Pages

Tuesday, February 4, 2014

The Average Cost to Replace an Automatic Transmission

The Average Cost to Replace an Automatic Transmission

Without a working transmission, your vehicle is virtually unusable. Having the right information on the costs and facts of automatic transmission replacement will put you in a better position to get your automobile back on the road.

Labor

    Labor cost is higher for an automatic transmission because more work is needed than would be for a manual. Besides the transmission, the torque converter will have to be changed out as well. The flushing of cooling lines is also a necessary part of transmission replacement.

Cost

    Automatic transmission replacement can vary from place to place. You may be able to locate a shop that will do the job for under $2,000. However, depending on your vehicle type, your bill may end up being well over $3,000.

Considerations

    Because of the prices of transmission replacement, you may want to consider having it rebuilt instead. You will first need to find out the seriousness of your transmission problem. If it is only minor, rebuilding the transmission could be a better route.

ReadMore

Monday, February 3, 2014

How to Replace the Taillight Bulb on a 1997 Chevy Silverado

Replacing the taillight bulbs in the taillight assemblies of your Chevy Silverado pickup will only take a few minutes and requires only simple hand tools to complete the job. The bulbs are housed within a plastic taillight assembly and the assembly requires removal from the truck to access the bulb. The 3057 bulbs used in the taillights of the Silverado are readily available from any parts store or most major department stores.

Instructions

    1

    Open the tailgate of your Silverado and locate the two taillight retaining screws on the inside edge of each taillight assembly. These are Phillips-head screws on the inner edge of the end of the cargo-bed wall, where the tailgate rests when closed.

    2

    Remove the two retaining screws with a Phillips screwdriver, setting the screws aside for reuse later. Grasp the taillight assembly and pull it straight out of the body until you can access the wiring harness connection on the back of the assembly.

    3

    Depress the locking tab on the connector and pull it off the taillight assembly. Grasp the socket on the back of the taillight, turn it counterclockwise -turn, and remove it from the assembly. Pull the failed bulb out of the socket and discard it.

    4

    Push a new bulb into the socket. Insert the bulb and socket into the rear of the taillight assembly and turn the assembly clockwise to lock it in place. Connect the wiring harness connector to the taillight assembly, pushing it in until it snaps in place.

    5

    Position the taillight assembly on the rear of the Silverado, making sure it seats completely; then install the two retaining screws. Tighten the screws with a Phillips screwdriver and close the tailgate.

ReadMore

How to Reset the Service Engine Light on a 2002 Mitsubitshi Eclipse

The 2002 Mitsubishi Eclipse has an On-Board Diagnostics system that monitors the vehicles emissions components and many of the vehicles mechanical aspects. When the "Service Engine" light illuminates on the instrument panel, you need to take your vehicle to a qualified mechanic for service before resetting the light. Otherwise, the computer wont be able to determine the next service date. Also, you will be erasing the trouble codes your mechanic needs to diagnose the problem.

Instructions

    1

    Find the diagnostic port on the Eclipse on the underside of the dashboard, near the drivers side. Plug the OBD code scanner into the port.

    2

    Put the key in the ignition and turn the engine to the "On" position. Make sure you dont start the engine. This will power on the code scanner automatically.

    3

    Wait for the OBD code scanner to run through its test. When it displays the trouble codes, write them on a piece of paper. Take the codes to your mechanic or look them up yourself in a repair manual. Unplug the code scanner and have the vehicle serviced.

    4

    Repeat Steps 1 and 2. Wait for the trouble codes to appear. Press "Delete" or another similar button on your scanner. This will erase the codes and reset the light. Unplug the scanner from the port and turn off the vehicle.

    5

    Turn on the engine and verify that the service engine light has turned off.

ReadMore

Sunday, February 2, 2014

Tutorial on Replacing the Thermostat of a Toyota Tacoma

Tutorial on Replacing the Thermostat of a Toyota Tacoma

The thermostat in your Toyota Tacoma is an essential part of the trucks engine cooling system. The thermostat expands when the coolant in your engine becomes too hot, opening a valve that allows much more coolant to circulate through the system. The increase in coolant flowing through the radiator brings down the overall fluid temperature, and as a result, your trucks engine continues to operate within the optimal engine temperature. When the thermostat is no longer working properly, the engine overheats and the thermostat needs to be replaced.

Instructions

    1

    Remove the lower radiator hose by unscrewing the clamps and pulling off the hose.

    2

    Unscrew the two bolts on top of the thermostat.

    3

    Remove the thermostat and the gasket from the water pump.

    4

    Clean the thermostat housing, removing any dirt and leftover gasket pieces.

    5

    Line up the valve on the new thermostat with the point on the inlet, and place the new thermostat and gasket into the thermostat housing.

    6

    Screw the two bolts you removed earlier back into place.

    7

    Reattach the lower radiator hose and clamp it into place.

    8

    Top off the radiator with fresh coolant.

ReadMore

Buick Car Recalls

Buick Car Recalls

To protect their consumers, vehicle manufacturers will recall any vehicle model that puts a consumers safety at risk. Due to safety belt buckle problems, steering knuckle problems and possible electrical shorts, Buick has recalled several vehicles to correct problems in their late-model cars. Under recall, needed repairs are completed free of charge.

2009 Buick Lucerne

    On June 4, 2010, General Motors Corporation started a recall to correct an electrical system malfunction in 1,365,070 2009 Buick Lucernes. Under the recall, a fuse is added to the cars control circuit harness to reduce the risk of a electrical short on the printed circuit board.

    Because additional problems concerning the heated washer fluid modules (HWFS) were reported after the electrical problems were corrected, dealers are also permanently disabling and removing the HWFS. The degree of damage around the modules varied from vehicle to vehicle. Some modules experienced slight melting while others had extensive melting of the plastic around the HWFS fluid chamber. An insert is being will be attached to the owners manual to indicate that the feature has been disabled and removed from the vehicle.

    Buick

    866-608-8080

    Recall ID 10V240000 - electrical system

2007 Buick Lacrosse

    Dorman Products Inc. is recalling 979 steering knuckles used in certain 2007 Buick Lacrosse cars. The steering knuckle parts being recalled are Dorman part P/NOS. 697-902 and 697-903. Both parts were sold under Dormans "OE Solutions" brand name. Due to a design defect, the steering knuckle in the HUB area could break and result in a loss of steering control. Dorman will replace the defective parts free of charge and reimburse for all labor charges. The recall began on February 23, 2009. Dorman can be contacted directly.

    Dorman

    800-523-2492

    Recall ID 09E005000 -Steering

2009 Buick Enclave

    General Motors is recalling 207,210 Buick Enclaves due to possible safely belt buckle restrictions. When the second row seat is returned to an upright position, the side trim may block the safely belt buckle from completely springing upwards. Applying force to return the second row seat to an upward position may result in the red release button being partially pressed. When pressed, the seat occupants will not be properly restrained. Under the recall, dealers are adjusting the second row side trim shields. Any damaged safety belt buckles will be replaced free of charge. The safety recall began on August 18, 2010. Buick may be called directly for information.

    Buick

    866-608-8080

    Recall ID 10V3750000 - Seat Belt

ReadMore

Saturday, February 1, 2014

How to Hook Up a Tow Dolly Lights to a Car

How to Hook Up a Tow Dolly & Lights to a Car

Whether you need to tow your car to the local car repair shop or behind your RV while driving across the county, you will need to buy or rent a tow dolly. A tow dolly is the safe and legal way to tow your car. It has a single axle with a tongue, similar to the letter T. The tongue will hook to the towing package on the back of the vehicle which will tow the car. The towing package consists of a hitch and wiring harness installed on the back of your vehicle, and the wiring to control the lights on the tow dolly hooks into the wiring harness of the vehicle itself.

Instructions

    1

    Loosen the coupler latch on the tongue of the tow dolly and place the coupler over the 2-inch ball of the hitch on the vehicle which will be towing the dolly. Push the towing dolly back and forth a bit to ensure the coupler is seated properly on the 2-inch ball.

    2

    Push down on the latch to close the coupler latch over the 2-inch ball and place the pin through the latch to securely lock the tow dolly onto the hitch. Pull up on the towing dolly to test if it is secured. If the coupler seems loose on the ball, adjust the coupler, using a wrench.

    3

    Connect the wiring plug of the tow dolly to the plug beside the hitch. If the wires do not have a plug, then connect the color coded wires of the dolly to the corresponding wires of the towing package. The yellow wire controls the left blinker, the green wire controls the right blinker, the brown wire controls the tail lights, the white wire is the ground and the red wire is for optional brakes on the dolly.

    4

    Attach the safety chains to hitch. Crisscross the chains, allowing slack in the chains for moving around corners.

ReadMore

Maryland Attorneys the Lemon Law

Maryland Attorneys & the Lemon Law

A "lemon" ers to a defective car, which spends more time in the shop than it does on the road. As a result, Maryland adopted a "lemon law" to help outline how car owners can deal with their lemons.

Identification

    The Maryland Lemon Law categorizes a lemon as a vehicle that was purchased or leased within two years with less than 18,000 miles. The vehicle either has had problems to the point of being out of commission for at least 30 days or has significant problems with the steering or braking systems.

Action

    If you think you have a lemon, first write to the manufacturer and give them the chance to fix the defect. If they cannot fix it, they must buy back the car, replace it or seek arbitration. If you and the manufacturer cannot come to an agreement, the last resort option is to bring in a Maryland attorney and file a lawsuit.

Attorneys

    Maryland lemon law attorneys, such as Kimmel & Silverman, have experience with lemon law cases and are familiar with the process. You can also find a lemon law attorney through the Maryland Bar Association.

ReadMore