Pages

Friday, February 28, 2014

How to Change the Valve Body in a 1994 Ford Bronco Transmission

Changing the valve body in your 1994 Ford Bronco with automatic transmission can give you more control over the shift points of your transmission as well as fix valve body-related transmission problems. With the right tools, this is a job that can be accomplished in around three to four hours.

Instructions

    1

    Place wheel chocks in front of and behind one rear wheel. These can be 4-by-4-in. blocks. Jack the front end of the Bronco up enough that you can comfortably slide under the transmission area. Place the jackstands under both sides and caully lower the vehicle onto them.

    2

    Push the drain pan with the umbrella over it under the rear portion of the transmission where you can reach it from under the transmission pan. Bringing the tools, slide under the truck inline with the transmission pan.

    3

    Verify the correct socket size for the transmission pan bolts. Attach the correct socket to the end of the extension and the extension to the ratchet. It will be either the 7/16 or 1/2-in. socket.

    4

    Remove the three bolts from one corner by rotating them counterclockwise. Loosen the rest of the pan bolts halfway.

    5

    Slide the drain pan and umbrella under the transmission pan.

    6

    Insert the tip of the screwdriver between the pan and transmission case in the corner with the removed bolts and twist, breaking the seal of the gasket. Hold the pan umbrella and center the drain pan under the fluid flow. Wait for the flow to significantly slacken.

    7

    Remove the remaining bolts, slowly allowing the rest of the transmission fluid to flow out of the pan. Set the pan aside.

    8

    Remove the three screws holding the transmission filter in place and remove the filter, setting it into the pan umbrella.

    9

    Verify the size of the bolts securing the valve body and attach the correct socket to the extension. Rotate the bolts counter-clockwise to remove them. Set the bolts aside within easy reach. Set the valve body in the umbrella also.

    10

    Slide out from under the truck and clean the transmission pan with the parts cleaner and rags. Use the scraper to remove the gasket and through this away. Slide the pan and replacement parts and scraper under the truck and caully remove the drain pan.

    11

    Slide under the truck and use the gasket scraper to remove the gasket from the transmission case to pan mating surface.

    12

    Align the new valve body correctly and insert the bolts into the corresponding holes and start them by twisting them clockwise.

    13

    Attach the socket and ratchet to each bolt and tighten them to approximately 30 pounds per square inch of torque.

    14

    Align the new transmission with the bolts and fluid holes and insert the three retaining bolts. Twist these clockwise to start and tighten with the screwdriver.

    15

    Align the pan gasket with the bolt holes in the transmission pan. Use four to six bolts to hold the gasket in place and place the gasket and pan against the transmission case. Start the four or six bolts sufficiently to hold the pan in place by turning them clockwise.

    16

    Insert and start the remaining bolts. Run them all down to finger tight.

    17

    Tighten the bolts, moving from the center of each side of the pan to the corners. Torque the bolts to between 30 and 40 foot-pounds of torque. Slide out, bringing the tools with you.

    18

    Lift the truck off the jack stands and pull them out. Slowly lower the truck completely and pull the jack out.

    19

    Remove the transmission dipstick and insert the funnel in the opening. Caully pour four to five quarts in. Start the engine and allow the transmission to warm up. Shift gears every 10 to 15 seconds.

    20

    Place the transmission in park and check the fluid level. Pour enough fluid in for the reading to be full. Shift gears every minute or so again to ensure proper fluid flow.

ReadMore

The Air Conditioning Specifications for a 1999 Lexus LS400

If your air conditioning malfunctions in your 1999 Lexus LS400, prompt servicing is the best way to protect your Lexus investment. Any automotive mechanic can recharge your air conditioner, but damage to your air conditioning system requires Lexus service technicians, certified by the Lexus Commitment to Excellence program, if you want your warranty to stand. Mechanical or electrical air conditioning problems may mean replacing the entire system, the compressor, condenser, accumulator, evaporator, blower motor, control unit, fan and clutch.

Compressor Specifications

    The Lexus Part Store sells new and urbished used air conditioner compressors for the 1999 Lexus LS400. The remanufactured compressors come with a core charge. The LS400 compressor has six grooves, a 1.65-inch line, a mount manifold, a tangent mount, a 4.5-inch pulley, a speed sensor switch and a clutch. The urbished compressor carries a two-year or 24,000-mile warranty. The new compressor cost $442 in 2010 and is under warranty for one year. The urbished compressor cost $395 in 2010. A core charge of $61 in 2010 was imposed on top of the part cost; the core charge is unded to the purchaser upon receipt of the old compressor.

Condenser Function

    The condenser collects filth and oil from the compressor. Refrigerant may carry this filth through the condenser to the expansion valve, clogging the valve or tube. If oil cannot flow through the condenser, the compressor cannot receive oil, and the compressor will lack lubrication. If the condenser is dirty, it may be necessary to replace it. Flushing the compressor definitely moves sludge through the system. The sludge may form a blockage or damage the compressor. If you damage your air conditioner by flushing it, your warranty will be void, at least for the air conditioner.

Condenser Specifications

    The Lexus Parts Store website lists two condensers for a 1999 Lexus LS400. A new first-class condenser with a clutch, manufactured from high-quality materials for extended reliability, cost $235 in 2010. A limited 1-year warranty covers manufacturers defects in the compressor. A second aluminum parallel flow condenser cost $139 in 2010. It is guaranteed to fit without leaking. Both condensers reduce noise and vibration. A chrome-plated compressor gasket or trim ring fits most cars and trucks with 7-inch radial compressors. The gasket costs $29 from the Lexus Parts Store in 2010 and comes with a 90-day warranty.

ReadMore

Thursday, February 27, 2014

Does the 2001 Kia Optima Have a Transmission Filter

Proving yet again that the only bad question is the one not asked, heres one with a few different answers. They all involve a "yes," but with a few provisos -- primarily in terms of filter location. The Optimas automatic transmission underwent a few changes in the middle of the 2001 model year that determine where youll find the filter and how youll go about changing it.

Filter Locations

    According to Kia technical service bulletin TT651003-005 -- published in the wildly popular Kia Technician Times, Volume 6, Issue 5, 2003 -- the company switched from external to internal transmissions in the middle of the 2001 model year. This goes for both 2.4-liter four-cylinder and 2.5-liter V-6 engines. Check the VIN number and the exact production date of your Optima; cars produced from October 1st, 2000 to December 31st, 2001 used transmissions with an external filter, while later models used an internal one.

A Cause for Change

    External filters are a nice touch when it comes to maintenance, but theyre uncommon for one primary reason. If youve ever been under your car, youll notice that Kia left just about enough room for a snake to slither through. While this wasnt anything that Kias engineers couldnt deal with, this particular transmission also saw use in the same-year Sonata, Santa Fe and Trajet; and, Kia being Kia, also likely had designs on selling the design after its production cycle to another manufacturer. So, out went the external filter, and in comes the internal one.

Replacing the External Filter

    The external filter is great from a maintenance point of view. It screws onto the the transmission case just above the transmission fluid oil pan and should be clearly visible from the bottom of the car. You should be able to get to it from the top after removing the air cleaner assembly. After removing the old filter with a filter wrench, clean the mating surface and the surrounding area, lubricate the O-ring on the filter and tighten it to 8 or 9 foot-pounds.

Replacing the Internal Filter

    Internal filter transmissions are more compact by nature, but changing the filter is a comparative pain. But little more so than any other car. Slide under the car and remove the 10 millimeter transmission pan bolts, starting at one side and working toward the other. Be prepared for transmission fluid to cascade out of the top of the pan. Scrape any gasket material off of the transmission and oil pan. Youll find the filter secured to the bottom of the transmission, inside the pan, by three bolts. Remove them, replace the filter, and reinstall the pan. Tighten all of the bolts to about 10 foot-pounds and ill the transmission with 3.5 quarts of SP3 transmission fluid.

ReadMore

How to Change Fuel Injectors on a 1994 Nissan Maxima

The Nissan Maxima is a mid-size car manufactured by Nissan since 1976. The third generation of this vehicle was in production from 1989 to 1994 and represented a major redesign. All versions of the 1994 Nissan Maxima have a 6-cylinder 3.0-liter engine with sequential fuel injection. The fuel injectors are on top of the engine and their replacement also requires you to remove the fuel rails.

Instructions

    1

    Disconnect the negative battery cable with a socket wrench to prevent the battery from producing sparks. Remove the collector for the intake manifold. Detach the hoses on the fuel pressure regulator and fuel rails.

    2

    Detach the electrical connectors for the fuel injector and disconnect the mounting bolts for the fuel rail with a socket wrench. Lift the fuel rail assembly from the engine.

    3

    Remove the retainer screws for the fuel injector with a socket wrench and press the fuel injector from the fuel rail. Discard the O-rings for the fuel injector and apply a thin layer of engine oil to the new O-rings.

    4

    Install the O-rings to the new fuel injector and press the fuel injector into the fuel rail. Fasten the retainer screws for the fuel injector with a socket wrench.

    5

    Place the fuel rail assembly onto the engine. Torque the fuel rail mounting bolts to between 6.9 and 8.0 ft. lbs. with a socket wrench, then torque them to between 15 and 20 ft.lbs.

    6

    Attach the fuel lines to the fuel rail assembly and connect the hoses to the fuel pressure regulator. Connect the electrical connector for the fuel injectors and install the collector for the intake manifold with a socket wrench. Connect the cable to the negative battery terminal. Start the engine and check for fuel leaks.

ReadMore

Wednesday, February 26, 2014

Auto Clear Coat Urethane Safety

Auto Clear Coat Urethane Safety

Urethane clear coats are applied to create a lasting shine and to provide protection for the base colors that lay underneath them. As with any solvent-based materials, safety guidelines always should be followed when urethane products are used.

Inhalation

    Urethane clear coats contain harmful vapors. The product always should be used in a well-ventilated area or in closed conditions where extraction is available. Users should wear suitable air-fed respiratory equipment at all times.

Skin and Eyes

    Contact with skin and eyes should be avoided at all times. Protective clothing, eye-wear and gloves always should be worn during handling. In the event of accidental spillage, urethane clear coats should be washed off with copious amounts of water and medical advice should be considered.

Consumption

    Urethane clear coats should never be consumed internally. If accidental swallowing occurs, do not induce vomiting and seek medical advice immediately.

Usage

    Always use urethane clear coats in accordance with manufacturer instructions and never use non-compliant solvents to help harden or thin the material. Users with respiratory problems should avoid contact with all urethane-based products.

ReadMore

How to Replace the Head Gasket on a 1999 Mazda 626

Manufactured for the export market, the Mazda 626 first appeared in the U.S. in 1979. The 1999 version of the 626 is a four-door family sedan that was powered by a 2.0-liter, inline four-cylinder engine that produced 125 horsepower and 127 foot-pounds of torque. A leaking gasket that caused poor engine performance was one of the engines issues.

Instructions

    1

    Disconnect the negative (ground) battery cable. Remove the timing belt. Remove the front exhaust pipe. Remove the air cleaner. Remove the accelerator cable. Disconnect the fuel hose. Remove the ignition coil.

    2

    Drain the engine coolant. Verify the engine oil level. Inspect for engine oil, engine coolant and fuel leakage. Inspect the pulleys and the drive belt for runout and contact.

    3

    Hold the camshaft by using a wrench on the cast hexagon, and loosen the camshaft pulley lock bolt. Loosen the camshaft cap bolts in two or three steps. Arrange the removed camshaft caps to ensure correct placement during installation. Temporarily install the number three engine mount rubber to support the engine. Loosen the cylinder head bolts in two or three steps. Remove the cylinder head. Remove the old head gasket. Clean the surface of the block from any dirt and debris with a degreaser. Place the new head gasket on the block.

    4

    Measure the length of each bolt used to tighten the cylinder head. Replace any that exceed the maximum length. Standard length is 4.103 to 4.125 inches. Maximum length would be 4.154 inches. Tighten the cylinder head bolts in two or three steps. Tightening torque shouldnt exceed 16.2 foot-pounds for each step. To install everything back, just follow the removal sequence in reverse. Remember to connect the negative battery cable back to the battery.

ReadMore

Tuesday, February 25, 2014

What to Expect When Having a Transmission Rebuilt

What to Expect When Having a Transmission Rebuilt

Transmissions allow you to easily shift a vehicle into drive, park or reverse when it is working properly. Low fluid levels or even a bad solenoid cause problems that can be handled without the need to tear down the entire transmission. However, internal problems more serious than these can also occur, bringing about the need to have the transmission rebuilt.

Search

    Many transmission shops use to do transmission rebuilding jobs. By replacing transmissions instead of rebuilding them, shops can earn more profits for themselves. Because of this, you may need to do a thorough search before you can find a shop willing to rebuild your transmission.

Cost

    A good way to estimate what it will cost you to have your transmission rebuilt is by taking the cost of what the transmission would cost new and splitting that in half. For example, if your transmission cost $2,000 new, you can expect to pay about $1,000 to have it rebuilt.

Labor

    The labor performed with rebuilding a transmission starts with a total disassembling of the transmission. Each part is then caully inspected to see whether cleaning is needed or total replacement of the part. Some parts are often replaced regardless of their condition, such as the torque converter.

ReadMore