Friday, January 10, 2014
T18 Transmission Specs
The Ford T18 transmission was produced by Borg-Warner between 1965 to 1991. The Borg-Warner T18 transmission replaced the earlier T98 transmission model in both Ford, Jeep and IH 1/2-ton, 3/4-ton and 1-ton heavy-duty trucks. There were two variants of the T18 transmission produced by Borg-Warner. It is advised to inspect the model number located beneath the top shaft cover before attempting to install a Jeep T18 transmission in a Ford vehicle.
Borg-Warner Specifications
The standard Borg-Warner T18 transmission has a length of 11.87 inches, a total height of 17.5 inches, and a total weight of 145 lbs. The T18 is cased in cast-iron. The top cover is also cast-iron. The PTO port is located on the passenger side of the vehicle. The T18 has gearing ratios of 6.32, 3.09, 1.69, 1.0 and R7.44. There are slight variations in the length of Ford T18 and Jeep T18 transmissions.
Ford T18 Specifications
The Ford T18 model transmission has a 1 and 1/16 inch diameter. The Ford T18 has a ten-spline shaft extending 6 and 1/2 inches from the front face of the transmission.The Ford T18 pilot tip is 18 mm. The front-bearing retainer flange is 4.85 inches. The diameter of the retainer tube is 1.43 inches in diameter. The front bolt of the T18 is patterned in a typical Ford symmetrical butterfly pattern, 6 and 5/16 inches in length by 8 and 1/2 inches in width.
Jeep T18 Specifications
There were roughly twelve variations of the Jeep T18 transmission released from 1966 to 1984. There are subtle variations present in each of the editions, but the key differences are present in the gear ratios and shaft length. Between 1972 to 1975 the standard gear ratio of the Jeep T18 was 4.02:1. Between 1977 to 1979 the gear ratio of the Jeep T18 was adapted to 6.32:1. The PTO port of Jeep T18 transmissions is located on the drivers side of the vehicle.
The Jeep T18 transmission was originally released with a length of 11.87 inches, a total height of 17.1 inches, and a weight of 145 lbs. Both the shaft and the top cover of the transmission are encased in cast-iron. Variations of the Jeep T18 transmission feature gear ratios of either 6.32, 3.09, 1.69, 1.0,and R7.44, or 4.02, 2.41, 1.41 and 1.0 in the earlier release.
Friday, December 27, 2013
How to Identify Chevy 350 Engines
If you have a Chevrolet car or truck made between 1967 and 1997, theres a good chance it has a 350-cubic-inch engine. The Chevrolet 350 small-block engine was offered in many Chevrolet cars and trucks and in other General Motors vehicles as well. The 350 became Chevrolets primary work-horse small-block engine after the demise of the 327 and 283 engines. The 350 is identified using both visual clues and casting numbers.
Instructions
- 1
Count the number of spark plugs. The 350 is an eight-cylinder engine
2Inspect the engine compartment to locate identification tags. GM usually places various tags, decals and other identification devices throughout the engine compartment. These usually provide any necessary information if it is not worn off.
3Locate the casting identification number on the engine block. This number is stamped on a pad just forward of the right-side (passengers side) cylinder head and may be hidden by the alternator. Remove the alternator if necessary. The ID number usually consists of eight digits in a combination of numbers and letters.
4Decode the ID number according to Chevrolets code system. For example, the number V0908CNJ breaks down as follows: V is the engine plant, followed by the month and day of manufacture and the engine suffix code. ID number V0908CNJ was manufactured at the Flint engine plant on October 8 and was originally installed in a 1970 Caprice with 250 horsepower. To decode the engine suffix, cross-referencing is necessary.
Thursday, December 26, 2013
Headlight Installation Problems
Installation problems with headlights can be a major safety issue because nighttime driving is nearly impossible when headlights are not working properly. Although some headlights can function after well over 1,500 hours of use, even a few minutes of driving without them can be a dangerous venture.
Installation Problems
When installing new headlights, sometimes one or more bulbs will fail to light up. A corroded socket is sometimes to blame for this kind of issue. By applying a cleaner made specifically for electronics, the connection can sometimes be revived. If not, you will likely need a new socket altogether.
Fuse Problems
Voltage issues will also prevent headlights from coming on. Fuses should be checked, and any blown fuse should be replaced. If the new fuse blows as well after replacement, the problem is likely due to a short somewhere in the wiring of the headlights circuit.
Charging Problems
If your headlights lose brightness each time you rev your motor, a problem is likely present somewhere within your vehicles charging system. A faulty alternator is an example of this. Checking your car batterys voltage can help as any voltage reading under 13 volts suggests that the charging system is indeed the problem.
Wednesday, December 25, 2013
How to Change Fuses on a 2001 Malibu
Your 2001 Chevrolet Malibu contains three fuse boxes that, like the fuses in your home, protect your cars wiring system. If an electrical device in your car, such as the radio or the interior lights, has a problem and draws too much power, the fuse controlling it will blow, stopping electricity from flowing and protecting the wiring inside your car. If that happens, you will need to replace the blown fuse to restore power to the device.
Instructions
- 1
Turn off your cars engine.
2Use your owners manual to identify where the affected fuse is. Open the fuse panel by grasping the handle and pulling out.
3Identify the blown fuse. To remove a fuse, grasp it between your fingers and give it a firm pull. If you need to remove a fuse from the engine compartment, there is a special tool in that fuse box. The element of the damaged fuse will look burned or separated.
4Replace the damaged fuse with a new one.
5Replace the door of the fuse compartment. Do this by inserting the doors hooks into the slots and then pushing the rest of the door into place.
Tuesday, December 24, 2013
High Impact Air Gun Tools
Pneumatic tools offer reliability and strength. An air gun uses very few moving parts. Air pressure moves pistons that generate the power. The only maintenance needed on an air gun, or pneumatic tool, is daily oiling if the tool is not self-oiling. The main goal of an air gun is to deliver a powerful tool capable of intense amounts of torque or pressure. The most common high-impact air tools are air hammers, air drills and impact wrenches.
Air Hammers
An air hammer is not an elegant tool. It is used to repeatedly deliver blows to an object. The hammer comes with a variety of tips to shape or smooth metals. An internal piston is actuated by the air pressure from an air compressor. The piston repeatedly shoots forward and back. The different tips determine what the movement accomplishes. A flat-head hammer tip allows a worker to create a curve in a piece of sheet metal. The flat-head condenses and spreads out the metal as the piston hammers the ball into the surface of the metal. Chisel tips can be used to chip away at brick or stone, or to gouge metal.
Air Drills
Air drills use air pressure to generate high levels of rotation comparable to battery-operated drills. The tool is weaker than the electrical variation but is less likely to break down due to the limited number of moving parts. The tool delivers steady rotation regardless of the material. Electric drill motors can snag up in tough materials. Air drills are available in a standard gun style, similar to electric, and hand-held variations similar to electric screwdrivers. The tool has a quick-release connection on some models, or the standard chuck-key connection that requires a specific tool to unlock the bit.
Impact Wrenches
Impact wrenches are the most common type of high-impact air guns. An impact wrench combines the elements of an air hammer with an air drill. Rather than just spinning a gear, the tool delivers air pressure to an internal hammer that builds up briefly before spinning the gear. The rapid discharge of stored pressure or energy translates to high-torque rotation. Impact wrenches work best on stubborn or damaged bolts. The manual equivalent to this tool would be to place a wrench on a bolt and hammer at it with a sledge hammer. The tool, like all air guns, is reliable with minimal moving parts. The only maintenance necessary is to oil the tool daily. The oil prevents the internal pistons and gears from becoming sticky or dry.
Monday, December 23, 2013
1998 Chevrolet Silverado Brake Box Installation
The Chevrolet C/K series is a family of full-size pickup trucks that General Motors has manufactured since 1960. The Silverado was the top trim level for the 1998 C/K trucks, and General Motors upgraded it to a separate model beginning with the 1999 model-year. The 1998 Silverado comes standard with an anti-lock braking system (ABS), which allows the vehicle to stop more effectively under emergency conditions. The Electro-Hydraulic Control Unit (EHCU) controls the amount of braking force to apply to each wheel.
Instructions
- 1
Locate the EHCU in the engine compartment on the left side of the engine. It is the black box with four brake lines running to it.
2Detach the connectors for the electrical wiring from the EHCU. Disconnect the fittings for the brake lines with a socket wrench and detach the brake lines from the EHCU.
3Disconnect the mounting bolts for the EHCU bracket with a socket wrench and remove the bracket from the vehicle. Remove the mounting bolts from the EHCU and detach the EHCU from its bracket.
4Install the new EHCU onto its bracket and tighten the mounting bolts to 5 foot-pounds with a torque wrench. Connect the EHCU bracket to the vehicle and tighten the mounting bolts for the bracket to 33 foot-pounds.
5Connect the brake lines to their original positions on the EHCU and tighten the fittings to 16 foot-pounds with a torque wrench. Attach the electrical connectors for the EHCU, ensuring the connections are secure.
6Connect a TECH-1 scanning tool to the vehicles data link connector. Bleed the EHCU valve with three J-39177 tools and correct any ABS errors reported by the scanning tool. A professional mechanic would normally perform this step.
Sunday, December 22, 2013
289 Intake Torque Specs
Correct torque value for the bolts on a vehicle is important for auto safety. A torque value that should be paid particular attention to is that of the intake manifold bolts. The intake manifold bolts must have the correct torque value, as well as be torqued in the proper sequence.
Reasoning
The intake manifold is of manufactured of cast iron, and it is bolted to a cast iron block, so proper torque ensures the casting is not damaged. The proper torque also ensures the intake manifold gasket properly seals, preventing debris from entering the combustion chamber. It also prevents vacuum leaks from forming and causing running issues.
How
Proper torque is achieved with a torque wrench. A torque wrench is very similar to a basic ratchet, but it is able to be set to a certain torque value. When the set torque value is achieved, it emits an audible signal, typically a clicking sound, to alert the user.
Amount
Torque is measured in a value known as foot-pounds, sometimes abbreviated "ft-lb." All 12 of the bolts on the intake manifold of a 289 engine require a final torque value of 25 ft-lb.
Process
You cannot simply tighten the bolts in straight sequence, as the last bolts tightened do not seal as well as the first. There is an alternating pattern to assure the best seal. Starting with the front passengers side bolt and moving clockwise, the torque sequence goes 9-5-1-3-7-11-12-8-4-2-6-10 (see reference for image). The sequence must be performed three times to ensure accuracy.