Repair And Fix it

The parking distance control option on BMWs 2011 X5 truck uses ultrasound sensors integrated into the bumpers to aid in maneuvering tight spaces, such as for parking. The PDC sensors detect objects within 7 feet of the X5, and depending on the PDC option, emit an audible proximity warning, as well as visual warning on the control display panel in the middle of the dashboard above the vents. Replace a sensor in the case of a malfunction as indicated on the control display.

Instructions

Front Sensors

1

Park the vehicle level ground. Set the parking brake. Open and raise the hood.

2

Remove the five bumper trim screws from the area just forward of the radiator using a nut driver. Remove the eight bumper trim screws from the bottom edge of the bumper.

3

Remove the two screws from the outer edge at the bottom front of each wheel arch trim using a nut driver. Unsnap the bumper trim catch from the wheel arch trim on both sides.

4

Release the bumper trim catches located on both sides of the bumper trim just below the driving light and at the upper corners of the trim next to the narrow grille strip in the middle

5

Separate the trim from the vehicle slightly and disconnect the electrical connector from the PDC sensor transducers located on the front of the trim just below the inboard passenger trim catch and on each side of the trim. Have a second person help you pull the trim straight forward and off the vehicle.

6

Disconnect the forward transducer holder from the four retaining lugs on the trim. Remove the transducer. Ensure that the rubber ring properly seats on the new transducer. Install the new transducer on the trim and be sure that it seats correctly.

7

Remove the rubber boots from the side transducers. Unclip the transducer retainers and pull the transducer out of the holders. Install the new transducers in the holders. Ensure that the rubber ring properly seats on the transducer and that the transducer properly seats in the holder.

8

Hold the trim in place just forward of its installed position with the aid of a helper. Connect the electrical connectors to the transducer terminals. Install the rubber boots on the transducers. Push the trim piece fully into position and engage the four front clips and the two side clips. Install all of the retaining screws and tighten securely using a nut driver.

Rear Sensors

9

Locate the four transducers in the rear bumper. Two are located right over the exhaust pipes and two are below each corner of the license plate.

10

Lie on the ground and reach up behind the rear bumper. Disconnect the sensors electrical connector from its transducer terminal.

11

Unsnap the retaining tabs from the transducer and pull it from its holder.

12

Install the new transducer in the holder and engage the retaining tabs. Ensure that the rubber ring properly seats on the transducer and that the transducer properly seats in the holder.

13

Plug the electrical connector into the transducer terminal.

The iconic Chevrolet Bowtie symbol is prominently displayed in two locations on the 2011 Silverado; in the center of the front grille and the center of the tailgate. The emblem in the center of the grille is cast into the grille itself and cannot be removed or separated from the grille. The emblem in the center of the tailgate is affixed with double-sided body tape and can easily be removed with a heat gun and plastic scraper. While the emblem is a popular symbol with many owners, some prefer to remove or de-badge their trucks for a cleaner, more simplistic look.

Instructions

1

Wash any dirt and debris from the tailgate with a clean rag and bucket of soapy water. Rinse the soap from the tailgate with clean water and dry the tailgate with a lint-free cloth.

2

Connect your heat gun to an extension cord so your movement isnt restricted. Adjust the temperature dial to a medium setting.

3

Warm the emblem and the area around the emblem with the heat gun for one to two minutes.

4

Insert a clean plastic putty knife in between the emblem and the tail gate. Pry the emblem away from the tailgate while still applying heat with the heat gun. Remove the emblem from the tailgate.

5

Wait four to five minutes for the tailgate to cool to room temperature. Remove any remaining adhesive with paint-safe adhesive remover and a clean, lint-free towel. Dry the area completely with a lint-free towel.