side of the starter. The wire bolts to the top right of the solenoid on the gear reduction starters and on the bottom right on the direct drive starters. Use a wrench to remove the nut, then pull the wire off the solenoid.
4Remove the engine wiring harness from the starter. Certain engine and transmission combinations have a clip that holds the engines harness onto the starter. If equipped, remove the harness from the clip.
5Remove the two bolts that hold the starter onto the engine with a wrench, and remove the starter from the engine.
6Place the new starter against the engine, and tighten both bolts to 32 foot-pounds with a torque wrench.
7Reconnect the engine wire harness to the clip on the starter, if equipped. Plug the black and white wire into the starter motor, and secure the starter wire to the solenoid with the nut and wrench.
8Reconnect the battery terminals, starting with the positive terminal.
How to Replace the Headlamps on a Pontiac Grand Prix
Its important to replace your cars headlamp bulbs as soon as they stop working. Failure to do so can result in a ticket or, even worse, cause an accident. Replacing the headlamps on a Pontiac Grand Prix may seem intimidating to those who have little or no experience working with vehicles, but the process is surprisingly straightforward.
Instructions
- 1
Open the vehicles hood and turn the engine off. Wearing protective gloves, locate the metal retaining clip above the headlight and use a socket wrench to remove the bolt.
2Pull up on the retaining clip while pushing back on the headlamp and align the marking on the retaining clip with the notch on the headlamp. Pull the headlamp assembly out of the vehicle.
3Remove the bulb socket ring from the headlamp assembly by turning the ring counterclockwise. Pull the old bulb out from the socket and place the new bulb in.
4Reinstall the bulb socket ring by placing it back onto the headlamp assembly and rotating it clockwise. Place the headlamp assembly back into the vehicle.
5Push down on the retaining clip while at the same time pushing back on the headlamp to ensure that the headlamp assembly is secured into place. Place the bolt back into its initial position and securely tighten it.
Saturday, January 18, 2014
How to Install Distributor Cap for 1991 Honda Accord
The distributor cap is the cover that protects the distributor and provides a spot for each spark plug wire coming from each spark plug in the cylinders. The distributor spins underneath the cap, sending a bolt of electricity to each point on the distributor cap. The electricity then travels through the wires to the spark plugs. In the 1991 Accord, the distributor is a round shape and has four spots for spark plug wires, since it came with a standard four-cylinder engine.
Instructions
- 1
Prepare the old distributor cap for removal by unplugging the 2-P and 8-P connectors connected to it. Unplug the two hoses going to the advance diaphragm if your Honda Accord uses a carburetor instead of fuel injection. Loosen the three hold-down bolts on the distributor cap, leaving the spark plug wires plugged into it.
2Coat the O-ring from the new distributor cap with motor oil using your finger. This is done so that the ring goes in smoothly and doesnt tear from friction.
3Take the old distributor cap off of the cylinder head, and slide the new distributor cap on in its place. Make sure that the three hold-down bolts are lined up with their respective holes.
4Unplug the spark plug wires from the old distributor cap, and plug them into the new distributor cap using the same position. If your wires are already unplugged, plug the wire coming from cylinder 1 into the spot marked with an "A" on the distributor cap. From there, proceed clockwise plugging in the wires from cylinders 3, 4, and 2 in that order.
5Tighten the hold-down bolts, and reconnect the 2-P and 8-P connectors to the distributor cap. Make sure the two vacuum hoses going to the advance diaphragm are also plugged in to complete the installation. If you need to, you can test and adjust the timing of the motor before tightening the hold-down bolts on the distributor cap.
Special Chrysler Tools
The Chrysler line of cars, and the company that makes them, was named for Walter Chrysler, who introduced the first Chrysler automobile in 1924. In its long history, Chrysler has produced millions of cars, trucks and vans, and several companies manufacture tools designed especially for Chrysler parts and products. The American automaker headquartered near Detroit was ranked the worlds thirteenth largest vehicle manufacturer in 2008, with a revenue of $17.7 million.
Axle Seal Installer
The Miller Special Tools Company manufactures and sells the Axle Seal Installer Chrysler Dana MLR-5041. The installer is used with the 5041 Seal Installer and 8417 Adapter. The tools are used to install the right and left inner seals into the axle tubes in Chrysler models built from 2000 through 2002. The models are built with 248FBI axles.
SPX Miller Special Tools, a 95-year manufacturer of automotive parts as of 2011, is the primary supplier of specialty tools to Chrysler LLC.
Oil Filter Wrench
Assenmacher makes an Oil Filter Wrench M0284 for use on Chryslers. The wrench is also compatible with 2007 Sprinter, Mercedes and Jeep vehicles with V6 diesel engines. The wrench is 84 mm with 14 flats, and 22 mm hexagonal end.
Assenmacher, an independent company based in Boulder, Colorado, sells specialty tool for Chrysler, as well as Toyota, and several other domestic, European and Asian manufacturers.
Ball Joint Separator
Miller Special Tools also manufactures the Ball Joint Separator 9282, item number MLR-9282, for Chrysler vehicles. The tool is used to separate the ball joint from the knuckle on the Dodge Sprinter.
Belt Tension Gauge
The Owatonna Tool Company makes the Belt Tension Gauge C-4188 for Chrysler vehicles. The gauge is used to test tension on timing and fan belts, and to accurately calibrate the belts. The gauge measures tension in units of newtons and pounds, from 30 pounds to 180 pounds (130 to 800 newtons). The company also makes the gauge for Ford, Rotunda, Hummer and General Motors. The Owatonna Tool Company, formed in 1925, is based in Owatonna, Minnesota, and is best known for its pullers and presses.
Belt Tension Socket Wrench
Kent-Moore builds a Belt Tension Socket Wrench for Chrysler vehicles. The wrench, part number 09244-28100, also works with the 1991 to 1995 Elantra, the 1991 to 1998 Sonata, the 2000 and newer XG300 and XG350, and the 2001 and newer Santa Fe. Kent-Moore is part of SPX Service Solutions, and manufactures tools for service professionals.
Friday, January 17, 2014
Instructions on Installing an Auxiliary Light Bar on a Harley Softail
Heritage Softails come equipped from the factory with a light bar. Well known aftermarket vendors like Kuryakyn and Harley-Davidson sell bolt-on auxiliary lighting for Softails. The extent to which extra lights brighten the road is open to debate. Many jurisdictions mandate that the extra light be turned off when the headlight is switched to high beam. But it is undeniable that the extra lights make the motorcycle brighter and make it, and the rider, easier to spot.
Instructions
EFI Fuel Tank Removal
- 1
Ride the motorcycle until the gas tank is almost empty.
2Pull off the electrical caddy cover, on the right side of the motorcycle, with your hands. Pull the fuel pump fuse out of the fuse array with a fuse puller.
3Run the engine until it dies. Push the starter button for another three or four seconds.
4Pull both ends of the quick connect fitting under the gas tank in opposite directions until the two halves of the fitting come apart.
5Loosen the screw that holds the rear fender and the seat together with a Phillips head screwdriver. Lift off the seat.
6Loosen the black battery cable with a combination wrench. Pull the cable from the negative terminal.
7Loosen and remove the nut in the middle of the instrument panel with an Allen socket and socket wrench. Pull the instrument panel up and pull the male and female halves of the fuel pump module connector apart.
8Plug the end of a short length of 5/16 inch diameter, rubber hose with a bolt of the same size. Secure the bolt in the hose with a hose clamp and a screwdriver.
9Place a 5 gallon gas can next to the motorcycle. Sever the clamp on either end of the crossover fuel line with metal shears.
10Pull the loose end of the crossover line off the tank fitting and immediately replace it the open end of the 5/16 inch hose. Drain the crossover line into the 5 gallon can.
11Clean up spillage with rags and remove the rags from the work location. Set the can aside.
12Unplug the crossover and vent lines from the bottom of the tank. Unbolt both the front and rear mounting bolts, washers and nuts with a combination wrench. Unplug the male and female halves of the fuel gauge wiring plug.
13Pull the tank off the motorcycle with your hands.
Auxiliary Lighting Installation
- 14
Attach the right and left light bar mounting clamps in the accessory lighting kit to the two fork tubes using the Allen screws in the kit and an Allen socket. Tighten both screws to 75 inch pounds of torque with the Allen socket and a torque wrench.
15Thread the wires from the accessory lights through the holes in the mounting brackets and fasten the lights to the brackets with the washers, retainers and clamp blocks included with the kit. Tighten the retainers of 19 pounds with an open end socket and torque wrench.
16Slip the inner nesting rings in the lighting kit onto the light bulbs in the kit. Lock the black wires to the black terminals next to the indexing tabs and the grey wires to the grey terminals.
17Install the accessory light bulbs into the chrome trim rings using the screws included with the kit and a screwdriver. Thread the light wires through the chrome tubes in the kit.
18Place the accessory lights wiring harness in the shallow pan that holds the seat. Stretch the longest wires along the backbone of the frame to the steering head.
19Remove the hex nut from the ground wire stud with a combination wrench. Slide the ground wire ring from the accessory lighting wiring harness onto the stud and replace the nut.
20Snap the white wiring harness connector into the "B" positive connector on the accessory lighting wire harness.
21Tie the accessory harness to the main wiring harness with the cable ties included with the accessory lighting kit.
22Stretch the longest wires in the auxiliary harness past the steering head. Route the light switch wires up the triple trees and across the left handlebar to the clutch lever cover.
23Disassemble the chrome, switch mounting bracket with a Torx driver, install the light switch and reassemble the mounting bracket.
24Remove the lower screw from the clutch lever housing with a Torx driver. Put the switch bracket tab over the hole and reinstall the screw. Tighten to 68 inch pounds using a torque wrench and Torx socket.
25Push the light switch wiring harness into the handlebar wiring retainers. Remove the trim ring from the headlight with a Phillips head screwdriver.
26Unplug the connector block from the headlight prongs. Unwrap the waterproof boot from the rear of the headlight.
27Squeeze and remove the retaining clip from the headlamp assembly. Twist the clip away from the headlamp and remove the headlamp bulb.
28Push the end of the light switch wire through the rubber ring in the headlight housing. Splice the switch wire to the yellow headlight wire using the crimp connecter in the lighting kit and a pair of pliers.
29Replace the headlight bulb in the headlight housing.
30Slip heat shrinkable tubing from the kit over the white wire in the accessory wiring harness. Strip the insulation from the end 1/4 inch of the two auxiliary lights power wires with a wire stripper.
31Splice all three wires with the three-way tube connector in the kit using a crimping tool. Cover the connector with the heat shrink tube and heat with a heat gun until the tube shrinks around the splice.
Final Assembly
- 32
Secure all loose wires with the clips included in the kit.
33Reattach the gas tank. Refuel the motorcycle.
34Reconnect the black battery cable. Replace the fuel pump fuse.
35Reattach the electrical caddy cover and seat.
How to Retrieve Codes for a Ford OBD 1
Fords manufactured before 1996 come equipped with a first-generation On-Board Diagnostics computer (OBD-I) that retrieves and stores all error codes sent to it from various sensors throughout the vehicle. When these sensors detect a malfunction, they send the trouble code to the Fords computer, which turns on the vehicles warning and service lights. You can pull these codes right at home using a small device known as an OBD-I code reader, which you can purchase at any auto-parts retailer.
Instructions
- 1
Locate the diagnostic port on the drivers-side dash near the steering column. The port will be the same size and shape as the connector end of the OBD-I code reader.
2Plug the code reader into the port.
3Put the key into the ignition and turn it to the "II" position, but dont crank the engine.
4Wait for the code reader to power on. Some readers have to be turned on, so you may have to find the "on/off" switch.
5Select the command on the reader that says "Retrieve Codes" or something similar (the command will vary by brand). Wait while the code reader interfaces with the vehicles computer, then write the codes down on a piece of paper.
6Look up the codes in the scanner manual. Unplug the reader and have the vehicle serviced or repaired based on the diagnosis obtained from the codes you retrieved.