Pages

Showing posts with label starter. Show all posts
Showing posts with label starter. Show all posts

Thursday, September 4, 2014

How to Replace the Starter on a 2002 Camry

How to Replace the Starter on a 2002 Camry

The starter on the 2002 Toyota Camry is a cylindrical piece located on the lower part of the engine on the drivers side of the vehicle. Its positioned between the transmission and transmission cross member and is bolted to the bell housing. The starter is responsible for the initial cranking power needed to turn the engines pistons.

Instructions

    1

    Remove the negative battery cable connector from the battery with a crescent wrench. This cuts off power to the Camrys starter.

    2

    Remove the wiring harness from the starter solenoid by pulling the wire connector off the male connector on the solenoid.

    3

    Disconnect the black grounding wire from the side of the starter by removing the bolt with a crescent wrench.

    4

    Remove the three bolts that secure the starter to the bell housing with a 9/16 socket.

    5

    Pull the old starter out of the bell housing and then place the new starter into the bell housing.

    6

    Bolt the starter in place.

    7

    Reconnect the ground wire to the side of the Camrys starter.

    8

    Reconnect the starter solenoid wiring harness.

    9

    Reconnect the negative battery cable.

ReadMore

Sunday, January 19, 2014

How to Replace a Starter on a 1987 Honda Prelude

The 1987 Honda Prelude might have a direct-drive starter or a gear reduction starter mounted to the engine. Regardless of the starter mounted on your Prelude, the differences are internal and the process for removing and replacing the starter remains the same. A starter turns the flywheel when you turn the cars key, and this helps your engine to start. When the starter fails, your Prelude will not start.

Instructions

    1

    Disconnect both battery terminals, starting with the negative terminal. Use a wrench to loosen the nut on the clamp, and pull the terminal off the battery.

    2

    Disconnect the large black and white cable form the starter motor by pulling it off the connector.

    3

    Remove the nut that holds the starter wire onto the starter solenoid. On the Honda Prelude, the solenoid bolts to the right side of the starter. The wire bolts to the top right of the solenoid on the gear reduction starters and on the bottom right on the direct drive starters. Use a wrench to remove the nut, then pull the wire off the solenoid.

    4

    Remove the engine wiring harness from the starter. Certain engine and transmission combinations have a clip that holds the engines harness onto the starter. If equipped, remove the harness from the clip.

    5

    Remove the two bolts that hold the starter onto the engine with a wrench, and remove the starter from the engine.

    6

    Place the new starter against the engine, and tighten both bolts to 32 foot-pounds with a torque wrench.

    7

    Reconnect the engine wire harness to the clip on the starter, if equipped. Plug the black and white wire into the starter motor, and secure the starter wire to the solenoid with the nut and wrench.

    8

    Reconnect the battery terminals, starting with the positive terminal.

ReadMore

Tuesday, November 5, 2013

Troubleshooting Starter Problems with the VW Passat

Troubleshooting Starter Problems with the VW Passat

The VW Passat is a four-door sedan that comes with a manual or automatic transmission. If your VW Passat will not start properly, it might be a problem with the starter. The starter on your Passat sends an electrical signal from the battery to the engine when the key is engaged in the ignition. You can test the starter with minimal automotive knowledge and little hassle.

Instructions

    1

    Park your VW Passat on a flat surface. Engage the emergency brake to secure the car from rolling. Make a note of the security code for your Passats radio. You can find this in the owners manual.

    2

    Open the hood and use a wrench to disconnect the black cable from the battery on the right side of the engine. Go under the car and check for the engine shield. Use a wrench to remove the shield if your car has one (some models do not use an engine shield).

    3

    Pull the shield out from under the car and locate the starter. The starter is located on the right side of the engines bottom. Disconnect the red cable from the car battery, then connect the red and black leads from your voltmeter to the starters red and black wires going to the battery.

    4

    Look at the instrument display for a reading. If you do not get a 12-volt reading, you either need to replace the starter or the battery. Test the battery terminals with your voltmeter and replace the battery if needed.

ReadMore

Saturday, September 28, 2013

Auto Starter Information

Auto Starter Information

Because an auto starter is responsible for cranking your engine, failure of this part can leave you without transportation. Current draw, testing methods and other helpful tips can all be beneficial auto starter information.

Current Draw

    The amount of current that a starter pulls varies depending on its type. A well working starter can draw up to 150 amps while cranking a vehicle with a four-cylinder engine. In bigger vehicles with V8 engines, starters can draw over 200 amps during cranking.

Testing

    Using a battery, jumper cables, and a large sized bench vice to secure it, you can test a starter after removing it from the vehicle. By connecting the starter to the battery with jumper cables, you can study the speed at which the starters motor spins to determine if its spinning too slow and needs replacing.

Tips

    Starters are often wrongly suspected to be the cause of engines that fail to start. To avoid purchasing a new starter when you dont need it, you should make certain other checks first, such as on the battery. Voltage tests on the battery will sometimes reveal that it is lacking the needed voltage to power up your starter.

ReadMore

Tuesday, September 10, 2013

How to Charge a Battery Jump Starter

How to Charge a Battery Jump Starter

A portable vehicle jump starting device can be handy if your car has a dead battery. However, the jump starter wont do much good if it, too, is dead. Fortunately, most vehicle battery jump starters, sometimes referred to as battery chargers, come with several options to keep them charged. How you charge your specific battery jump starter will depend on the brand and item you purchased.

Instructions

    1

    Plug the battery jump starter into a regular wall outlet. Many car battery jump starters and chargers have standard plugs that can connect them to an electrical outlet. These batteries charge using electricity, so the process is similar to plugging your cell phone into its wall-charger.

    2

    Use your vehicles A/C adapter. You can charge many car battery jump starters by attaching them to the the A/C adapter (cigarette lighter) on your vehicle. Similar to charging a cell phone in a car, the jump starter can draw enough power from your A/C outlet to keep a full charge and will be ready when you need it.

    3

    Use solar power. Though they are not very common, there are solar-powered car battery chargers that can be used to power your car battery jump starter. These are not typically portable, but they do work for stationary battery charging and jumping.

ReadMore