Friday, February 14, 2014
How to Check an Electric Brake Magnet
A faulty brake magnet can severely impact the stopping power of a trailer. While some magnet problems will be apparent upon visual inspection, there may also be electrical problems that can impact performance. A compromised brake magnet can lead to weak or surging brakes, or cause the brakes to pull to one side. It is important to inspect and test the magnets each time the brakes are worked on to ensure maximum effectiveness.
Instructions
- 1
Jack the trailer up high enough that each wheel turns freely. Secure the trailer with blocks under the frame at each end and on both sides to reduce the danger of the trailer falling on you should the jacks fail.
2Remove the lug nuts and pull the tires and rims off of each axle.
3Take off the grease cap and remove the cotter pin and castle nut. If there is a spindle washer, remove this too. Gently remove the outer bearing, drum, seal and inner bearing.
4Locate the brake magnet. Take a straight edge tool and lay it across the top of the magnet. The edge of the magnet should be parallel to the straight edge all the way across. Any pitting or changes in the magnets surface indicate abnormal wear and the magnet should be replaced.
5Check the center of the magnet for copper coil. If any coil can be seen, the magnet is worn out and should be replaced.
6Visually inspect the magnet for grease or oil residue. If any is found, replace the magnet.
7Check the magnet for short circuits. Disconnect the leads and the strain relief so that you can pull the leads through the backing plate. Unclip the leads from the lever arm and disconnect the magnet. Connect the positive battery terminal to one end of the ammeter lead and the other end to one of the magnet wires. Use a piece of 16-gauge wire and connect the magnet housing to the negative battery terminal. The ammeter should not show a current reading. If it does, a short exists and the magnet should be replaced.
8Keeping the magnet wire connected to the ammeter lead, take the other magnet wire and attach it to the negative battery terminal. Take the other ammeter lead and attach it to the positive terminal. An amp reading of 3.2 or more at 12 volts means there is a short circuit in the coil and the magnet should be replaced.
9Check the brake lining, shoes and repack the bearings if needed while the wheel assembly is apart. Put the parts back on the axle in the opposite order of how you removed them.
How to Program the Keyless Entry Remote on a Saab 900
Most Saab 900s produced since 1996 come standard with a key-less entry system that allows you to lock and unlock the car with a key fob. If you replace the battery in the key fob or need to replace a lost key fob, you will need to reprogram the device. Reprogramming, after replacing the battery, takes just a few seconds and can be done yourself while programming a new key fob will take 30 to 60 minutes at a dealership or repair center.
Instructions
Programming After Battery Replacement
- 1
Stand near the car and press the "Unlock" button five times in quick succession.
2Listen for a beep or chirp from the car to signal that you have successfully reprogrammed the fob.
3Remove the battery and reinsert it into the fob if the programming wasnt successful. Move closer to the car. Press the "Unlock" button five times again quickly.
Programming a New Fob
- 4
Verify that you have one working key fob. Without at least one working fob, you will not be able to program additional fobs without replacing the Column Integrated Module (CIM).
5Visit a repair shop or dealer with a GM Tech II scan tool. Only someone with this device can program a new key fob.
6Bring all working keys and fobs when you get the new fob programmed. Any old fobs will be removed from the system at this time and will no longer work. You can have up to four fobs per car.
Thursday, February 13, 2014
How to Replace Lettering on a Range Rover
Replacing the vinyl lettering on a Range Rover can be done without too many headaches with a few common household materials and a little skill. Removing the vinyl lettering will allow you to easily replace the original Range Rover lettering with whatever you may want to put on the vehicle.
Instructions
- 1
Saturate a cotton ball with rubbing alcohol.
2Rub the alcohol saturated cotton ball over each vinyl letter you want to remove from the Range Rover. Make sure that as you do this you thoroughly coat each vinyl letter with alcohol. The alcohol will either eat away at the vinyl or the glue underneath, allowing you to remove the lettering.
3Scrape each letter off using the scraping knife caully so that you do not damage the paint on the vehicle. It will help to have an alcohol saturated cotton ball with you as you do this because it may be necessary to re-saturate each letter with alcohol as you are scraping it off.
4Rub an alcohol-saturated cotton ball over the area where all of the lettering was, cleaning up any glue residue that may remain. This will prepare the area for placing new graphics or lettering on the vehicle.
5Measure the area that you wish to place the new vinyl letters or graphics.
6Measure the vinyl graphics or lettering and make sure that they will fit in the area that you wish to place them.
7Tape with masking tape the top of the graphics or lettering to the top of the area on the vehicle you want to place the new graphics or lettering.
8Peel off the backing on the vinyl letters or graphics that you wish to place on the vehicle.
9Rub the letters or graphics into place with the squeegee. The glue on the letters or graphics will attach them to the vehicle.
10Rub alcohol caully with a cotton swab over any excess glue leaking out under the edges of the letters or graphics.
How to Replace a Head Gasket on a GL 1100 Gold Wing
The GL1100 Gold Wing was introduced in 1980 and was based off the GL1000. The GL1100 was equipped with an 1,085-cc displacement, liquid-cooled opposed, four-cylinder engine. High performance valve timing and 30-mm bore carburetors contributed to its well deserved reputation of power and reliability. Performing engine repairs, such as general maintenance and routine adjustments, are in general not difficult on this motorcycle. However, replacing the head gasket is a challenging repair job. This repair job can be done without removing the engine from the motorcycle.
Instructions
- 1
Lift the motorcycle onto its center stand. Drain the coolant from the petcock at the bottom of the radiator into a drain pan. Dispose of the used antifreeze in accordance with local disposal laws. Remove the black bolts at the bottom of the radiator and slide the radiator forward. Remove spark plug wires from the spark plugs and set them aside.
2Remove the eight bolts holding the plastic camshaft belt covers. Remove the camshaft belt covers and set them aside. Mark the position of the cam sprockets with a tic-mark on the cylinder block and a matching mark on the camshaft sprocket. Loosen the timing belt tensioners and remove the timing belt.
3Remove the fuel pump if working on the right side of the engine. Remove the electronic ignition reluctor and cover if working on the left side of the engine. Remove the four bolts holding the valve covers and set the covers aside. Remove the four bolts holding down the intake manifolds.
4Remove the six bolts holding the rocker shaft covers and remove rocker shafts. Remove the two bolts holding the camshaft pulley back plate. Tap the rocker shaft with a rubber mallet if necessary to assist in removal.
5Remove the exhaust manifold bolts. Remove the six 10-mm cylinder head bolts and the the one small 6-mm bolt at bottom of head. Tap the head off using a rubber mallet. Bump the engine with the starter if the head is difficult to remove. This method uses the natural compression of the engine to pop the head loose.
6Remove the oil restrictor orifice from crankcase. Remove all traces of old head gasket with a gasket scraper and rag. Ensure the block and head mating surfaces are clean, shiny and all traces of the old head gasket are removed. Clean the oil restrictor and ensure no sludge or other dirt is in the orifice passage in the block. Clean all carbon from the head using a wire brush and scraper. Check the head check for cracks or other damage. Repair any problems with the head as required.
7Install the clean oil orifice using two new O rings. Replace O rings on the head water pipe with new ones and lubricate them with motor oil. Install the head onto the block finger tight using a new head gasket. Do not use any kind of sealer on the gasket, it must be installed dry.
8Tighten the six 10-mm head bolts to 40 ft-lb with a torque wrench in a crisscross pattern. Install the 6-mm bolt at bottom of the head and torque to 10 ft-lb. Install the intake manifolds with the correct bolts. Ensure the manifold O rings are in good condition or replace as required.
9Install the camshaft in the head and tighten the six camshaft bolts to 21 ft-lb. Install the camshaft pulley back plate using a new gasket and tighten the bolts to 9 ft-lb. Install the new timing belts using the alignment marks from Step 2 as erence. Tighten down the timing belt adjusters when everything is lined up. Ensure everything is correct before proceeding to the next steps.
10Install the electronic ignition reluctor and cover plate or fuel pump as required. Replace the exhaust manifold bolts. Replace the valve cover and radiator bolts. Fill the radiator up to the recommended level with new antifreeze. Replace the spark plug wires onto the spark plugs.
11Start the engine and check for leaks in the cooling system. Add coolant as necessary when the engine warms up to normal operating temperature.
Wednesday, February 12, 2014
Rotation Direction for a Pontiac 350 Engine
Pontiac has always been GMs excitement division, and its V-8 production strategy was one reason its stayed that way for so long. Unlike many other divisions that had large- and small-block engine families, Pontiac had only one engine that spanned from 265 all the way up to 455 cubic inches. Smaller-displacement engines like the 350 were oft-overlooked cult classics, mostly because of serious junkyard upgrades in the form of higher flowing heads, intakes and cam packages for the 428 and 455.
Rotation Direction
Most V-8 and V-6 engines use common-journal crankshafts, meaning that the connecting rods from two opposing cylinders ride on one arm of the crankshaft. Such is the case here: Pistons 1 and 2 share a crankshaft arm, as do 3 and 4, 5 and 6, and 7 and 8. Knowing this, and the fact that the even numbers are on the passenger side of the block, you can figure out the direction of rotation from the engines firing order.
The Pontiacs firing order is 2-1-8-4-3-6-5-7. Notice that in this order, you have a couple of pairs: 2-1 and 6-5. Since you know that those cylinders share a common arm, you can deduce that the crankshaft hits the passenger side first, and then the driver side. Theore, the crankshaft rotation is clockwise when looking at the engine from the front, counterclockwise when looking at it from the rear. Inside the distributor, the rotor spins counterclockwise.
How to Disconnect a BMW X5 2002 Battery
The 2002 BMW X5 battery is located in the trunk, beneath the spare tire. When you need to replace the battery in your X5, you need to remove the spare tire from the trunk to access it. Buy a replacement battery from an auto parts retailer or BMW dealer. Change the battery yourself at home for a fraction of what it would cost to have a mechanic do the job.
Instructions
- 1
Remove the key from the ignition. Open the trunk of the X5.
2Lift up the carpet lining above the spare tire. Remove the four retaining nuts around the center of the spare tire with a 10-mm socket attached to a ratchet.
3Lift the spare tire out of the trunk. Remove the bolts on each end of the crossbar over the battery with a 13-mm socket and ratchet. Lift the crossbar out of the trunk. Loosen the negative battery cable with a 10-mm socket and ratchet. Remove the cable from the battery. Repeat the process on the positive cable.
4Lift the battery out of the trunk. Insert the new battery in the same alignment as the old one. Attach the positive battery cable and tighten it with the 10-mm socket and ratchet. Repeat the process with the negative cable. Replace the crossbar and secure the bolts with a 13-mm socket and ratchet.
5Replace the spare tire. Secure the retaining nuts with a 10-mm socket and ratchet set. Replace the carpet over the spare tire area and close the trunk.
Tuesday, February 11, 2014
How to Install an Electrical Oil Pressure Gauge
Electric oil pressure gauges are easy for a DIY-mechanic to install, whether replacing a faulty oil pressure gauge, or a custom, after-market look is desired. Oil pressure gauges are designed to inform the driver when the oil falls below a safe operating level, or when the oil pressure is too high. Driving a vehicle without an oil pressure gauge can lead to catastrophic engine failure. Most oil pressure gauges come with mounting panels and the necessary installation hardware. The necessary hardware can be purchased from an auto parts dealer, if not included with the oil pressure gauge.
Instructions
- 1
Choose a suitable location to mount the oil pressure gauge; mount the gauge so it is easily viewed while driving. Common mounting locations for aftermarket oil pressure gauges include under the dash, on top of the dash, or set into the dashboard.
2Mount the gauge panel to the dash with a screwdriver and screws provided in the kit; set the gauge aside. This makes it easier to connect the wires. If mounting the gauge in the dash, drill a hole in the dash 1/8-inch larger in diameter than the size of the gauge.
3Remove the oil drain plug from the oil pan with a wrench and drain the old oil into a oil catch pan. This is an opportune time to change the oil filter as well.
4Remove the old oil pressure sending unit with a ratchet and socket; the oil pressure sending unit is shaped like a cylinder and is usually located near the oil filter. Refer to the new oil pressure sending unit in the oil pressure gauge kit to help you identify the part.
5Connect the signal wire to the sending unit and run it through a grommet in the firewall in close proximity to the gauge. Run the wire through the gauge panel hole, or the pre-drilled hole in the dashboard, allowing extra wire for easy connecting.
6Connect the signal wire to the post on the back of the gauge. The gauge posts are marked for correct wire installation.
7Run a power supply wire from a switched 12-volt power supply, such as the cigarette lighter, dome light, radio, or fuel pump, to the power post on the gauge. The power supply must be switched to operate on and off with the ignition.
8Run a ground wire from the vehicle chassis to the ground post on the gauge; a poor ground can result in an inoperable gauge or false reading. Use an existing grommet in the firewall, or drill a hole in the body of the vehicle, and route the wire to the chassis or frame.
9Mount the gauge into the gauge panel, or the hole in the dash, with the supplied mounting hardware in the kit.
10Install the oil pan drain plug and fill the engine with oil.
11Start the engine to check the operation of the gauge.