Pages

Tuesday, February 18, 2014

How to Balance Semi Tires

How to Balance Semi Tires

You see them every day as you drive down the highway, giant vehicles that are used to distribute our goods and food. As drivers on the road we are extra caul not to get in the way of these trucks. As it is, we see so many accidents involving semi trucks because they are big and bulky. It is important that the driver is in-tune with his truck because even the smallest issue can cause a giant problem. This is why it is so important that the tires on these semi trucks are balanced correctly. This job requires the use of specialized truck tire tools. It should take you about an hour to balance your semi truck tires.

Instructions

    1

    Park your semi truck on level ground and set the brakes.

    2

    Block the front and back side of one of the tires you are not working on yet by setting one of the 4x4 blocks in front of a tire and one behind the same tire.

    3

    Jack up one of the wheels by positioning the big rig jack under the axle and jacking it up. Slide the jack stand under the axle for extra security.

    4

    Remove the lug nuts with the lug nut wrench by placing the end over the nut and turning the nut counterclockwise.

    5

    Inspect the operation of the truck bubble balancer. Notice how it works with the plate on top. You will see that there is a bubble in the middle of the balancer. This bubble area looks very much like a carpenters level. You will also see that the balancer has a control lever on the side. This is used to raise the wheel into the balancing mode.

    6

    Place the semi tire on the balancer plate so that you can see the bubble area through the center of the wheel. Push the lever to raise the tire into the balancing mode.

    7

    Notice the position of the bubble. The idea is to get that bubble into the center. Lay wheel weights on the tire until you get the bubble in the middle.

    8

    Install the wheel weights using the weight hammer at the locations on the wheel that center the bubble.

    9

    Replace the tire on the truck and install the lug nuts with the big rig lug wrench.

    10

    Remove the jack stand and lower the jack. Repeat for the other tires on the truck.

ReadMore

Monday, February 17, 2014

How to Modify a Cars Exhaust System

Car enthusiasts will often modify a cars exhaust system in order to increase the engine performance or get the noise of the engine to achieve a specific pitch. It requires good knowledge of your cars exhaust system, but it can be completed with a minimum of fuss, provided you follow some basic guidelines.

Instructions

    1

    Raise the car up on a jack or a hydraulic lift so that you can comfortably work on the exhaust system.

    2

    Note the part of the exhaust system you wish to modify and the point in the line at which it is found. You may also want to note any part of the system which is fused or rusted, since these will be more difficult to remove.

    3

    Disconnect each part of the exhaust system, one by one, until you reach the part you want to modify. Generally, a welding torch is required, though you may be able to achieve this simply by removing the bolts that connect it. Take care not to damage any surrounding components in the process.

    4

    Disconnect the old exhaust part you wish to modify and replace it with the new exhaust part. Bolt it or hang it in place on the chassis, but do not tighten the bolts yet. Check that all of the components work correctly before finalizing the addition.

    5

    Attach the remainder of the original exhaust system to the new part, working backwards down the line until you reach the end of the exhaust system.

    6

    Check that each connection is in place and there are no leaks or backups.

    7

    Secure each connection by tightening the bolts or welding them back into place on the chassis.

    8

    Start the car engine and check the exhaust system for any leaks or blockage. Make sure exhaust is coming from the end of the tailpipe as it should and that the sound is modified correctly by the muffler, and locate and seal any leaks.

    9

    Adjust the tailpipe to make sure it is flush with the rear bumper and is not too low to the ground.

ReadMore

How to Put a Belt on a Grand Prix Super Charger

How to Put a Belt on a Grand Prix Super Charger

Putting a new belt on a supercharged Pontiac Grand Prix is nearly identical to putting the belt on a standard Grand Prix. The Grand Prix GTP was introduced in 1997, and with it the supercharged 3800 Series II. The Grand Prix GTP with the supercharged 3800 motor was capable of producing between 200 and 240 horsepower, depending on the use of L36 or L67 engine models. The belt routing between the L36 and L67 is an identical procedure. The Grand Prix was replaced by the Pontiac G6 and G8, before Pontiac was removed in 2009 from the General Motors line of vehicles. Pontiac produced cars since 1926.

Instructions

    1

    Open the hood and stand on the passenger side of the car facing the belt side of the engine. Loop the belt underneath the bottom pulley or the crank pulley, in the outer track provided. The supercharger belt on the 3800 SC is the outermost belt, as there are two belts on this engine.

    2

    Hold the belt taught in your right hand so you do not lose your grip on the crank pulley. Run the belts smooth side or back on the front side of the two supercharger idler pulleys. These two idler pulleys are are about three inches in diameter. The lower supercharger idler pulley sits at the two oclock position, just inches above the crank pulley. The upper idler pulley sits on the top front face of the engine.

    3

    Loop the inside of the belt, or the grooved side, up and over the supercharger. Maintain your grip with your right hand on the belt to maintain your positioning of the belt.

    4

    Set your left hand on the top of the supercharger pulley and hold the belt still. Slide your right hand down the belt toward the front of the car until you reach the tension pulley.

    5

    Pull the belt tight again with your right hand, and use a 3/8-inch ratchet and socket with your left hand to push the tension pulley down towards the bottom of the engine. If you feel uncomfortable in this position, set the ratchet down and grab the belt with your left hand. Use your right hand on the tension pulley if this feels more comfortable to you. Slide the belt over the tension pulley, making sure that you keep your hands clear from the point between the belt and pulley.

    6

    Release the tension pulley and let it retract to its upright position, and remove the ratchet and socket from the tension assembly.

    7

    Inspect your work to make sure the belt is centered on each pulley, and sitting in the proper channels provided in the crank pulley. Clockwise from the supercharger, your belt should go to the front side of the tension pulley, down and around the bottom of the crank pulley, up around the front sides of both idler pulleys, and back to the supercharger.

ReadMore

Sunday, February 16, 2014

How to Install a Harley Hypercharger

The Kuryakyn Hypercharger is a high-flow air cleaner designed to look like a velocity stack or a supercharger. Trap doors on the front of the air cleaner open and close as you open and close the throttle. You will have less leg room with the Hypercharger installed on your Harley than with a stock air cleaner. But even detractors agree that the Hypercharger is a beautiful accessory. Kuryakyn claims that the Hypercharger will add seven horsepower to your Harley over a stock air cleaner.

Instructions

    1

    Remove your air cleaner cover with an Allen wrench.

    2

    Remove the air cleaner assembly with Torx sockets or drivers. Remove the breather tubes by hand. Remove the air cleaner backing plate with a socket wrench and hex socket.

    3

    Close the petcock. Start your Harley and run it until the carburetor is out of gas.

    4

    Mark the throttle cables with masking tape and disconnect them from the throttle cam. Disconnect the fuel line where it enters the carburetor. Disconnect the enricher from the left side of the Harley.

    5

    Pull the carburetor from the black rubber exhaust manifold boot by hand.

    6

    Cut a 1-1/2-inch section of vacuum hose from the hose included with your Hypercharger kit. Assemble the vacuum T included with your kit to form a vacuum line assembly, which will replace your original breather tubes.

    7

    Install the vacuum hose assembly on your carburetor as shown in your Hypercharger kit.

    8

    Reinstall the carburetor in the intake manifold boot. Reconnect the throttle cables and the fuel line. Reconnect the enricher to the left side of the motorcycle.

    9

    Attach the chrome carburetor support bracket to the mouth of the carburetor with the hollow bolts and cup washer included in the kit. Sandwich the intake gasket between the carburetor and the support bracket and tighten the bolts.

    10

    Assemble the rubber boot assembly included with your Hypercharger as shown in the kit. Snap the breather boots in the assembly over the cup washers.

    11

    Remove the round trap door in the Hypercharger with a 1/8-inch Allen wrench. Insert three 1/4-inch socket head cap screws through the mounting holes in the Hypercharger from the inside. Remove the adhesive backing from one of the intake gaskets and place it over the three mounting screws.

    12

    Sandwich the intake gasket between the breather manifold and support bracket. Position the Hypercharger over the breather manifold and bolt the Hypercharger securely to the carburetor support bracket/ breather manifold assembly.

    13

    Replace the trap door and gasket.

    14

    Plug the vacuum hose assembly into the vacuum pod air jet on the back of the Hypercharger.

ReadMore

How to Bleed a 1990 Honda Accord Clutch

How to Bleed a 1990 Honda Accord Clutch

The Honda Accord is the mid-level offering in Hondas Civic, Accord and Camry line of cars. In 1990, the Accord was made 5 inches longer. It received a larger 2.2-liter, four-cylinder engine and two new transmissions, a five-speed manual or a four-speed automatic. The five-speed manual transmission features a hydraulically actuated clutch, with a master cylinder mounted on the firewall next to the brake master cylinder and a slave cylinder mounted on the bell housing.

Instructions

    1

    Raise the front of the Accord with a jack and support it with jack stands on each side of the vehicle.

    2

    Locate the clutch master cylinder next to the brake master cylinder. Clean the top of the master cylinder with a shop rag. Fill the cylinder with fresh brake fluid if necessary.

    3

    Put on safety goggles. Loosen the bleeder screw on the clutch slave cylinder with a wrench but do not open it yet. The clutch slave cylinder is located on the drivers side of the car on the bell housing. Fill a plastic bottle about 1/3 full of brake fluid. Attach a 3-foot length of clear plastic tubing to the bleeder screw and insert the other end into the plastic bottle so it is below the level of the fluid.

    4

    Instruct an assistant to depress the clutch pedal three or four times and then hold pressure on the pedal. Open the bleeder screw with a wrench while your assistant maintains pressure on the pedal. Brake fluid and air bubbles will exit the slave cylinder. Close the bleeder screw. Your assistant can now release the pressure on the clutch pedal.

    5

    Check the fluid level in the master cylinder. You must keep checking the fluid level, as you bleed the slave cylinder, because it will go down every time you open the bleeder screw. Repeat the above process until no air exits the slave cylinder.

    6

    Wipe up any spilled brake fluid with a shop rag. Raise the front of the vehicle with the jack and remove the jack stands. Lower the vehicle. Make sure the master cylinder is full.

ReadMore

Saturday, February 15, 2014

How Does a Chevy EGR Valve Work

How Does a Chevy EGR Valve Work?

A Chevy exhaust gas recirculation (EGR) valve is a necessary part of the cars emissions system. It works by rerouting some of the exhaust gases back into the intake manifold rather than into the atmosphere.

Types

    There are several types of EGR valves with the same function but different modes of operation. Older EGR valves are purely mechanical and run on vacuum; on many newer Chevrolet and other GM models, the valve is controlled entirely by computer. This type uses multiple solenoids to open the valve in response to input from the cars computer, opening and closing the valve to allow exhaust gas flow.

Operation

    Whether the EGR valve uses vacuum or electronic control, it opens when exhaust gases reach a certain temperature or level of backpressure. When the EGR valve opens, some of the exhaust is rerouted to the intake manifold. Since it is less combustible than the air-fuel mixture in the manifold, the temperature drops.

Functions

    The main function of an EGR valve is to lower the amount of nitrogen oxide a car releases into the atmosphere. A failed EGR valve prevents a car from passing emissions testing, if required. The valves secondary function is to lower the temperature in the intake manifold.

ReadMore

How to Install a Rocker Shaft on a Ford 390 Motor

The rocker arm in a combustion engine translates the rotation of the camshaft into the linear movement needed to open the intake valve of the cylinder head. The Ford 390 engine appears on various Ford vehicles from 1961 to 1976, such as some 1968 Mustangs. The rocker shafts on this engine are part of the intake manifold assembly, so the rocker shaft installation procedure requires the removal of any components needed to access the intake manifold.

Instructions

    1

    Drain the coolant from the radiator into a container, and store the coolant for later use.

    2

    Detach the radiator hose from the housing of the thermostat, and remove the bypass hose from the intake manifold. Disconnect the air cleaner and ducts from the the intake manifold with a socket wrench. Remove the distributor cap, and detach its electrical wiring from the engine.

    3

    Mark the distributor housing to indicate the rotors position, and detach the electrical primary wire from the ignition coil. Disconnect the hold-down bolt for the distributor, and remove the distributor from the intake manifold.

    4

    Detach the vacuum lines on the intake manifold, and disconnect the electrical wire for the temperature sending unit. Remove the vacuum lines and fuel line from the carburetor. Disconnect the linkages that attach the carburetor to the intake manifold.

    5

    Disconnect the valve covers with a socket wrench. Turn the four mounting bolts for the rocker shaft two turns counterclockwise, proceeding from front to back. Repeat this until you disconnect all of the mounting bolts for the rocker shaft.

    6

    Mount the new rocker shaft and fasten the mounting bolts with a socket wrench. Tighten each bolt two full turns at a time, proceeding from back to front.

    7

    Install the remaining components by performing steps two through four in reverse sequence. Use the mark that you made on the distributor housing in Step 3 to install the distributor in the correct position. Refill the radiator with coolant, and check the vehicle for fluid leaks.

ReadMore